DVR_RDK2.8 Capture

Shary Li

Intellectual 925 points

Other Parts Discussed in Thread: TVP5158, TVP7002

Hi, I use RDK2.8 and the board is ours.

Now I don't want to use TVP5158, and directly sent the handled data to VIP0 and then nsf.

I try to delete any code about TVP5158, but it does not seem to work.

How can I modify?

over 13 years ago

0 Brijesh Jadav over 13 years ago

TI__Guru**** 494515 points

Hi,

Try setting gVcapModuleContext.vcapConfig.enableConfigExtVideoDecoder flag to FALSE..

Regards,

Brijesh Jadav

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

Thanks very much for your replay.

I set the param accroding to your advice.But the error is as following:

Opened file [/opt/VID_CH00.yuv] for writing CH0
open the file
[host] MCFW_IPCFRAMES:VcapVenc_ipcFramesSendRecvFxn:Entered... [m3vpss ] 36347: CAPTURE: Create in progress !!!
[m3vpss ] 36376: CAPTURE: VIP0 PortA capture mode is [16-bit, Non-mux Discrete Sync - HSYNC_VSYNC] !!!
[m3vpss ] 36376: Assertion @ Line: 745 in links_m3vpss/capture/captureLink_drv.c: pInst->captureVipHandle != NULL : failed !!!

0 Badri Narayanan over 13 years ago in reply to Shary Li

TI__Guru 59700 points

Can you share your captureLink create params

0 Badri Narayanan over 13 years ago

TI__Guru 59700 points

Pls try setting capturePrm.fakeHd = TRUE in your capturePrms. Also is SYSTEM_USE_VIDEO_DECODER define enabled in system_debug.h ? If it is enabled, pls rebuild rdk with SYSTEM_USE_VIDEO_DECODER disabled.

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

Thanks very much for your reply.

If SYSTEM_USE_VIDEO_DECODER = FALSE, the error is:

[host] MCFW_IPCFRAMES:VcapVenc_ipcFramesSendRecvFxn:Entered... [m3vpss ] 92868: CAPTURE: Create in progress !!!
[m3vpss ] 92898: CAPTURE: VIP0 PortA capture mode is [ 8-bit, Pixel-mux Embedded Sync] !!!
[m3vpss ] 92898: Assertion @ Line: 742 in links_m3vpss/capture/captureLink_drv.c: pInst->captureVipHandle != NULL : failed !!!If SYSTEM_USE_VIDEO_DECODER = TRUE, the error is:

[m3vpss ] 24667: CAPTURE: VIP0 PortA capture mode is [ 8-bit, Pixel-mux Embedded Sync] !!!
[m3vpss ] 24667: Assertion @ Line: 742 in links_m3vpss/capture/captureLink_drv.c: pInst->captureVipHandle != NULL : failed !!!

0 Shary Li over 13 years ago in reply to Shary Li

Intellectual 925 points

The result is same.

0 Badri Narayanan over 13 years ago in reply to Shary Li

TI__Guru 59700 points

Dont set SYSTEM_USE_VIDEO_DECODER to FALSE. I meant undefine it if it is defined

/* #define SYSTEM_USE_VIDEO_DECODER */

Did you try setting fakeHd = true.

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

When test in my code, the setting is

#define SYSTEM_USE_VIDEO_DECODER and

/* #define SYSTEM_USE_VIDEO_DECODER */

and fakeHdmode also is ture.

the result is above.

0 Yogesh Marathe over 13 years ago in reply to Shary Li

TI__Expert 7765 points

I believe suggestions mentioned by Badri and Brijesh are sufficient to get rid of tvp code. Please ensure when you make these changes in RDK delete dvr_rdk/lib and dvr_rdk/build and then rebuild. This will ensure a clean build with SYSTEM_USE_VIDEO_DECODER undefined and enableConfigExtVideoDecoder set to FALSE.

If you are not using tvp5158 then which device is decoding the capture signal and feeding it to VIP0? Is configuration of that device correct and is it feeding right data to VIP0? Please ensure this.

