TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 80 results View by: Thread Post Sort by
  • TPS2553D: Current limit & RILIM.

    Yee Yong Teo
    Yee Yong Teo
    TI Thinks Resolved
    Part Number: TPS2553D Hi, On the website, under the parameters table, TPS2553D can support 1.7A continuous current. But in the datasheet, it is written 1.5A continuous current. Which one should I follow? In order to make sure the current limit stays…
    • over 8 years ago
    • Interface
    • Interface forum
  • Answered
  • TPS2553D: About SOA of FET inside device

    Kaji@PAN
    Kaji@PAN
    Resolved
    Part Number: TPS2553D Hi, I am checking the operation of the circuit using TPS2553D device. Among them, a large rush current occurs when the USB power bus HDD is connected. See attached figure. Looking at the data sheet in Figure16, I think that this…
    • Resolved
    • over 7 years ago
    • Interface
    • Interface forum
  • Answered
  • TPS2553D: Over current detection

    Takahiro Saito
    Takahiro Saito
    Resolved
    Part Number: TPS2553D Hello team, The TPS2553D does not have two current limit values like the following pictures, is it right? The TPS2553D can detect the over current when the current exceeds Ios more than 2us typ, is it right? Regards, Taka…
    • Resolved
    • over 8 years ago
    • Interface
    • Interface forum
  • TPS2553D: Reverse Voltage

    Vladislav Blad
    Vladislav Blad
    TI Thinks Resolved
    Part Number: TPS2553D Hello, In follow condition: Vin = 0V and Vout = 5V will Reverse Voltage protection work? Best regards, Vladislav
    • over 8 years ago
    • Interface
    • Interface forum
  • TPS2553D: Reverse Voltage

    mayumi.T
    mayumi.T
    Answer Suggested
    Part Number: TPS2553D Hello, My customer has a question. I think that the condition of REVERSE-VOLTAGE PROTECTION is as follows. (Vout-Vin)>135mV The test conditions do not meet this requirement. (Vin = 5 V, Vo = 5 V) Therefore I understand…
    • over 8 years ago
    • Interface
    • Interface forum
  • TPS2553D: Current Limit

    tateo yamashiro
    tateo yamashiro
    TI Thinks Resolved
    Part Number: TPS2553D Other Parts Discussed in Thread: TPS2553 Hi, We got a question from customer about TPS2553D. Could you help us? [Question] They would like to make sure the measurement value of current limit under the following condition. …
    • over 8 years ago
    • Interface
    • Interface forum
  • TPS2553D: Rise time, output

    tateo yamashiro
    tateo yamashiro
    TI Thinks Resolved
    Part Number: TPS2553D Hi, We got a question from customer about TPS2553D. Could you help us? [Question] How much is the minimum value of output rise time(tr) at Vin=3.3V? They don't need gurantee. They only use for reference. Best Regards, tate…
    • over 8 years ago
    • Interface
    • Interface forum
  • TPS2553D: Short Circuit and Over Current protect

    Tamio Yokokura
    Tamio Yokokura
    TI Thinks Resolved
    Part Number: TPS2553D Other Parts Discussed in Thread: TPS2069C , TPS25810 , TPS2553 Hi, Support team The below is a sequence of short circuit and over current limit protection I created. I have soome question as follows, [1] As far as I see…
    • over 7 years ago
    • Interface
    • Interface forum
  • RE: TPS2553D: FAULT signal not active during overcurrent

    Bob Ma
    Bob Ma
    Hi, Faizul, I know the current limit range is from 234mA to 303mA when it's set at 266mA. But if your test condition(temperature, Vin...) not change, the variation of current limit will be very small. It should be close to 266mA, in my test it's around…
    • over 7 years ago
    • Interface
    • Interface forum
  • TPS2553D drooping characteristic

    Ryuuichi machida
    Ryuuichi machida
    Other Parts Discussed in Thread: TPS2553D Hi, I would like you to confirm drooping characteristic of TPS2553D. My customer try to use this device, but they could not observe this drooping characteristic. Cin and Cout are used 0.1uF and Rilim is…
    • over 9 years ago
    • Power management
    • Power management forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question