TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 436 results View by: Thread Post Sort by
  • RE: TPS61200 - Vout_Setting < external_Battery_Voltage

    Dice-K
    Dice-K
    Hello Charles, Thank you for your reply. I have a answer of TPS63020. This answer describes the attention of PS=disabled. Does a same thing happen in TPS61200? Best regards, Daisuke
    • over 11 years ago
    • Power management
    • Power management forum
  • Schematic Review

    Pradhan Rivankar
    Pradhan Rivankar
    TI Thinks Resolved
    Other Parts Discussed in Thread: BQ24650 , BQ28Z610 , TLV62080 , TPS63020 , TLV713 Dear Sir/ Madam We are working on Agriculture based Project in which we are using below Ti Part no. Charge Controller : BQ24650 Fuel Gauge : BQ28z610 Power Regulator…
    • over 10 years ago
    • Power management
    • Power management forum
  • Answered
  • BQ24133

    James Del Signore
    James Del Signore
    Resolved
    Other Parts Discussed in Thread: TPS63020 , BQ24133 , BQ24630 I am debugging prototype BQ24133/TPS63020 battery support design for single cell application. It uses a BQ24133 driving a TPS63020 buck/boost to keep output voltage constant at 5V over tolerances…
    • Resolved
    • over 11 years ago
    • Power management
    • Power management forum
  • RE: Need help on schematics verification

    Michael Green
    Michael Green
    Hi, I see that some of your power is from discrete converters. I am not the expert in those devices but, noticed that if you are not using the PG signal output from the TPS63020 you would probably not need the pull up resistor R22. Otherwise, to get…
    • over 12 years ago
    • Power management
    • Power management forum
  • RE: RTOS/TM4C129XNCZAD: TM4C Energy Optimizations

    Muhammad Shuaib
    Muhammad Shuaib
    Hi Charles, Thanks for the update. I have disabled all the components that i can on my system board. Some peripherals are powered via a switch( TPS63020 ) and i don't have the enable pin in my control. Instead, i have enabled the IC's power save mode…
    • over 9 years ago
    • Arm-based microcontrollers
    • Arm-based microcontrollers forum
  • RE: A look inside the Young Optics' Light Engine in LightCrafter

    PedroGelabert
    PedroGelabert
    The LightCrafter LED Driver is a modified version of the LED driver shown in section 3 of this application note: Different methods to Drive LEDs Using TPS630xx Buck-Boost Converters Our modification adds PWM control to the feedback path of the DC-DC…
    • over 11 years ago
    • DLP®︎ products
    • DLP products forum
  • RE: Using the AMC7820 with low-voltage micro-TEC devices (Vmax = 1.4V, Imax = 0.7A)

    Ryan Gehmlich
    Ryan Gehmlich
    Hi Matt, I did look at the AMC7820, but with only three DACs, I don't think it will practically fit on the board (I would need 32 of them). My current solution is to use 32-channel DACs, then as a final stage for the TEC drivers, to use the TPS63020…
    • over 10 years ago
    • Data converters
    • Data converters forum
  • Max driving current driving capability of BQ24253 with 5V, 2A input supply

    Siddalingayya CG
    Siddalingayya CG
    TI Thinks Resolved
    Other Parts Discussed in Thread: BQ24253 , TPS63020 Hello all, I have designed battery management circuit using BQ24253. I want to get 5V, 1.5A output across BQ24253. I have taken ref design from the data sheet. Please find the attached circuit diagram…
    • over 12 years ago
    • Power management
    • Power management forum
  • Answered
  • RE: TPS63050: Issue Integrating buck/boost converter with bq25505 energy harvester

    Milos
    Milos
    Resolved
    Hello Aaron, What is the maximum output current in your design? The non-BGA alternatives to TPS63050 are: - TPS63000 which has larger input voltage range, but operates at lower switching frequency and therefore needs somewhat larger inductor and filtering…
    • over 7 years ago
    • Power management
    • Power management forum
  • RE: LOOKING FOR BUCK-BOOST

    Chris Glaser
    Chris Glaser
    See if you can split your output into 2 pieces and use 2x TPS63020.
    • over 13 years ago
    • Power management
    • Power management forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question