Answered

• UCC44273: vs UCC27516/7A

  

  Taku Murayama

  Resolved

  Part Number: UCC44273 Other Parts Discussed in Thread: UCC27516 What is the difference among UCC44273 vs UCC27516/7A? What do you mean by "Industry-standard pinout with 2 output pins" for UCC44273 in promotion material?

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• UCC27516: UCC277516 undershoot voltage

  

  Boon Tian Kwan

  Resolved

  Part Number: UCC27516 Hi, What is the UCC27516 OUT pin allowable undershoot voltage? Best regards, BT

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• UCC27516: Input bias current at 12V

  

  Sonia Dupuch

  Resolved

  Part Number: UCC27516 What is the input bias current at 12V into the IN+ pin. Is this purely the pull down resistor or is there further leakage into the pin logic?

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• UCC27516: Can this chip drive PMOS transistors?

  

  zhu

  Resolved

  Part Number: UCC27516 I searched for the gate driver of TI and found that the typical circuits provided in the information are all based on N-MOS transistors. Do TI have an IC that drives P-MOS transistors? Whether it is a high-end driver or a low-end…

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum

• UCC27516: High-side configuration

  

  Ryan Pang

  TI Thinks Resolved

  Part Number: UCC27516 Other Parts Discussed in Thread: UCC27614 , UCC27322 I need a gate driver for a front end power amp switching application - A Power MOSFET switches the drain bias of a PA on and off with a p-channel MOSFET configured as a high-side…

  • over 4 years ago
  • Power management
  • Power management forum
Answered

• UCC27516: I'm looking for a single drive IC

  

  Kaji@PAN

  Resolved

  Part Number: UCC27516 Other Parts Discussed in Thread: UCC27517 HI, I'm looking for a single drive IC that can drive the gates of MOSFETs in boost chopper circuits used in PFC circuits. As a condition ・Pulse signal voltage input to the device : 5V…

  • Resolved

  • over 5 years ago
  • Power management
  • Power management forum
Answered

• CD4504B: 3.3 V to 15 V Translator with CD 4504

  

  Varunesh Kumar

  Resolved

  Part Number: CD4504B Other Parts Discussed in Thread: UCC37324 , UCC27516 , TLC3704 Hello I am looking for a Low to High ( 3.3 V to 15 V ) Translator with at least 10 mA Source & Sink capability for Interface between our DSP and IGBT Drivers. …

  • Resolved

  • over 2 years ago
  • Logic
  • Logic forum

• SN74ACT04: How to increase out drive current.

  

  Kazuya Nakai59

  TI Thinks Resolved

  Part Number: SN74ACT04 Other Parts Discussed in Thread: UCC27516 , UCC27523 Hello guys, I have 2 questions. Could you please give me your reply? One of my customer uses SN74ACT04PWR for their current products. For their new products, they need to…

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• SN74LVC1G126: Output of 1G126 when the OE is 0.8V

  

  user4090349

  Resolved

  Part Number: SN74LVC1G126 Other Parts Discussed in Thread: TPS3897 , UCC27516 , UCC27517 Hello I would like to understand the power up status of 1G126. I use the TPS3897 output to control the OE of 1G126. During the power up process, the output of…

  • Resolved

  • over 3 years ago
  • Logic
  • Logic forum
Answered

• UCC27517: Continuous enabled non-inverted (DBVR) input mode output reverse current sinks 500mA

  

  Genatco

  Resolved

  Part Number: UCC27517 Other Parts Discussed in Thread: UCC27714 , UCC27516 Hello forum gurus, How can output sink 300mA continuous absolute maximum but also accept 500mA reverse, AKA negative current flow (Pg16,Fig.23)while the input is at CMOS low…

  • Resolved

  • over 4 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.