Answered

• TXB0106: Is it recommended to add the serial resistors between TXB0106 and MCU?

  

  Shaofeng Luo

  Resolved

  Part Number: TXB0106 Hi experts team In the application circuit, do we recommend to add the serial resistors between MCU and TXB0106? Like 22ohm or 30ohm.

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• TXB0106: OE pin problem

  

  ?? ?

  TI Thinks Resolved

  Part Number: TXB0106 Tool/software: Designed for 1.8V to 3.3V VccA=1.8V；VccB=3.3V According to the specification OE pin needs to be Referenced to VCCA. But in the experiment, if the IC uses 1.8V, it will not be able to output. It needs to use 3…

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• TXB0106: TXB0106 IO pins

  

  Nachiketh Karanth

  Resolved

  Part Number: TXB0106 Hi, I am using the part TXB0106RGYR. 1. Can we leave the input output pins floating? Regards, Nachiketh

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• TXB0106: switch level for Ioff circuitry

  

  Thomas Krause

  TI Thinks Resolved

  Part Number: TXB0106 Tool/software: Hi all, in the datasheet is an Ioff circuitry mentioned that will set the IO´s to High-Z if one of the Vcc´s is zero. But nowhere is the voltage level mentioned when this switchover will occur. Is this tested during…

  • over 1 year ago
  • Logic
  • Logic forum

• TXB0106: Design review

  

  Apurva Agre

  TI Thinks Resolved

  Part Number: TXB0106 Other Parts Discussed in Thread: TXU0204 , TXU0202 Tool/software: Hello, In our design, we are using the TXB0106PWR. The METER_UART signals are given to the UART-RS485 transceiver through translator and opto-coupler. Since the controller…

  • over 1 year ago
  • Logic
  • Logic forum

• TXB0106: The speed support on Vcca = 1.2V

  

  Maurice Chiu

  TI Thinks Resolved

  Part Number: TXB0106 Tool/software: Hi TI Experts, I would like to survey the level shift for 1.2V Processor to 1.8V QuadSPI flash. And I find that TXB0106 for SPI but only 20Mbps support when Vcca = 1.2V. Is there any other recommended part…

  • over 1 year ago
  • Logic
  • Logic forum

• TXB0106-Q1: SPI Waveform distortion over 800KHz

  

  Andy Jin

  Part Number: TXB0106-Q1 Tool/software: Hi Expert, The VCCA is 3.3V ,VCCB is 5.0V. The CLK waveform is OK in the A port, but the output waveform is very bad when the frequency is over 800KHz. Please help check what's wrong with it. Thanks a…

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• TXB0106: Schematics review

  

  PYTsai

  Resolved

  Part Number: TXB0106 Other Parts Discussed in Thread: TXS0102 , TXU0304 , TXU0104 , TXU0204 Tool/software: Hi we would like to do 3.0V I2C and 3.6V I2C convert. can you help review my schematics below, if they looks ok ? thanks!

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum

• TXB0106: for SD card IO translation

  

  Kevin San Diego

  TI Thinks Resolved

  Part Number: TXB0106 Other Parts Discussed in Thread: LSF0108 , , TXS0206A , TXS02612 Tool/software: is there any reason the TXB0106 or LSF0108 Auto-Bidirectional voltage translators could not work in place of application specific translators like TSX0206A…

  • over 1 year ago
  • Logic
  • Logic forum

• TXB0106: I need to know the reflow soldering profile

  

  Irfan Shaikh

  TI Thinks Resolved

  Part Number: TXB0106 Other Parts Discussed in Thread: TMUXHS4412 Tool/software: Hi team, can you please share the reflow soldering profile for TXB0106RGYR. Also if possible can you also share the same for TXS0102DCUR and TMUXHS4412IRUAT. Than…

  • over 1 year ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.