PP-SALB-EVM: PP-SALB-EVM PPC3 Software App

ROGER DAVIS

Part Number: PP-SALB-EVM
Other Parts Discussed in Thread: TAS5720M, TAS5766M

I have recently purchased the PP-SALB-EVM. I also have downloaded the Purepath Console 3 software. It looks like I need the PP-SALB-EVM App in order to use the EVM with PPC3. How do I obtain the EVM App? I am not able to locate any software module app for this EVM.

over 7 years ago

0 Shawn Zheng over 7 years ago

TI__Mastermind 24835 points

Hi Roger,
The installation/access to the PPC3 APP needs to be approved. Could you please let me know the following info:
1. which amp deivce are you evaluating?
2. your TI account
Best regards,
Shawn Zheng

0 ROGER DAVIS over 7 years ago in reply to Shawn Zheng

Prodigy 50 points

Hi Shawn,

I have the following EVMs:

TAS5720M
TAS5760XX
TAS5766MDCA
PUREPATH-CMB
PP-SALB

I have been granted access to the PPC3 App and have downloaded and installed. But the only EVM App that is available is the I2C Master
My account is rd@gofrontrow.com

Regards,

Roger

0 Shawn Zheng over 7 years ago in reply to ROGER DAVIS

TI__Mastermind 24835 points

Hi Roger,

I will submit a request for the access to TAS5766M app and Learning Board app for your account(rd@gofrontrow.com).

Best regards,

Shawn Zheng

0 ROGER DAVIS over 7 years ago in reply to Shawn Zheng

Prodigy 50 points

Hi Shawn,

I was notified by TI and now have been granted access to the Learning Board EVM, TAS5766M EVM, and the TAS5766M_Dual EVM. However, I was not granted access to the TAS5760xx EVM. Does an EVM app exist for this module? The documentation implies that one does exist. Please respond accordingly.

Best regards,

Roger

0 Shawn Zheng over 7 years ago in reply to ROGER DAVIS

TI__Mastermind 24835 points

Hi Roger,
PPC3 software doesn't apply to TAS5760. You could install ppc software for TAS5760 EVM, which doesn't need any approval. Please find more details in the TAS5760 EVM User's Guide.
Best regards,
Shawn Zheng

0 ROGER DAVIS over 7 years ago in reply to Shawn Zheng

Prodigy 50 points

Hi Shawn,

The PurePath Console (not PPC3) still requires a request to access. I made the request on May 25 but have not been given access yet. Can you please inquire? I am also guessing that there is an EVM app for the TAS5760 that accompanies this too.

Thanks,

Roger

0 Shawn Zheng over 7 years ago in reply to ROGER DAVIS

TI__Mastermind 24835 points

Hi Roger,
Sorry for the delay. I will check with the administrator about this and feeback soon later.
Best regards,
Shawn Zheng

0 ROGER DAVIS over 7 years ago in reply to Shawn Zheng

Prodigy 50 points

Hi Shawn,

I have been out on holiday and am now back. I checked this morning and I still have not been granted access to the PPC software (not PPC3) that is needed to evaluate the TAS5760. Can you please check with the administrator?

Thanks,

Roger

0 Andy Liu (BMS) over 7 years ago in reply to ROGER DAVIS

TI__Guru 52115 points

Hi Roger,

I see you have already been give access to PPC1 (PurePath Console 1).

Actually you can find the PPC1 installer in the same web page where the PPC3 installer is available.

Andy

Audio

Audio forum

PP-SALB-EVM: PP-SALB-EVM PPC3 Software App