Answered

• TUSB8043: Upstream and Downstream Power Supply

  

  Yuta Nishie

  Resolved

  Part Number: TUSB8043 Hi, I have any question about upstream and downstream power supply(VBUS). ・upstream 1. Because there is no need to monitor the power supply of VBUS, is it OK to connect USB_VBUS of 48pin to GND at 10 kΩ? Even if there is no…

  • Resolved

  • over 1 year ago
  • Interface
  • Interface forum

• TUSB8043: EEPROM Programmer tool

  

  Len Hsu2

  TI Thinks Resolved

  Part Number: TUSB8043 Hi team, I have a customer design in TUSB8043 and need the EEPROM Programmer tool. Can you help on this?

  • over 1 year ago
  • Interface
  • Interface forum

• TUSB8043: USB3.0 downstream LTE module interfacing

  

  bharath kumar

  Part Number: TUSB8043 Other Parts Discussed in Thread: TUSB8044AEVM HI All, We have used USB hub controller (TUSB8043RGCT) in our design. According to the design, we have connected the upstream to Host processor and Down stream(USB 3.0) Port 1 is connected…

  • over 2 years ago
  • Interface
  • Interface forum

• TUSB8043: Is there any additional configuration need to be consider when only use the USB2.0 of TUSB8043?

  

  Matthew Chen

  Part Number: TUSB8043 Hi TEAM, Apart from the Enable pin, Is there anything should be concerned when use TUSB8403 only for USB2.0? Thanks a lot Matthew Chen

  • over 2 years ago
  • Interface
  • Interface forum
Answered

• TUSB8043: Programing EEPROM via HID to I2C Interface

  

  Jamal Ahmed

  Resolved

  Part Number: TUSB8043 Hello, I would like to know how the upstream USB port is used to program the EEPROM via the HID to I2C interface. Is this programing only limited to a specific tool or any host processor can do this? I am intending to use this hub…

  • Resolved

  • over 2 years ago
  • Interface
  • Interface forum
Answered

• TUSB8043: Can't find TUSB8043 on EEPROM programmer tool

  

  Gary Teng

  Resolved

  Part Number: TUSB8043 Hi sir, My customer want to use EEPROM programmer to setup their TUB804x but the GUI cant find TUSB804x device. Is there any driver (programming endpoint driver) we need for using the GUI? Thanks for your kindly help. Best regards…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• TUSB8043: USB camera is not working on TUSB8043 USB HUB

  

  Carlo

  TI Thinks Resolved

  Part Number: TUSB8043 Hi E2E, Good day. Our customer is using TUSB8043 and interfaces it with Jetson Xavier NX SOM. In the Down Stream USB port, they're connecting 3.0 USB Camera i.e. 12MPx. The camera is detected on highspeed lines but the customer…

  • over 3 years ago
  • Interface
  • Interface forum

• TUSB8043: realize USB3.0

  

  Wendy Wang1

  TI Thinks Resolved

  Part Number: TUSB8043 Hi team, I'm not familiar with this TUSB8043RGC device. Do we need to load firmware or flash some software to realize usb3.0? Thanks a lot! Thanks & best regards, Wendy

  • over 3 years ago
  • Interface
  • Interface forum

• TUSB8043: We are observing the USB 3.0 connection detected in USB 2.0

  

  Senthil Kumar

  TI Thinks Resolved

  Part Number: TUSB8043 1. We are using the TUSB8043 USB HUB controller in our USB 3.0 camera products 2.Four boards observed USB 2.0 connection instead of USB 2.0 3.And the issue was resoled after solder touch up on the pins around ,but as per X-ray reports…

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• TUSB8043: Slave address not available in I2C master mode

  

  Koshi Ninomiya

  Resolved

  Part Number: TUSB8043 Dear Team, My customer is looking at TUSB8043 as USB Hub with GPIO feature. They want to c ontrol peripheral devices from the USB Hub with GPIO etc. Although the TUSB8043 can operate as I2C master mode, are there any Slave addresses…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.