0 Brijesh Jadav over 13 years ago in reply to Shary Li

TI__Guru**** 494515 points

Hi,

I think it is failing to create capture driver, so some create time argument is wrong.. Can you dump capture create time arguments?

Regards,

Brijesh Jadav

0 Shary Li over 13 years ago in reply to Yogesh Marathe

Intellectual 925 points

Hi, we use 9388 and send handled 422YUYV to VIP0, it can feed right data to VIP0 which has tested.

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

Hi, i dont know what the capture create time arguments? in FVID2_create( )?

0 Brijesh Jadav over 13 years ago in reply to Shary Li

TI__Guru**** 494515 points

Hi,

Yes, please dump and share the arguments passed in FVID2_Create. Essentially parameters of the structure Vps_CaptCreateParams.

thanks,

Brijesh Jadav

0 Badri Narayanan over 13 years ago

TI__Guru 59700 points

Pls use Vps_printf to get prints on the console.You should modify mcfw/src_bios6/link_m3vpss/capture_drv.c to print the Capture driver createParams

0 Brijesh Jadav over 13 years ago

TI__Guru**** 494515 points

Hi,

use Vps_printf to print the create time parameters, use this in links_m3vpss/capture/captureLink_drv.c file and print the create time parameters.

Regards,

Brijesh Jadav

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

Hi,

I am very sorry there is another problems.

The program can run normally. I want write the capture data to file, (VcapVenc_ipcFramesCreate())but in fact the file is empty.

I print some information before "status = Vcap_getFullVideoFrames(&bufList,0);", but it doesn't print on console.

It seems not receive the signal (OSA_semWait(&thrObj->framesInNotifySem,OSA_TIMEOUT_FOREVER);)

I also print the contents of the register(HDVPSS), the vip is not enable.(0000a10a)

What is the problems?

Thanks

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

where I shoule modify in program? Can you help me?

Thanks very much.

0 Badri Narayanan over 13 years ago in reply to Shary Li

TI__Guru 59700 points

I thought you were getting assert in FVID2_create of captureLink.If so you will not get any frames on A8.Also pls correct the following in your code:

ipcFramesOutVpssToHostPrm.baseCreateParams.noNotifyMode = FALSE;

ipcFramesInHostPrm.baseCreateParams.noNotifyMode = FALSE;

Also what are the values for the follwing.It was not clear from the code you shared:

NUM_CAPTURE_DEVICES

Vcap_NUM_Ch

Vcap_NUM_DevIf you dont face assert but still see frame not being received on A8. Pls invoke Vsys_printDetailedStatistics and Vsys_printBufferStatistics and share the log.

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

Hi, thanks very much .

I set the value with FALSE;

And NUM_CAPTURE_DEVICES =1; Vcap_NUM_Ch = 1; Vcap_NUM_DevIf =1;

I change the code as following,is OK?

  pCaptureInstPrm->vipInstId          = SYSTEM_CAPTURE_INST_VIP0_PORTA+vipInstId;
//  pCaptureInstPrm->videoDecoderId     = SYSTEM_DEVICE_VID_DEC_TVP5158_DRV;
  pCaptureInstPrm->inDataFormat       = SYSTEM_DF_RGB24_888;

(vipInstId = 1)

