• State
  • Locked Locked
  • Replies 5 replies
  • Subscribers 82 subscribers
  • Views 797 views
  • Users 0 members are here
Support feedback
Options
Options
Related

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

C2000 Pereipheral explorer kit error

yash dave
Prodigy 50 points

I connected c2000 peripheral explorer kit to my Laptop running with ccs 5.3. F28335 is connected in docking station.

When i am trying to debug code from ccs its giving error like this given below:

C28xx: Error: (Error -150 @ 0x0) One of the FTDI driver functions used during configuration returned a invalid status or an error. (Emulation package 5.0.872.0)
C28xx: Unable to determine target status after 20 attempts
C28xx: Failed to remove the debug state from the target before disconnecting. There may still be breakpoint op-codes embedded in program memory. It is recommended that you reset the emulator before you connect and reload your program before you continue debugging.

please help me to sort out this problem.

  • 0
    Guru 192875 points

    Hi Yash,

    Please check whether your target configuration is properly set. Secondly, also check whether your docking station is properly connected to the pc with respective drivers (check the device manager).

    Regards,

    Gautam

  • 0 in reply to Gautam Iyer
    Prodigy 50 points

    Hi gautam,

    I checked with all settings including target configuration, docking station is properly connected to pc and also checked the device manager also..

    Still its giving me error like this: 

    C28xx: Failed Software Reset: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 5.0.872.0)
    C28xx: Trouble Reading PC Register: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 5.0.872.0)
    C28xx: Trouble Reading Register ST1: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 5.0.872.0)
    C28xx: GEL: Error while executing OnReset(1): target access failed at (ST1&~(0x0100)) [f28335.gel:312] at C28x_Mode() [f28335.gel:38] at OnReset(1) .
    C28xx: Failed Software Reset: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 5.0.872.0)
    C28xx: Trouble Reading PC Register: (Error -1137 @ 0x0) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 5.0.872.0)
    C28xx: Trouble Reading Register ST1: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 5.0.872.0)
    C28xx: GEL: Error while executing OnReset(1): target access failed at (ST1&~(0x0100)) [f28335.gel:312] at C28x_Mode() [f28335.gel:38] at OnReset(1) .
    C28xx: Trouble Writing Memory Block at 0x0 on Page 0 of Length 0x2: (Error -1137 @ 0x6) Device is held in reset. Take the device out of reset, and retry the operation. (Emulation package 5.0.872.0)
    C28xx: GEL: File: C:\Users\admin\Desktop\1-ph PWM\1-ph PWM with ADC in continuous mode (C code)\RamDebug\1_ph_PWM_with_ADC_in_continuous_mode.out: Load failed.

    Please help me to sort out this error.

    Regars,

    yash

  • 0 in reply to yash dave
    Guru 192875 points

    Please check with the health of the controller. Check whether its getting overheated or so.

    Also check the voltage levels on the board.

    Regards,

    Gautam

  • 0 in reply to Gautam Iyer
    Prodigy 50 points

    Hi Gautam,

    I checked a controller and it is getting overheated.

    I dumped a code of 1 -Ph PWM generation which is generated by PSIM softeware. so I checked voltages on EPWM pin of C2000 Experimental board its giving 3.3 voltage level.

    What can i do next?

    Regards,

    Yash

  • 0 in reply to yash dave
    Guru 192875 points

    Hi,

    See now its crystal clear:

    Controller getting overheated means:

    Controller is damaged - you'll have to replace it with a brand new one

    Also check with the regulator IC for overheating!

    Regards,

    Gautam