Answered

• TXB0106-Q1: Use of TXB0106-Q1 as level shifter

  

  kyle oliveira

  Resolved

  Part Number: TXB0106-Q1 Hello, I am writing to make sure that my planned use of the TXB0106-Q1 as a 5.0V->3.3V level shifter will work. I intend to drive an attenuator that requires 6 3.3V control signals with our hardware driver that uses 5.0V logic…

  • Resolved

  • 2 months ago
  • Logic
  • Logic forum
Answered

• TXB0106-Q1: Dealing with un-used pins on the TXB0106-Q1 level shifter

  

  kyle oliveira

  Resolved

  Part Number: TXB0106-Q1 Hello, I am using the TXB0106-Q1 to level shift a number of logic pins from 5.0 to 3.3v, and due to the # of pins not being a multiple of 6, i have some leftovers on the last level shift IC. Schematic of this IC attached below…

  • Resolved

  • 1 month ago
  • Logic
  • Logic forum

• TXB0106-Q1: Unsure of how to tie TI level shifter Output Enable pin to ground

  

  kyle oliveira

  TI Thinks Resolved

  Part Number: TXB0106-Q1 Hello, I am designing the TXB0106-Q1 part into my system as a level shifter, and am unsure how to tie the OE pin to ground. the datasheet has this to say: "To ensure the high-impedance state during power up or power down, OE…

  • 1 month ago
  • Logic
  • Logic forum

• TXB0106-Q1: Request to provide questionnaire for TXB0106QWBQBRQ1

  

  Uday Kumar

  TI Thinks Resolved

  Part Number: TXB0106-Q1 Hi Team, Hope you are doing good !! We have received a new part request for the 'MPN: TXB0106QWBQBRQ1 NewPartQuestionnaire_TI_TXB0106QWBQBRQ1.xlsx ' which is requested for the project 'ADAS'. I have attached the questionnaire…

  • 2 months ago
  • Power management
  • Power management forum

• TXB0106-Q1: SPI Waveform distortion over 800KHz

  

  Andy Jin

  Part Number: TXB0106-Q1 Tool/software: Hi Expert, The VCCA is 3.3V ,VCCB is 5.0V. The CLK waveform is OK in the A port, but the output waveform is very bad when the frequency is over 800KHz. Please help check what's wrong with it. Thanks a…

  • over 1 year ago
  • Logic
  • Logic forum

• TXB0106-Q1: Regulation Certification Report

  

  Colt Zhang

  TI Thinks Resolved

  Part Number: TXB0106-Q1 hi team, could you help provide the AEC-Q100 report of TXB0106-Q1, i can't find the report in the TI.com

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• TXB0106-Q1: Has the same die with TXB0106?

  

  ArTzy

  Resolved

  Part Number: TXB0106-Q1 Hi Experts, Good day. We would like to ask your confirmation if the automotive version has the same die with its commercial variant. Also, we know that automotive has high reliability for zero defects, as such should we assume…

  • Resolved

  • over 4 years ago
  • Logic
  • Logic forum

• TXB0106-Q1: TXB0106-Q1

  

  MaWü

  TI Thinks Resolved

  Part Number: TXB0106-Q1 Other Parts Discussed in Thread: LSF0204-Q1 Hello, does TXB0106-Q1 supports 100MHz translation like LSF0204-Q1? I need a "Auto-Bidirectional Multi-Voltage Level Translator" for QSPI running with 85MHz clock. Regards MW

  • over 5 years ago
  • Logic
  • Logic forum

• TXB0106-Q1: Both I/O ports can keep HIGH voltage

  

  Frank QIN

  TI Thinks Resolved

  Part Number: TXB0106-Q1 Hello Team, We are using TXB0106IPWRQ1 and found some abnormal behavior. When both ports of I/O are high impedance or floating, after apply a short pull up signal and then remove, both I/O ports can keep high voltage level…

  • over 3 years ago
  • Logic
  • Logic forum

• TXB0106-Q1: replacement solution

  

  Chuqiang Wen

  TI Thinks Resolved

  Part Number: TXB0106-Q1 Other Parts Discussed in Thread: TXU0304-Q1 , TXU0104-Q1 , TXU0204-Q1 , TXB0104-Q1 Hi Expert, My customer is finding the backup solution for TXB0106-Q1 in current supply constraint situation. Do we have other device can P2P with…

  • over 4 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.