Fullscreen 8228.log.txt Download

=============
 Run-Time Menu
 =============

 1: Capture Write File

 e: Stop Demo

 Enter Choice: 1
demo run
capture start
 -------------------------------------------------------
 System init!!! !!!
 -------------------------------------------------------
 -------------------------------------------------------
 capture params init !!!
 ---------------------------------------------------------------------- CHANNEL DETAILS-------------
Capture Channels => 1
-------------------------------------------
 0: SYSTEM: System Common Init in progress !!!
 0: SYSTEM: IPC init in progress !!!
 13: SYSTEM: Opening MsgQ Heap [IPC_MSGQ_MSG_HEAP] ...
 14: SYSTEM: Creating MsgQ [HOST_MSGQ] ...
 16: SYSTEM: Creating MsgQ [HOST_ACK_MSGQ] ...
 17: SYSTEM: Opening MsgQ [DSP_MSGQ] ...
 17: SYSTEM: Opening MsgQ [VIDEO-M3_MSGQ] ...
 18: SYSTEM: Opening MsgQ [VPSS-M3_MSGQ] ...
 19: SYSTEM: Notify register to [DSP] line 0, event 15 ... 
 19: SYSTEM: Notify register to [VIDEO-M3] line 0, event 15 ... 
 20: SYSTEM: Notify register to [VPSS-M3] line 0, event 15 ... 
 20: SYSTEM: IPC init DONE !!!
 21: SYSTEM: Creating ListMP [HOST_IPC_OUT_28] in region 0 ...
 23: SYSTEM: Creating ListMP [HOST_IPC_IN_28] in region 0 ...
 24: SYSTEM: ListElem Shared Addr = 0x2b0fd280
 25: SYSTEM: Creating ListMP [HOST_IPC_OUT_29] in region 0 ...
 27: SYSTEM: Creating ListMP [HOST_IPC_IN_29] in region 0 ...
 29: SYSTEM: ListElem Shared Addr = 0x2b119e00
 30: SYSTEM: Creating ListMP [HOST_IPC_OUT_23] in region 0 ...
 32: SYSTEM: Creating ListMP [HOST_IPC_IN_23] in region 0 ...
 33: SYSTEM: ListElem Shared Addr = 0x2b136980
 34: SYSTEM: Creating ListMP [HOST_IPC_OUT_24] in region 0 ...
 36: SYSTEM: Creating ListMP [HOST_IPC_IN_24] in region 0 ...
 38: SYSTEM: ListElem Shared Addr = 0x2b156380
 39: SYSTEM: Creating ListMP [HOST_IPC_OUT_25] in region 0 ...
 41: SYSTEM: Creating ListMP [HOST_IPC_IN_25] in region 0 ...
 42: SYSTEM: ListElem Shared Addr = 0x2b175d80
 58: SYSTEM: System Common Init Done !!!

 -------------------------------------------------------
 vsys init!!!
 -------------------------------------------------------
 -------------------------------------------------------
 capture init !!!
 -------------------------------------------------------
Enable RAW Frame Write

 
 Enable file write (YES - y / NO - n) : y
 
 File write ENABLED !!!
 
 
 Enter file write path : /opt
 
 Selected file write path [/opt] 
 
 
 Select FRAME File Write CH ID [0 .. 0] : 0
 
 Selected CH ID = 0 
 
start write file !!!!! 
creat thread!! 
 6860: MCFW  : CPU Revision [ES2.0] !!! 
 6860: MCFW  : Detected [(null)] Board !!! 
 6860: MCFW  : Base Board Revision [DVR] !!! 
 6860: MCFW  : Daughter Card Revision [DVR] !!! 
#############################capture Inst vipInstId = 0

 -------------------------------------------------------
 ##################### capLink will create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 
 Opened file [/opt/VID_CH00.yuv] for writing CH0
open the file
 [host] MCFW_IPCFRAMES:VcapVenc_ipcFramesSendRecvFxn:Entered... [m3vpss ]  31968: CAPTURE: Create in progress !!!
 [m3vpss ] $$$$$$$$$$$$$$$$$$$$$$$$$$$$ This is not 5158!!! 
 [m3vpss ] $$$$$$$$$$$$$$$$$$$$$$$$$$$$ This is not 5158, FVID2_SF_PROGRESSIVE, inWidth= 1920
 [m3vpss ] $$$$$$$$$$$$$$$$$$$$$$$$$$$$ This is not 5158, FVID2_DF_RGB24_888,VPS_CAPT_VIDEO_IF_MODE_24BIT 
 [m3vpss ]  31997: CAPTURE: VIP0 PortA capture mode is [24-bit, Non-mux Discrete Sync - ACTVID_VBLK] !!! 
 [m3vpss ] &&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& pInst ID = 0!!!! 
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->videoCaptureMode = 5
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->videoIfMode = 2
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->inDataFormat = 4103
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->periodicCallbackEnable = 0
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->numCh = 1
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->numStream = 1
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->inScanFormat = 1

