UCC28700-Q1: UCC28700-Q1: reference design

ouadif abdelhalim

Part Number: UCC28700-Q1
Other Parts Discussed in Thread: UCC28700, , UCC28722

Hello,

I downloaded the reference design from your website, and when I made some modifications based on my specifications, the simulation stopped working after 5ms. (https://www.ti.com/lit/tsc/slum619)

Can you help me please?

over 1 year ago

0 Mike O' over 1 year ago

TI__Guru 74875 points

Hello,

I am evaluating your issue and will get back to you shortly.

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

Hello,

Thank you

+1 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Hello,

I would double check your design to see if the transformer turns ratio, output capacitance and other electrical components are setup correctly.

The following link will bring you to an application note that describes how to design with and setup this device.

https://www.ti.com/lit/pdf/slua653

There is an excel tool that goes along with the above application note that you can use to double check your design as well. You can find a link to this excel tool below.

https://www.ti.com/lit/zip/sluc408

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

Hello,

Okay i will check it, this is my design

1488.Controller design (1) (1).pdf

0028.Flyback-400V.TSC

0 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Hello,

Thanks for letting me know.

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

Hello Mike,

I designed the controller according to the application note (https://www.ti.com/lit/pdf/slua653) , but it's stop simulation again on 5ms

Thank's

+1 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Hello,

Thanks for letting me know.

In regards to shutting down. The simulation may be shutting down due to an over voltage protection (OVP), over current protection (OCP) or input under voltage fault.

The following ink will bring you to an application note that describes primary fault sensing works. The most common issues with this technique and how to resolve them. The UCC28700 uses this fault sensing technique and I believe this application note will help you troubleshoot and resolve your shut down issues.

https://www.ti.com/lit/pdf/sluaac5

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

Hello Mike,

Thank you for your assistance.

0 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Hello,

I was glad to help.

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

Hello Mike O',

I have a question, Is it possible for the UCC28700-Q1 to regulate the output voltage to 12 volts when the input voltage varies from 400 to 800 volts DC?

0 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Hello,

The UCC28700-Q1 should be able to regulate the output voltage with up to a 3 to 1 variation in input voltage.

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

what's kind of flyback controller can regulate output voltage with up to 400 variation in input voltage ?

0 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Non that I know of at this time.

3 to 1 is typical, up to 5 to 1 can be accomplished with careful consideration. After that you run into limits with duty cycle.

With DCM flyback controllers you can go up to a 9 to 1 variation before running into limits with leading edge blanking.

The follow link will bring you to an application note that describes how to design a flyback with a 9 to 1 input range using the UCC28722 flyback controller. The controller is very similar to the UC28700-Q1 and the same technique should work with the UCC28700-Q1.

https://www.ti.com/lit/an/slua781/slua781.pdf?ts=1683723544302&ref_url=https%253A%252F%252Fwww.ti.com%252Fproduct%252FUCC28722%253FkeyMatch%253DUCC28722%2526tisearch%253Dsearch-everything%2526usecase%253DGPN

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

what do you mean by 3 to 1 ?

that the controller can regulate 3 variations of input voltage or what?

0 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Hello,

If your input varies 3 to 1 that means input voltage could change 3 to 1.

For example if your input was 300V. You could design it so the input range could from 300 to 100 V.

Regards,

0 Mike O' over 1 year ago

TI__Guru 74875 points

That is correct.

Regards,

0 ouadif abdelhalim over 1 year ago in reply to Mike O'

Prodigy 25 points

Hello,

So the controller can regulate input variation from (1): 800 to 533V or

(2): 800 to 255 V

533 come from (800-800/3)=533

255 come from 800/3=255

0 Mike O' over 1 year ago in reply to ouadif abdelhalim

TI__Guru 74875 points

Hello,

1 to 1/3 times should be O.K.

Regards,

Power management

Power management forum

UCC28700-Q1: UCC28700-Q1: reference design