Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.

  • State Resolved
  • Locked Locked
  • Replies 7 replies
  • Subscribers 65 subscribers
  • Views 222 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

Original question:

TL7705B: SENSE-pin internal resistance R1 R2 values?

TL7705B: What is the input current of SENSE and /RESIN terminals?

Kazuya Nakai59
Guru 20780 points
Part Number: TL7705B
Other Parts Discussed in Thread: TL7733B

Hello guys,

One of my customers is evaluating TL7705B for their new products.

As this moment, they have the following questions.

Could you please give me your reply?

Q1.  What is the input current of SENSE terminal for TL7705B and /RESIN terminal?

Q2. What is the reason of no definition of input current of SENSE (for TL7705B and TL7733B) and /RESIN terminals?

Q3. The resistor values of R1/R2 in the block diagram in TL7705B datasheet were eliminated when the datasheet version was updated from SLVS037M to SLVS037N.

       What is the reason of the elimination?

Your reply would be much appreciated.

Best regards,

Kazuya.

  • 0
    TI__Mastermind 40675 points

    Hi Kazuya-san,

    Q1.  What is the input current of SENSE terminal for TL7705B and /RESIN terminal?

    TL7705B: R1 = 23kOhm, R2 = 10kOhm, Vx = 1.43V.  

    Q2. What is the reason of no definition of input current of SENSE (for TL7705B and TL7733B) and /RESIN terminals?

    I am not clear about this question.  I was able to find the input current for SENSE and /RESIN in the datasheet.

    Q3. The resistor values of R1/R2 in the block diagram in TL7705B datasheet were eliminated when the datasheet version was updated from SLVS037M to SLVS037N.  What is the reason of the elimination?

    The datasheet format was changed from revision M to revision N where revision N is the updated datasheet version from M.  It may have been an oversight that the resistor values were omitted from the datasheet.  Here is what I found in the database:

    I hope I have answered all of the questions to your satisfaction.  If there are no further questions, please click on "resolved" to close the thread.  Thank you!

    Ben

  • 0 in reply to Ben C
    Guru 20780 points

    Hi Ben,

    Thank you very much for your reply. I understood.

    Also I'm sorry about Q2. I overlooked the input current of /RESIN.

    The customer wants TI to add R1 and R2 resistor value to the new datasheet.

    Could you please add these values at the datasheet update timing?

    Thank you again and best regards,

    Kazuya.

  • 0 in reply to Kazuya Nakai59
    TI__Mastermind 40675 points

    Hi Kazuya-san,

    Yes, we are planning on adding the R1 and R2 resistor values into the data sheet during our next revision cycle.

    Go ahead and close the thread if there are no further questions.  Have a great weekend!

    Ben

  • 0 in reply to Ben C
    TI__Mastermind 40675 points

    Hi Kazuya-san,

    If there there are no further questions, please close the thread by clicking on "resolved".  Thanks and good luck to you!

    Ben

  • 0 in reply to Ben C
    TI__Mastermind 40675 points

    HI Kazuya-san,

    Just following up with you to see if you have any additional questions for me.  If not, can you close the thread.  Thanks and have a great weekend!

    Ben

  • 0 in reply to Ben C
    Guru 20780 points

    Hello Ben,

    I'm sorry to be late response because I was taking summer day off.

    Thank you very much for your strong supports.

    Best regards,

    Kazuya.

  • 0 in reply to Kazuya Nakai59
    TI__Mastermind 40675 points

    Hi Kazuya-san,

    Glad to be help!  Good luck to you!

    Ben