Answered

• TVS1400: Simulation of in rush current

  

  Shane Buckham

  Resolved

  Part Number: TVS1401 Other Parts Discussed in Thread: TVS1400 Tool/software: Hi, I have exactly the same issue. I want to use the TVS1401 across the DC power input in a hot pugging situation. I have some ideas on how to manage this inrush but need to simulate…

  • Resolved

  • 4 months ago
  • Interface
  • Interface forum
Answered

• TVS1400: Forward voltage across current

  

  Shane Buckham

  Resolved

  Part Number: TVS1400 Tool/software: Hi, I have the same question as the closed linked thread. Figure 6 of Datasheet SLVSED3A March 2018 states "Forward Voltage vs Temperature Across Current" except that only one current is shown so it's not…

  • Resolved

  • 4 months ago
  • Interface
  • Interface forum

• TVS1400: Generating voltage??

  

  Rob Klein

  Part Number: TVS1400 Tool/software: I am currently developing a simple PLC-like interface for one of our products. Nothing very complicated, a few digital in- and outputs, as well as an analog input and analog output. The analog I/O is 0-10V, so I thought…

  • 8 months ago
  • Interface
  • Interface forum

• TVS1400: TVS1400 rating in the 10/1000us waveform

  

  Chen Alex1

  TI Thinks Resolved

  Part Number: TVS1400 hi sir in the 10/1000us waveform~ TVS1400 only rating 60w TV04WF can rating to 400w right? TVS1400: TV04WF:

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• TVS1400: protecting SN65HVD230D

  

  Victor Tolosana

  Resolved

  Part Number: TVS1400 Other Parts Discussed in Thread: SN65HVD230 Hello, Would the TVS1400 protection device be a good fit to protect a SN65HVD230D working at 1Mbaud ? Breakdown and clamping voltages seem to be adequate. I need the SN65HVD230 protected…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• TVS1400: TVS1400

  

  Sudarshan KR

  TI Thinks Resolved

  Part Number: TVS1400 Other Parts Discussed in Thread: TVS0500 , TVS0701 , Hi, In my earlier post i had raised the below query Planning to use TVS1400 on 12V DC line and TVS0500 on 6.2V DC Line. Since on TVS0500 VRWM is 5V, but the Clamping voltage is 9.2V and…

  • over 4 years ago
  • Interface
  • Interface forum

• RE: THVD1550: At a rate of 10Mbps, 100 feet of cable length, its signal jitter

  

  Ethan Sempsrott

  Hi Rhea, I apologize for the delay. Here are my comments: There are failsafe resistors that are not needed for THVD1550 (1K Ohm near the 100pF caps). SN65176B requires an external failsafe configuration, but THVD1550 has it internally so those resistors…

  • 25 days ago
  • Interface
  • Interface forum

• TVS1400: inrush current

  

  Yasuhara

  TI Thinks Resolved

  Part Number: TVS1400 TVS1400DRVR is used on the power line of the power connector (hot plug). When the power is turned on with the hot plug, the inrush current will increase if the TVS1400DRVR is used.(As much as with a 1uF capacitor) When the TVS1400DRVR…

  • over 4 years ago
  • Interface
  • Interface forum

• TVS1400: Part Selection

  

  Sudarshan KR

  TI Thinks Resolved

  Part Number: TVS1400 Other Parts Discussed in Thread: TVS0500 Hi, Planning to use TVS1400 on 12V DC line and TVS0500 on 6.2V DC Line. Since on TVS0500 VRWM is 5V, but the Clamping voltage is 9.2V and the Vbris around 7.7V Are my part selection OK Regards…

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• TVS1400: Interface forum

  

  Sudarshan KR

  Resolved

  Part Number: TVS1400 Other Parts Discussed in Thread: TVS0500 Hi, Planning to use TVS1400 on 12V DC line and TVS0500 on 6.2V DC Line. Since on TVS0500 VRWM is 5V, but the Clamping voltage is 9.2V and the Vbr is around 7.7V Are my part selection OK Regards…

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.