Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.

  • State Resolved
  • Locked Locked
  • Replies 5 replies
  • Answers 1 answer
  • Subscribers 64 subscribers
  • Views 516 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

Original question:

TPS2544: Can TPS2544 adjust current by parallel RLIM resistor after device enable ?

TPS2546: USB3.0 can able to be detect after wake up from S3.

Shaquille Chen
Intellectual 1770 points
Part Number: TPS2546
Other Parts Discussed in Thread: TUSB522P, TPS2001D

Hi Team,

Customer are using TPS2546.

They found that when system wake up from S3, USB3.0 device are not able to be detect.

Then they short the IN and OUT on TPS2546 then this issue gone.

Do we have such experience? What’s the possible root cause?

Thanks

Shaq.

  • 0
    TI__Mastermind 29525 points
    Hello Shaq,

    What are the levels of the CTL pins when the system is in sleep to when the system is in wake? Also, do you have any waveforms for the failure?
  • 0 in reply to Adam Mc Gaffin
    TI__Mastermind 29525 points
    Hello Shaq,

    I am going to close this item. Feel free to respond to this ticket or create a new one if you have any questions.
  • 0 in reply to Adam Mc Gaffin
    TI__Intellectual 1770 points

    Hi Adam,

    Here is update. There are two port on costume system. 

    port A: TUSB2546 + TUSB522P

    portB: TUSB522P + TPS2001D

    We did some experiment found that USB3.0 cannot work is something to do with Vbus.

    If customer short Vbus to connector ( bypass TUSB2546), this issue was gone.

    This issue was gone when CTL does not change setting in different mode.

    Customer issue condition on port A:

    1. reboot system

    2. USB 3.0 flash plug in. It was been detected and shown on device manager.

    3. system enter S3 ( sleep mode)

    4. system wake up from S3, USB 3.0 flash not able to detect by system.

    5. Unplug then plug in again are not able to been detect.

    Customer issue condition on port B:

    1. refresh or reboot system

    2. USB 3.0 flash plug in. It was been detected and shown on device manager.

    3. system enter S3 ( sleep mode)

    4. system wake up from S3, USB 3.0 flash not able to detect by system.

    5. Unplug then plug in again, USB 3.0 flash are able to been detect.

    This figure is shown when device enter S3.

    This picture shown device wake up from S3 but not able to get USB3.0 signal.

    Thanks

    Shaq.

  • 0 in reply to Shaquille Chen
    TI__Mastermind 29525 points
    Hello Shaq,

    When transitioning from one charging mode to another, per the USB spec VBUS is required to discharge for a specific amount of time. However, if the host tries to negotiate on the USB DP/DM lines before 5V has been presented back on VBUS, than there will be an issue. I do not believe the problem is due to the TPS2546 handling of VBUS, but how the host system is potentially handling the USB lines.
  • 0 in reply to Adam Mc Gaffin
    TI__Intellectual 1770 points
    Hi Adam,

    We figure out that host should send warm reset after Vbus temporary disappear.

    Thanks
    Shaq.