• RE: TUSB1002A: TUSB1002A type C usb3.0 interface

  

  Vishesh Pithadiya

  Hi, No I mean depopulate R78, keep R79 depopulated, and force the flip pin low by populating R107. Afterwards, do the same tests the resulted in this table. Damodaran Nagarajan said: Flip input to TUSB1104 HOST USB to J1 J2 USB TO Device…

  • 16 days ago
  • Interface
  • Interface forum

• TUSB1002A: Will having Two TUSB1002A in the System "cancel" the switch from TX to RX and Vice Versa when using this linear redriver?

  

  Arron Danehy

  TI Thinks Resolved

  Part Number: TUSB1002A Tool/software: Hello, I am designing a long meter cable that consists of 3 different junctions. See the image below for reference: I know when creating a USB A to USB B cable the RX and TX switch, which happens on the redriver…

  • 2 months ago
  • Interface
  • Interface forum

• TUSB1002A: TUSB1002A placement suggestion

  

  Vincent Chiu

  TI Thinks Resolved

  Part Number: TUSB1002A Other Parts Discussed in Thread: TUSB522P Tool/software: Hi TI Expert Our placement is below, total trace length from Jeston Orin (host) to type-c connector is around 12.3 inch, which is over Jeston Orin's layout guidance (maximum…

  • 9 months ago
  • Interface
  • Interface forum

• TUSB1002A: Function issues

  

  Yadong Duan

  TI Thinks Resolved

  Part Number: TUSB1002A Tool/software: Hi Team, Does TI have integrate the USB2.0 and USB3.0 redriver? Many thanks~

  • 4 months ago
  • Interface
  • Interface forum

• TUSB1002A: Function confirmation

  

  Yadong Duan

  TI Thinks Resolved

  Part Number: TUSB1002A Tool/software: Hi Team, The datasheet of the TUSB1002A shown that the minimum length of Lac-cap to be 0.25 inches. If the layout space is limited and the distance between CAP and re-driver is less than 0.25 inches (not meeting…

  • 4 months ago
  • Interface
  • Interface forum

• TUSB1002A: Function confirmation

  

  Yadong Duan

  TI Thinks Resolved

  Part Number: TUSB1002A Tool/software: Hi Team, Datasheet shown that pin19/20 as TX and pin22/23 as RX, if customer want to use the function, does the PIN12/11 and PIN8/9 need swap it? Many thanks~

  • 5 months ago
  • Interface
  • Interface forum

• TUSB1002A: How to use two TUSB1002A in series?

  

  Jeffrey Kleck

  TI Thinks Resolved

  Part Number: TUSB1002A Designing an USB 3.2 isolator and would like to know how to use two TUSB1002A on each side of the isolation barrier? How does the automatic RX termination and RX detection work when two TUSB1002A are tied in series? I am having…

  • over 1 year ago
  • Interface
  • Interface forum

• TUSB1002A: EQ and CFG selection

  

  Naizeng Wang

  Part Number: TUSB1002A Tool/software: Hi team. I think customer can choose EQ8 for CH1 and EQ4 for CH2, correct? Which CFG should they select? I don't konw how to select it.

  • 5 months ago
  • Interface
  • Interface forum

• TUSB1002A: TX AC cap to host

  

  Woon Nee Tan

  TI Thinks Resolved

  Part Number: TUSB1002A Tool/software: Hi, I would like to confirm what AC cap should be used for TX to host. As the USB3.2 standard and CPU (host) vendor recommend to use 330nF. But in TUSB1002A suggest to use 220nF. Please clarify. Thanks.

  • 5 months ago
  • Interface
  • Interface forum

• TUSB1002A: EQ setting

  

  Yadong Duan

  TI Thinks Resolved

  Part Number: TUSB1002A Tool/software: Hi Team, Pre channel loss 11.47dB ，Po st channel 2.23dB; customer want to check if TUSB1002A can support it. would you please help me check it? Customer want to check the EQ setting, do you have any suggestion…

  • 7 months ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.