• State Resolved
  • Locked Locked
  • Replies 6 replies
  • Subscribers 81 subscribers
  • Views 577 views
  • Users 0 members are here
Support feedback
Options
Options
Related

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

Online debug HVMotorCtrl+PFC Kit via CCS4 error

Jimmy Liu81957
Intellectual 310 points

Other Parts Discussed in Thread: TMS320F28035, CONTROLSUITE

Hi,

   I use CCS4 and set Texas Instruments XDS100v1 USB Emulator  and TMS320F28035 on Target Configuration.

  And I populated  [Main]-J9

   When I push debug to connect target ( HVMotorCtrl+PFC Kit ) , I get "  Exception occurred during launch Reason: Failed to load program 'HVACI_Sensorless.out'on any of targets. Reason : The target 'F283X CPU Cycle Accurate Simulator_0/TMS320F283XX_0' could not be found. 

 Could you give me advice???

Regards,

Jimmy     

 

  • 0
    TI__Guru 57255 points

    Jimmy,

    It sounds like your target configuration may be off.  Go to "View->Target Configurations" and make sure that the target configuration you are using is the xds100v1 with a TMS320F28035 and make sure it is set to be the default configuration. Also make sure there are not any project specific target configurations.

    If you feel the target configurations are correct, I would recommend first trying to update Code Composer to the most recent version.  You can do this by going to "Help -> Software Updates -> Check for Updates -> Find and Install...".

    Let us know if this fixes your issue.


    Thank you,
    Brett

  • 0 in reply to Brett Larimore
    Intellectual 310 points

    Brett,

          I update our CCS4(version 4.1.2.00027 ) to last version .

         But I get error message on picture .

        Maybe, I need to re-install it .

    Regards,

    Jimmy

      

  • 0 in reply to Jimmy Liu81957
    Intellectual 310 points

    Brett,

       I do this steps on CCS4 ver1.2.

       Step1 : Launch Selected Configuration

       Step2 : Connect Target

       Step3 : Load Program

       But , I have error when run on target CPU

       I confuse the SW2 on Piccolo F28035 control Card  that define boot mode and jumper [Main]-J9 ,[M3]-J4 on Kit that define JTAG and SCI.

       How do I set up theym when debug it via CCS4???

      Regards,

      Jimmy  

         

  • 0 in reply to Jimmy Liu81957
    TI__Guru 57255 points

    Jimmy,

    Since your original version (4.1.2) is from about a year ago, reinstalling CCS would probably be a good idea if possible. The most recent version can be downloaded from:
    http://processors.wiki.ti.com/index.php/Download_CCS


    Thanks,
    Brett

  • 0 in reply to Brett Larimore
    TI__Guru 57255 points

    Jimmy,

    In order for CCS to connect with the board, [Main]-J9 will need to be populated with a jumper.  Most other jumpers do not really affect whether CCS will connect.

    A full table of the functions of all jumpers/connectors can be found at the end of the following document:
    C:\TI\controlSUITE\development_kits\HVMotorCtrl+PfcKit_v1.6\~Docs\HVMotorCtrl+PFC_HWGuide.pdf


    Thanks,
    Brett

  • 0 in reply to Brett Larimore
    Intellectual 310 points

    Brett,

          I re- install Code Composer Studio Version 4.2.4.00033 to my computer .

         Now , It can work with KIT .

     

    Thanks,

    Jimmy