Answered

• TXB0302: Spec Clarification

  

  Kazuki Itoh

  Resolved

  Part Number: TXB0302 Hi team, (1) Is it possible to input 1.8V to VCCB and a signal with 3.3V amplitude to Vin(B)? Considering 3.3V +10%, the amplitude may reach up to 3.63V. I understand that the recommended operating conditions state VCC, and…

  • Resolved

  • 1 month ago
  • Interface
  • Interface forum

• TXB0302: Test mode, only weak pullups driving both sides of TXB0302

  

  ron Hall

  TI Thinks Resolved

  Part Number: TXB0302 Circuit has a test mode where both sides of TXB0302 are tri-stated. 20K+ pullup on 3.3V side, 25K + pulldown on 2.5V side. 2nd data path has 40K and 20K pullups. I presume the output state of the TB0302 is indeterminate since none…

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• TXB0302: foot print

  

  Shoo Saga

  Resolved

  Part Number: TXB0302 Tool/software: Hi What is the length of A and B? Regards, Shoo

  • Resolved

  • over 1 year ago
  • Logic
  • Logic forum
Answered

• TXB0302: why TXB0302 can't use for open drain case

  

  weilun luo

  Resolved

  Part Number: TXB0302 Other Parts Discussed in Thread: TXS0102 , LSF0102 Could you explain why TXB0302 can't use for open drain case? Could you show me the fail case?

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• TXB0302: Question about data rate (timing requirements).

  

  Diara Beltran

  Answer Suggested

  Part Number: TXB0302 Other Parts Discussed in Thread: TXB-EVM Hi, Our design team have a question about P/N TXB0302DQMR. See question below: Q1: Is this the maximum possible data rate? or is it guaranteed to do that amount? See information from…

  • over 2 years ago
  • Logic
  • Logic forum

• TXB0302: Can open drain signals be connected to this

  

  Premalatha Royappan

  TI Thinks Resolved

  Part Number: TXB0302 Other Parts Discussed in Thread: TXU0202 Hi We are using TXB0302DQMR in our design. Following is our implementation Since INTR signal( connected to pin 2) is an open drain signal we are facing issue.The signal is not toggling…

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• TXB0302: Usage of IBIS model

  

  Yuji Matsumoto

  Resolved

  Part Number: TXB0302 Hi TI team. We would like to use IBIS model of TXB0302, but we're not sure how to use it. 1) There is no input model for the A1/A2/B1/B2 pin. 　How can we simulate input signal for TXB0302? 2) We would like to simulate…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum
Answered

• TXB0302: Sink current capability requirement

  

  Kazuki Itoh

  Resolved

  Part Number: TXB0302 Hi team, I have a question about the TXB0302 datasheet. I think Figure 2 describes the required input drive current requirement of external push-pull. (2) mentions VD is the supply voltage of the external driver. But I don…

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• TXB0102: Difference between TXB0102 and TXB0302 ?

  

  Vivien Delfosse1

  Answer Suggested

  Part Number: TXB0102 Other Parts Discussed in Thread: TXB0302 , TXU0304 , TXU0104 , TXU0204 Hello dear support community, Everything is in the title, could you please explain me what is the difference between TXB0102 and TXB0302 components please…

  • over 3 years ago
  • Logic
  • Logic forum

• TXB0302: Level Translator for MDC and MDIO

  

  JH Shin

  TI Thinks Resolved

  Part Number: TXB0302 Other Parts Discussed in Thread: TXS0102 , LSF0102 Hello, Can TXB0302 be used as a level translaotr between 3.3V and 2.5V for MDC and MDIC? My customer wants to know if TXB0302 can be used as a level translator for MDC and MDIO…

  • over 3 years ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.