• TXS0102: Requesting Alternative for TXS0102 with Higher Capacitive Load Driving Capability

  

  Yuxi Liu(Tony)

  Answer Suggested

  Part Number: TXS0102 Other Parts Discussed in Thread: TXU0202 Hi Team, We have a customer currently using the TXS0102 voltage-level translator for I2C and UART protocols. The customer is experiencing waveform distortion in their application due to…

  • 1 month ago
  • Logic
  • Logic forum
Answered

• TXS0102-Q1: Short Circuit Protection - Best Method to Protect TXS0102

  

  Kevin Richardson

  Resolved

  Part Number: TXS0102-Q1 Other Parts Discussed in Thread: TXS0102 , TXU0102-Q1 Hello, I am currently facing an issue in determining the best path forward to adequately protect the TXS0102 from a direct short to GND at the IO port. Would the best…

  • Resolved

  • 3 months ago
  • Interface
  • Interface forum
Answered

• TXS0102: Does the TXS0102 have a metal bottom?

  

  Charles Wolfe

  Resolved

  Part Number: TXS0102 Tool/software: Does the TXS0102 have a metal bottom? Based off that datasheet it looks like it does NOT have a metal bottom, but I want to confirm.

  • Resolved

  • 8 months ago
  • Power management
  • Power management forum
Answered

• TXS0102: TXS0102 malfunction

  

  reza anvari

  Resolved

  Part Number: TXS0102 Other Parts Discussed in Thread: TCA9416 Tool/software: Hello, I am using the TXS0102 as a level translator between 1.8V and 3.3V for an I2C bus. There are external pull-up resistors configured as shown in the picture below. On…

  • Resolved

  • 10 months ago
  • Logic
  • Logic forum

• TXS0102: Design Inquiry

  

  Abhishek Manoj

  TI Thinks Resolved

  Part Number: TXS0102 Hi Team, I was planning to use the 2 channel level translator TXS0102DCUR for converting my UART signals from 3.3V to 1.8V. I have used the same level translator for UART in my other projects, it was working fine. Does using…

  • 2 months ago
  • Interface
  • Interface forum

• TXS0102: Marking TXS0102DCTT

  

  Sławomir Ślipek

  TI Thinks Resolved

  Part Number: TXS0102 Good morning I need help in determining whether the 2ST5 marking is correct for: TXS0102DCTT DC 2237 and DC 2347

  • 2 months ago
  • Data converters
  • Data converters forum

• TXS0102: shift issue

  

  Tommy Tzeng

  TI Thinks Resolved

  Part Number: TXS0102 Hi Team, we currently using the TXS0102 device for the MIIM interface design and have the following issue that we would like your assistance in confirm, MAC side voltage:3.3v, PHY sode voltage:2.5v, TXS0102: OE pin is pulled…

  • 1 month ago
  • Logic
  • Logic forum

• TXS0102: Product and design inquiry

  

  Abhishek Manoj

  TI Thinks Resolved

  Part Number: TXS0102 Hi Team, For my bidirectional one-wire signal need to be level translated from 5V to 3.3V in my board. I was planning to use the TXS0102 for this level translation, but it got the below query "1-Wire is open-drain, pull-up based…

  • 1 month ago
  • Power management
  • Power management forum
Answered

• TXS0102: ComponentDataSheet

  

  mie koyama

  Resolved

  Part Number: TXS0102 This is Koyama from NTT Electronics Cross Technology. We sincerely appreciate your continued support and patronage. We kindly request your assistance in entering data into the attached document. TXS0102DCTR Desired Delivery Date…

  • Resolved

  • 3 months ago
  • Logic
  • Logic forum

• TXS0102: Different IC markings have different characteristics

  

  Allen yang

  TI Thinks Resolved

  Part Number: TXS0102 Hi Team, The factory reported that the TXS0102DCTR received material has two different marks. When the NG mark material is used, the TXS0102DCTR fails to function properly. OK marker: 35UT NG: NFE 631X 5CR

  • 18 days ago
  • Logic
  • Logic forum

Didn't find what you are looking for? Post a new question.