AM62A7: OV2312

Betul Aktepe

Other Parts Discussed in Thread: AM623, SK-AM62A-LP, AM62A7, AM62A3

Can we use OV2312 directly with MIPI CSI, if not can we also use it with Link V3 SerDes, without any modification on source?

Last question is can we use 2 OV2312 at the same time, both for MIPI CSI and V3Link SerDes.

9 months ago

0 Betul Aktepe 9 months ago

Prodigy 230 points

Next question is can we use AM6231ASGGGAALW to run this sensor?

Thanks...

0 Jianzhong Xu 9 months ago in reply to Betul Aktepe

TI__Guru 61400 points

Hello,

Betul Aktepe said:
Can we use OV2312 directly with MIPI CSI, if not can we also use it with Link V3 SerDes, without any modification on source?

It depends on the camera module with the OV2312 sensor. If the camera module has the FPD-Link interface, like Leopard Imaging LI-OV2312-FPDLINKIII-110H, you can use the V3Link SerDes to connect to AM62A EVM. If the camera module has a MIPI CSI interface (like the 22-pin FPC connector), then you can connect it directly to AM62A EVM. Please refer to the AM62A Linux Academy, using camera, for more details.

Betul Aktepe said:
Last question is can we use 2 OV2312 at the same time, both for MIPI CSI and V3Link SerDes.

Yes, you can, but only through V3 Link SerDes (or FPD-Link SerDes). Again, please refer to the above link, especially the section for FPD-Link camera.

Betul Aktepe said:
Next question is can we use AM6231ASGGGAALW to run this sensor?

No, the AM623 device doesn't have an ISP which is required to process raw data from OV2312. You'll need to use AM62A family of devices.

Regards,

Jianzhong

0 Betul Aktepe 9 months ago in reply to Jianzhong Xu

Prodigy 230 points

Thanks for your clarification, I understand all, actually my question has missing points.

1- If we can design a camera module with MIPI CSI connector, can we connect it to directly SK-AM62A-LP, than without any modification on driver can it work?

2- Yes Our aim is to use 2 OV2312 with SerDes.

3- Let me ask new question than, can we use 2 OV2312 + 1 IMX390 with V3 Link SerDes with AM62A3 (or AM62A7) at the same time, because in AM62A Linux Academy, using camera part 4 IMX219 is used.

Thanks for your help and reply.

Regards

+1 Jianzhong Xu 9 months ago in reply to Betul Aktepe

TI__Guru 61400 points

Betul Aktepe said:
1- If we can design a camera module with MIPI CSI connector, can we connect it to directly SK-AM62A-LP, than without any modification on driver can it work?

Yes, it can work. Sensor driver is independent of HW interface. You only need to change the device tree overlay for direct CSI connection.

Betul Aktepe said:
3- Let me ask new question than, can we use 2 OV2312 + 1 IMX390 with V3 Link SerDes with AM62A3 (or AM62A7) at the same time, because in AM62A Linux Academy, using camera part 4 IMX219 is used.

Yes, this should work.

0 Betul Aktepe 9 months ago in reply to Jianzhong Xu

Prodigy 230 points

Hi Jianzhong Xu, thanks for your help. We are going to run this.

Processors

Processors forum

AM62A7: OV2312