drvlib file for Piccolo controller TMS320F28030

Hi Bipin,

Did you check the controlSuite/motorware for the same?

Regards,
Gautam

Sir,

I Have Checked It but Didnt get it,

Can You Please Give the Path or some file .

Regards,
Bipin

Sorry Bipin, we'll have to wait for Tiers to comment on this further.
Be patient :)

Regards,
Gautam

We do not have a driverlib available for F2803x. We do have bitfields and examples in controlSUITE which use these bitfields.

Regards,
sal

Thank You sir,

 I am facing another Problem  i just started the to develop the firmware using the base example.every time i got below error. please give remedy for that

 line 48: error #10099-D: program will not fit into available
    memory.  placement with alignment fails for section ".text" size 0x2b12 .
    Available memory ranges:
    FLASH        size: 0x1000       unused: 0xe56        max hole: 0xe56 

Linker File :--   F28030.cmd   

Stack Size :- 800

Heap Size :- 800

 

 

SECTIONS

{

/* Allocate program areas: */

.cinit : > FLASHA PAGE = 0

.pinit : > FLASHA, PAGE = 0

.text : > FLASHA PAGE = 0

codestart : > BEGIN

PAGE = 0

ramfuncs :

LOAD = FLASHD,

RUN = RAML0,

LOAD_START(_RamfuncsLoadStart),

LOAD_END(_RamfuncsLoadEnd),

RUN_START(_RamfuncsRunStart),

PAGE = 0

csmpasswds : > CSM_PWL_P0

PAGE = 0

csm_rsvd : > CSM_RSVD

PAGE = 0

/* Allocate uninitalized data sections: */

.stack : > RAMM0 PAGE = 1

.ebss : > RAML2

PAGE = 1

.esysmem : > RAML2

PAGE = 1

/* Initalized sections go in Flash */

/* For SDFlash to program these, they must be allocated to page 0 */

.econst : > FLASHA

PAGE = 0

.switch : > FLASHA

PAGE = 0

/* Allocate IQ math areas: */

IQmath : > FLASHA

PAGE = 0 /* Math Code */

IQmathTables : > IQTABLES,

PAGE = 0, TYPE = NOLOAD

 

 

 

 

MEMORY

{

PAGE

0:

/* Program Memory */

/* Memory (RAM/FLASH/OTP) blocks can be moved to PAGE1 for data allocation */

RAML0 : origin = 0x008000, length = 0x000800

/* on-chip RAM block L0 */

RAML1 : origin = 0x008800, length = 0x000400

/* on-chip RAM block L1 */

OTP : origin = 0x3D7800, length = 0x000400

/* on-chip OTP */

FLASHD : origin = 0x3F4000, length = 0x001000

/* on-chip FLASH */

FLASHC : origin = 0x3F5000, length = 0x001000

/* on-chip FLASH */

FLASHA : origin = 0x3F7000, length = 0x000F80

/* on-chip FLASH */

CSM_RSVD : origin = 0x3F7F80, length = 0x000076

/* Part of FLASHA. Program with all 0x0000 when CSM is in use. */

BEGIN : origin = 0x3F7FF6, length = 0x000002

/* Part of FLASHA. Used for "boot to Flash" bootloader mode. */

CSM_PWL_P0 : origin = 0x3F7FF8, length = 0x000008

/* Part of FLASHA. CSM password locations in FLASHA */

IQTABLES : origin = 0x3FE000, length = 0x000B50

/* IQ Math Tables in Boot ROM */

IQTABLES2 : origin = 0x3FEB50, length = 0x00008C

/* IQ Math Tables in Boot ROM */

IQTABLES3 : origin = 0x3FEBDC, length = 0x0000AA

/* IQ Math Tables in Boot ROM */

ROM : origin = 0x3FF27C, length = 0x000D44

/* Boot ROM */

RESET : origin = 0x3FFFC0, length = 0x000002

/* part of boot ROM */

VECTORS : origin = 0x3FFFC2, length = 0x00003E

/* part of boot ROM */

Bipin, which sample code are you referring to?