 -------------------------------------------------------
 capLink create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 
 [m3vpss ]  UTILS: DMA: Allocated CH (TCC) = 58 (58)
 [m3vpss ] CAPTURE::HEAPID:0    USED:416
 [m3vpss ] CAPTURE::HEAPID:4    USED:53913600
 [m3vpss ]  32223: CAPTURE: Create Done !!!
 [m3vpss ]  32224: NSF: Create in progress !!!

 -------------------------------------------------------
 nsfLink create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 

 -------------------------------------------------------
 ipcFrameOutVpssToHost Link create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 

 [host] IpcFramesInLink_tskMain:Entered
 [host]  7205: IPC_FRAMES_IN   : Create in progress !!!

 [host]  7205: SYSTEM: Opening ListMP [VPSS-M3_IPC_OUT_24] ...
 7207: SYSTEM: Opening ListMP [VPSS-M3_IPC_IN_24] ...

 [host]  7210: IPC_FRAMES_IN   : Create Done !!!

 -------------------------------------------------------
 ipcFrameInHost Link create!!!
 [m3vpss ] NSF::HEAPID:0        USED:128
 [m3vpss ] NSF::HEAPID:1        USED:4928
 [m3vpss ] NSF::HEAPID:4        USED:18800640
 [m3vpss ]  32310: NSF: Create Done !!!
 [m3vpss ]  32310: IPC_FRAMES_OUT   : Create in progress !!!
 [m3vpss ]  32312: IPC_FRAMES_OUT   : Create Done !!!
 [m3vpss ]  32319: CAPTURE: Start in progress !!!
 [m3vpss ]  32319: CAPTURE: Start Done !!!
 -------------------------------------------------------
 -------------------------------------------------------
 capture start !!!
 [m3vpss ]  
 [m3vpss ]  *** Capture Driver Advanced Statistics *** 
 [m3vpss ]  
 [m3vpss ]  VIP Parser Reset Count : 0
 [m3vpss ]  
 [m3vpss ]      |   Total    Even     Odd  Total  Even   Odd  Min /  Max  Min /  Max Dropped Fid Repeat Frame Error Y/C
 [m3vpss ]  CH  |  Fields  Fields  Fields    FPS   FPS   FPS       Width      Height  Fields      Count (Desc Error Y/C)
 [m3vpss ]  ------------------------------------------------------------------------------------------------------------
 [m3vpss ]  
 [m3vpss ]  VIP Capture Port 0 | DescMissMatch1 = 0, DescMissMatch2 = 0 , DescMissMatch3 = 0 
 [m3vpss ]  
 [m3vpss ]  *** Capture List Manager Advanced Statistics *** 
 [m3vpss ]  
 [m3vpss ]  List Post Count        : 1 
 [m3vpss ]  List Stall Count       : 0 
 [m3vpss ]  List Post Time (ms)    : Max = 0, Min = 0, Avg = 0, Total = 0 
 [m3vpss ]  INTC Timeout Count     : (0, 0) (Min timeout value = 993, 1000) 
 [m3vpss ]  Descriptor miss found count : 0 
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  VIP and VPDMA registers, 
 [m3vpss ]  VIP0 : FIQ_STATUS  : 0x4810551c = 0x00000000
 [m3vpss ]  VIP1 : FIQ_STATUS  : 0x48105a1c = 0x00000000
 [m3vpss ]  VPDMA: LIST_BUSY   : 0x4810d00c = 0x00000000
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  32429: CAPTURE: Fields = 0 (fps = 0, CPU Load = 0)
 [m3vpss ]  32429: CAPTURE: Num Resets = 0 (Avg 0 ms per reset)
 [m3vpss ]  32429: SYSTEM  : FREE SPACE : System Heap      = 7104 B, Mbx = 10239 msgs) 
