ADC12DJ2700EVM: How to get many data using TSW14J57EVM Data Capture Card

Hajun Song

Part Number: ADC12DJ2700EVM
Other Parts Discussed in Thread: TSW14J57EVM

I am using ADC12DJ2700EVM and TSW14J57EVM to capture analog data with sampling rate of 5.4 GHz.

I want to get a lot of data above 65535, but the software for the data capture card only provides maximum data length of 65535.

When I had increased the data length above 65535, error messanges occured.

Is it impossible to get a lot of data above 65535?

over 6 years ago

0 Neeraj Gill over 6 years ago

TI__Mastermind 20541 points

Hi Hajun,

We are looking at your question and will get back to you.

Regards,
Neeraj

0 Jim Brinkhurst1 over 6 years ago in reply to Neeraj Gill

TI__Mastermind 44570 points

Hi Hajun
What revision of TSW14J57EVM do you have?
If it is Revision E there is an updated version of High Speed Data Converter Pro Software/Firmware about to be released that will allow larger captures.
Best regards,
Jim B

0 Hajun Song over 6 years ago in reply to Jim Brinkhurst1

Prodigy 105 points

In my board, "PCB REV B" is written. Is it okay?

Where can I get the upated version?

I had downloaded the software from your website recently and changed the capture length.

However, I failed it.

0 Jim Brinkhurst1 over 6 years ago in reply to Hajun Song

TI__Mastermind 44570 points

Hi Hajun
Unfortunately we don't have support for larger capture depths in the TSW14J57EVM rev B board.
If you obtained this board from a TI salesperson please contact them and request it be replaced with the latest version (Rev E). If you purchased the board from the TI.com store you'll need to purchase a newer version to enabled the latest firmware capabilities.
We are in the process of getting the updated High Speed Data Converter Pro firmware/software loaded to TI.com, but apparently that has not happened yet. Please check back next week. Software version 5.00 or higher should enable the capabilities you need.
I hope this is helpful.
Best regards,
Jim B

0 Hajun Song over 6 years ago in reply to Jim Brinkhurst1

Prodigy 105 points

Oh. It's my mistake. My board is the latest version (Rev. E), but it was mistakenly written incorrectly.

Thank you.

0 Hajun Song over 6 years ago in reply to Jim Brinkhurst1

Prodigy 105 points

I am waiting for the updated High-Speed Data Converter Pro software but it has not yet uploaded to your website.

When will the software be uploaded?

0 Hajun Song over 6 years ago in reply to Jim Brinkhurst1

Prodigy 105 points

I am waiting for the updated High Speed Data Converter Pro software, but it is not yet uploaded to your website.
When can I download the updated HSDC pro software?

0 Jim Brinkhurst1 over 6 years ago in reply to Hajun Song

TI__Mastermind 44570 points

Hi Hajun
There has been some delay getting the updated version of software loaded.
Sorry for the delay.
I will check to see when this is expected to happen and post an update.
Best regards,
Jim B

0 Jim Brinkhurst1 over 6 years ago in reply to Jim Brinkhurst1

TI__Mastermind 44570 points

Hi Hajun
The new version of High Speed Data Converter Pro is now available at the normal download location.
www.ti.com/.../dataconverterpro-sw
Please download and install the new version. It will allow larger capture depths with the TSW14J57EVM Rev E.
Best regards,
Jim B

Data converters

Data converters forum

ADC12DJ2700EVM: How to get many data using TSW14J57EVM Data Capture Card