Gautam thank for reply . i herewith my .map File MEMORY CONFIGURATION
name origin length used unused attr fill
---------------------- -------- --------- -------- -------- ---- --------
PAGE 0: RAML0 00008000 00000800 0000001f 000007e1 RWIX
RAML1 00008800 00000400 00000000 00000400 RWIX
OTP 003d7800 00000400 00000000 00000400 RWIX
FLASHD 003f4000 00001000 0000001f 00000fe1 RWIX
FLASHC 003f5000 00001000 00000000 00001000 RWIX
FLASHA 003f7000 00000f80 00000ebf 000000c1 RWIX
CSM_RSVD 003f7f80 00000076 00000076 00000000 RWIX
BEGIN 003f7ff6 00000002 00000002 00000000 RWIX
CSM_PWL_P0 003f7ff8 00000008 00000008 00000000 RWIX
IQTABLES 003fe000 00000b50 00000000 00000b50 RWIX
IQTABLES2 003feb50 0000008c 00000000 0000008c RWIX
IQTABLES3 003febdc 000000aa 00000000 000000aa RWIX
ROM 003ff27c 00000d44 00000000 00000d44 RWIX
RESET 003fffc0 00000002 00000000 00000002 RWIX
VECTORS 003fffc2 0000003e 00000000 0000003e RWIXPAGE 1:
BOOT_RSVD 00000000 00000050 00000000 00000050 RWIX
RAMM0 00000050 000003b0 00000320 00000090 RWIX
RAMM1 00000400 00000400 00000000 00000400 RWIX
DEV_EMU 00000880 00000105 00000004 00000101 RWIX
SYS_PWR_CTL 00000985 00000003 00000003 00000000 RWIX
FLASH_REGS 00000a80 00000060 00000008 00000058 RWIX
CSM 00000ae0 00000010 00000010 00000000 RWIX
ADC_RESULT 00000b00 00000020 00000020 00000000 RWIX
CPU_TIMER0 00000c00 00000008 00000008 00000000 RWIX
CPU_TIMER1 00000c08 00000008 00000008 00000000 RWIX
CPU_TIMER2 00000c10 00000008 00000008 00000000 RWIX
PIE_CTRL 00000ce0 00000020 0000001a 00000006 RWIX
PIE_VECT 00000d00 00000100 00000100 00000000 RWIX
CLA1 00001400 00000080 00000040 00000040 RWIX
ECANA 00006000 00000040 00000000 00000040 RWIX
ECANA_LAM 00006040 00000040 00000000 00000040 RWIX
ECANA_MOTS 00006080 00000040 00000000 00000040 RWIX
ECANA_MOTO 000060c0 00000040 00000000 00000040 RWIX
ECANA_MBOX 00006100 00000100 00000000 00000100 RWIX
COMP1 00006400 00000020 00000011 0000000f RWIX
COMP2 00006420 00000020 00000011 0000000f RWIX
COMP3 00006440 00000020 00000011 0000000f RWIX
EPWM1 00006800 00000040 0000003a 00000006 RWIX
EPWM2 00006840 00000040 0000003a 00000006 RWIX
EPWM3 00006880 00000040 0000003a 00000006 RWIX
EPWM4 000068c0 00000040 0000003a 00000006 RWIX
EPWM5 00006900 00000040 0000003a 00000006 RWIX
EPWM6 00006940 00000040 0000003a 00000006 RWIX
EPWM7 00006980 00000040 0000003a 00000006 RWIX
ECAP1 00006a00 00000020 00000000 00000020 RWIX
EQEP1 00006b00 00000040 00000000 00000040 RWIX
LINA 00006c00 00000080 0000004a 00000036 RWIX
GPIOCTRL 00006f80 00000040 00000040 00000000 RWIX
GPIODAT 00006fc0 00000020 00000020 00000000 RWIX
GPIOINT 00006fe0 00000020 0000000c 00000014 RWIX
SYSTEM 00007010 00000020 00000020 00000000 RWIX
SPIA 00007040 00000010 00000000 00000010 RWIX
SCIA 00007050 00000010 00000010 00000000 RWIX
NMIINTRUPT 00007060 00000010 00000010 00000000 RWIX
XINTRUPT 00007070 00000010 00000010 00000000 RWIX
ADC 00007100 00000080 00000050 00000030 RWIX
SPIB 00007740 00000010 00000000 00000010 RWIX
I2CA 00007900 00000040 00000000 00000040 RWIX
RAML2 00008c00 00000400 000000a4 0000035c RWIX
PARTID 003d7e80 00000001 00000001 00000000 RWIX
FLASHB 003f6000 00001000 00000000 00001000 RWIX
CSM_PWL 003f7ff8 00000008 00000008 00000000 RWIX
SECTION ALLOCATION MAP output attributes/
section page origin length input sections
-------- ---- ---------- ---------- ----------------
.cinit 0 00000000 000000d8 FAILED TO ALLOCATE
.pinit 0 003f7000 00000000 UNINITIALIZED
ramfuncs 0 003f4000 0000001f RUN ADDR = 00008000
003f4000 0000001b DSP2803x_SysCtrl.obj (ramfuncs)
003f401b 00000004 DSP2803x_usDelay.obj (ramfuncs)

thank you for reply
i used above Linker file & build my project then i m getting below error
error #10099-D: program will not fit into available
memory. placement with alignment/blocking fails for section ".cinit" size
0xd8 page 0. Available memory ranges:
FLASHA size: 0xf80 unused: 0xca max hole: 0xca

When i am using TMS320F2810 I used F2810_FlashLinker.cmd .

\controlSUITE\device_support\f2803x\v130\DSP2803x_examples_ccsv5\timed_led_blink sample code for reference.

Can i know why it giving this error ? when i checked my FLASH memory in Section wise i have enoug memory

Sir,
LED BLinking Programme for just testing purpose of my hardware.Actual i m developing algorith for PMSM motor with Piccolo controller (tms 320F28030) i had compeleted PWM ,SCI,ADC, function now trying to include FOC for same but getting the above problem as i discused

Already we have developed firmware in TMS 320F2810. working since 10years.

Understand! But it seems sample code itself is not compiling properly, which is a big question in itself! Which CCS version are you using?

Code Composer Studio Version: 5.2.0.00069 Compiler TI v6.1.0

I changed in linker file memory allocationMEMORY{PAGE 0: /* Program Memory *
/// FLASHD : origin = 0x3F4000, length = 0x001000 /* on-chip FLASH */
// FLASHC : origin = 0x3F5000, length = 0x001000 /* on-chip FLASH */
FLASHD_C : origin = 0x3F4000, length = 0x002000 /* on-chip FLASH */
SECTIONS{ /* Allocate program areas: */
.cinit : > FLASHD_C PAGE = 0
.pinit : > FLASHD_C, PAGE = 0
.text : > FLASHD_C PAGE = 0

but when i run the programme CPU hangs

Bipin, first of all understand linking: processors.wiki.ti.com/.../C28x_Compiler_-_Understanding_Linking

Gautam Thanks!!!!!!!!!!!!!!!!!!!!