DRV8300: Looking for to find coworkers

zbyno brudny32

Part Number: DRV8300
Other Parts Discussed in Thread: , C2000WARE-MOTORCONTROL-SDK, C2000WARE

Tool/software:

I am looking for somebody who will be interested in a new method of BLDC-control like in this my published article

www.researchgate.net/.../376457774_A_new_method_at_the_180-control_5-SVPWM_of_BLDC_part_2 + many others on this portal Researchgate.net

please answer me on address zbyno.brudny@centrum.cz

regards

10 months ago

0 Ryan Kehr 10 months ago

TI__Guru 55615 points

ZB,

This forum is meant to answer technical questions for TI BLDC motor driver products. I see you mentioned the DRV8300 in the post. Is there a specific question the team can help you out with on the device itself or other device in our portfolio?

Regards,

Ryan

0 zbyno brudny32 10 months ago in reply to Ryan Kehr

Intellectual 260 points

Hi Ryan

My post was not only mentioned for the usage of DRV8300U but this driver can be used for this new algorithm in the future. To whom must I send my appeal for collaboration about my new control algorithm of the BLDC-control?

best regards

zbyno brudny

0 Ryan Kehr 10 months ago in reply to zbyno brudny32

TI__Guru 55615 points

Zbyno,

I will move this to our C2000 team that specializes in algorithm development.

This forum is for help on the driver side.

Regards,

Ryan

0 Yanming Luo 10 months ago in reply to Ryan Kehr

TI__Guru** 115430 points

You may take a look at the lab for the C2000 devices in motor control SDK. The universal motor control lab is available in the current MCSDK, which can support a set of hardware kits and control algorithms for BLDC/PMSM drive. The kits include LAUNCHXL-F280025C, LAUNCHXL-F280039C, LAUNCHXL-F2800137 with a few sets of DRV inverter board BOOSTXL-DRV8323RS, BOOSTXL-DRV8323RH, DRV8353Rx-EVM, BOOSTXL-3PHGANINV, DRV8316REVM, or DRV8329AEVM for low voltage motor. The control algorithms include sensorless InstaSPIN-FOC with FAST, Sensorless-FOC with eSMO, Sensored-FOC with incremental encoder, Sensored-FOC with hall sensor. You can refer to the device peripherals (ePWM, ADC, eQEP, or eCAP) configuration for motor control with the other C2000 devices and DRV boards including DRV8300 EVM.

C2000WARE-MOTORCONTROL-SDK: https://www.ti.com/tool/C2000WARE-MOTORCONTROL-SDK

Universal Project and Lab User’s Guide: https://www.ti.com/lit/spruj26

Example lab project at the folder: C:\ti\c2000\C2000Ware_MotorControl_SDK_<version>\solutions\universal_motorcontrol_lab\f28002x

or C:\ti\c2000\C2000Ware_MotorControl_SDK_<version>\solutions\universal_motorcontrol_lab\f28003x

or C:\ti\c2000\C2000Ware_MotorControl_SDK_<version>\solutions\universal_motorcontrol_lab\f280013x

0 zbyno brudny32 10 months ago in reply to Yanming Luo

Intellectual 260 points

Thank you Yanming Luo

But my concept is a little different i measure two phase currents, which carry half of the whole motor current and so i want to compute the actual angle. See in: https://www.researchgate.net/publication/376457774_A_new_method_at_the_180-control_5-SVPWM_of_BLDC_part_2

regards

zbyno

0 Yanming Luo 10 months ago in reply to zbyno brudny32

TI__Guru** 115430 points

Sorry. If the reference algorithms like sinusoidal FOC or trapezoidal control in the example lab can't meet your requirements, you have to design the algorithm by yourself or try to find any third party to get the algorithm.

0 zbyno brudny32 10 months ago in reply to Yanming Luo

Intellectual 260 points

yes, I understood. Thank you.

what a pity... I thought that it would be interesting for your developers.

regards

zbyno

Motor drivers

Motor drivers forum

DRV8300: Looking for to find coworkers