FusionParamReader : error An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)

Vikas Sharma

Prodigy 60 points

Other Parts Discussed in Thread: USB-TO-GPIO2

Hello,

I have installed Fusion Digital Designer 7.9.1

With GUI i am able to read VOUT

But with CLI, i am getting error while reading Vout.

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 126 --rail 1 OPERATION VOUT_COMMAND READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 27 --rail 1 OPERATION VOUT_COMMAND READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 54 --rail 1 OPERATION VOUT_COMMAND READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 36 --rail 1 OPERATION VOUT_COMMAND READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 1B --rail 1 OPERATION VOUT_COMMAND READ_VOUT
FusionParamReader: command line error: invalid value: 1B for --address

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 0x1B --rail 1 OPERATION VOUT_COMMAND READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 18 --rail 1 OPERATION VOUT_COMMAND READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 18 --rail 1 OPERATION READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 18 --rail 1 READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>
C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 18 --rail 1 READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)
FusionParamReader: FAIL: exiting due to error

C:\Program Files (x86)\Texas Instruments\Fusion Digital Power Designer\bin>FusionParamReader --address 27 --rail 1 READ_VOUT
FusionParamReader: An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)

No clue why CLI is not working.

I need commands for:

Read - READ_VOUT

Write/set Vout_Command

& Save

over 2 years ago

0 Sean Xu over 2 years ago

TI__Genius 14580 points

Hello,

What is CLI? can you share the screen shot?

Regards

0 Vikas Sharma over 2 years ago in reply to Sean Xu

Prodigy 60 points

CLI command line - FusionParamReader this command can be used to read parameter.

0 Sean Xu over 2 years ago in reply to Vikas Sharma

TI__Genius 14580 points

I will check with the team, and let you know shortly

0 Vikas Sharma over 2 years ago in reply to Sean Xu

Prodigy 60 points

Hello Sean,

Any update.

Any other way to read V_OUT & write VOUT COMMAND register from command (PBBus/I2C)?

0 Ankit Kumar over 2 years ago in reply to Vikas Sharma

TI__Prodigy 60 points

Hello Vikas,

You mentioned that you are able to read it from GUI. May you send a screenshot of that? How are you reading it?

0 Vikas Sharma over 2 years ago in reply to Ankit Kumar

Prodigy 60 points

Hello Ankit,

Screenshots:

Need to read Vout and Set CommandVolt.

0 Vikas Sharma over 2 years ago in reply to Vikas Sharma

Prodigy 60 points

Hello,

I am using USB to GPIO2

Command line not working,

APIs not working..

Any idea, I am stuck.

-----

from TIDP.SAA import TIBusAdapters

Adapters = TIBusAdapters()

n = Adapters.Discover()

print(n)

==> 0

0 Ankit Kumar over 2 years ago in reply to Vikas Sharma

TI__Prodigy 60 points

Hello Vikas.

Thank you for your patience. Please help me with the following things --

1. Which topology are you using? Is your firmware build over any of the TI sample firmware code that we provide? If yes, may you share the link from where you downloaded firmware.

0 Ankit Kumar over 2 years ago in reply to Ankit Kumar

TI__Prodigy 60 points

I wanted to have a crude replicate of your setup. Firmware topology name is needed for that.

0 Ankit Kumar over 2 years ago in reply to Vikas Sharma

TI__Prodigy 60 points

Hello Vikas,

Please try the following and let me know if it works --

NOTE:
Path will be dependent on where you installed the Fusion GUI.

Make sure the device address (126 in your case) that you are passing is correct.

0 Vikas Sharma over 2 years ago in reply to Ankit Kumar

Prodigy 60 points

Hello Ankit,

It did not work.

I am using USBto GPIO2

I tried with APIs too. That also not working

Address is 27 & FUSION GUI is working.

0 Vikas Sharma over 2 years ago in reply to Sean Xu

Prodigy 60 points

Hello Sean,

Please check with team, why this is not working?

I am using USB to GPIO2.

API also not working.

Any python code to read V_OUT & Set command_volt.

If this works, that will solve my porblem.

FusionParamReader --address 27 --rail 1 READ_VOUT

0 Ankit Kumar over 2 years ago in reply to Vikas Sharma

TI__Prodigy 60 points

Hi Vikas,

Please share your email id.

0 Vikas Sharma over 2 years ago in reply to Ankit Kumar

Prodigy 60 points

Hi Ankit

vikas.sharma@vvdntech.in

0 Vikas Sharma over 2 years ago in reply to Vikas Sharma

Prodigy 60 points

For Info:

In latest Fusion designer software, usb2gpiov2.dll in not working with CLI (in bin folder)

In latest Fusion studio software, Commands are working but TI Part number i am using is not supported. ic_device_id scan code is not supported.

Hello Ankit,

Any new update!

Thanks for help.

0 Vikas Sharma over 2 years ago in reply to Vikas Sharma

Prodigy 60 points

Hello TI team

CLI still not working. Please help here

0 Vikas Sharma over 1 year ago in reply to Vikas Sharma

Prodigy 60 points

Now sure, how this will be sorted

Ti team plz check and help

+1 Anne Ngo77 over 1 year ago in reply to Vikas Sharma

TI__Genius 9310 points

Hi, Vikas,

Please use the latest beta TI-Fusion-Digital-Power-Designer-7.9.8.zip that support USB-to-GPIO2 in command line tools.

Regards,

Anne Ngo

Texas Instruments

0 Vikas Sharma over 1 year ago in reply to Anne Ngo77

Prodigy 60 points

Hi Anne,

Thanks for your reply.

We are unable to download from this link. It seems broken.

Please check.

0 Anne Ngo77 over 1 year ago in reply to Vikas Sharma

TI__Genius 9310 points

Hi, Vikas,

Please use either Google Chrome, Firefox, or Microsoft Edge browsers. Right click the link to copy the link address, then paste the link address to the URL browser.

Regards

Anne Ngo

Texas Instruments

0 Vikas Sharma over 1 year ago in reply to Anne Ngo77

Prodigy 60 points

He Anne,

I have tried C-Chrome, direct also & copied link also & paste in browser.

http://software-dl.ti.com/analog/analog_public_sw/fusion/sample-builds/TI-Fusion-Digital-Power-Designer-7.9.8.zip

software-dl.ti.com/.../TI-Fusion-Digital-Power-Designer-7.9.8.zip

Even tried in mobile, Upto 2mb only it is downloaded.

Please check above link or upload somewhere else; without zip it.

Able to download below link (earlier shared by TI team) (CLI not worked in this)

http://software-dl.ti.com/analog/analog_public_sw/fusion/TI-Fusion-Digital-Power-Designer-7.4.1.exe

0 Vikas Sharma over 1 year ago in reply to Vikas Sharma

Prodigy 60 points

Hi Anne,

Thanks for your help.

Now Fusion Power Designer CLIs commands are working USB-to-GPIO2.

It took bit long, but my problem has been solved now.

Really appreciate!

Power management

Power management forum

FusionParamReader : error An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)