 [m3vpss ]  32429: SYSTEM  : FREE SPACE : SR0 Heap         = 12076032 B (11 MB) 
 [m3vpss ]  32429: SYSTEM  : FREE SPACE : Frame Buffer     = 167293824 B (159 MB) 
 [m3vpss ]  32429: SYSTEM  : FREE SPACE : Bitstream Buffer = 219676544 B (209 MB) 
 [m3vpss ]  32430: SYSTEM  : FREE SPACE : Tiler Buffer     = 256 B (0 MB)  - TILER OFF 
 [m3vpss ]  
 [m3vpss ]  *** [NSF0] NSF Statistics *** 
 [m3vpss ]  
 [m3vpss ]  Elasped Time           : 0 secs
 [m3vpss ]  Total Fields Processed : 0 
 [m3vpss ]  Total Fields FPS       : 0 FPS
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  CH  | In Recv In Reject In Process Out User Out 
 [m3vpss ]  Num | FPS     FPS       FPS        FPS Skip FPS 
 [m3vpss ]  ------------------------------------------------
 [m3vpss ]    0 |       0         0          0   0        0
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  40432: LOAD: CPU: 2.3% HWI: 0.1%, SWI:0.5% 
 [m3vpss ]  
 [m3vpss ]  40432: LOAD: TSK: NSF0                : 1.0% 
 [m3vpss ]  40432: LOAD: TSK: MISC                : 0.7% 
 [m3vpss ]  
 [m3video]  
 [m3video]  40933: LOAD: CPU: 0.4% HWI: 0.1%, SWI:0.1% 
 [m3video]  
 [m3video]  40933: LOAD: TSK: MISC                : 0.2% 
 [m3video]  
 [m3vpss ]  
 [m3vpss ]  *** CAPTURE Statistics *** 
 [m3vpss ] 41934: CAPTURE: Queued to driver = 12, Dequeued from driver = 0
 [m3vpss ] CAPTURE [0] Buf Q Status
 [m3vpss ] Empty Q -> count 0, wrPtr 0, rdPtr 0
 [m3vpss ] Full Q -> count 0, wrPtr 0, rdPtr 0
 [m3vpss ]  
 [m3vpss ]  *** [NSF0] NSF Statistics *** 
 [m3vpss ] 41934: NSF: Rcvd from prev = 0, Returned to prev = 0
 [m3vpss ] NSF Out [0] Buf Q Status
 [m3vpss ] Empty Q -> count 0, wrPtr 0, rdPtr 0
 [m3vpss ] Full Q -> count 0, wrPtr 0, rdPtr 0
 -------------------------------------------------------
 -------------------------------------------------------
 VcapVenc_resetStatistics !!!
 -------------------------------------------------------capture has started

0 Badri Narayanan over 13 years ago in reply to Shary Li

TI__Guru 59700 points

The capture driver statistics indicate no frames are received at VIP.Have you independently validated that Video Decoder configuration has happened correctly ?

Is there any change in behaviour if you set gVcapModuleContext.vcapConfig.enableConfigExtVideoDecoder = TRUE ?

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

Hi,

I change to TRUE, there seems no change.

One colleague tested that the capture data could be sent to vip0, but it is YUV422 ,16bits,

the mode is DEVICE_CAPT_VIDEO_CAPTURE_MODE_SINGLE_CH_NON_MUX_DISCRETE_SYNC_HSYNC_VSYNC.

But the board doesn't support the mode. So I change : pCaptureInstPrm->inDataFormat = SYSTEM_DF_RGB24_888;

Fullscreen 1832.log1.txt Download

root@dvr:/opt/dvr_rdk/ti816x# cd bin/
root@dvr:/opt/dvr_rdk/ti816x/bin# ./dvr_rdk_demo_mcfw_api.out 

 =============
 Run-Time Menu
 =============

 1: Capture Write File

 e: Stop Demo

 Enter Choice: 1
demo run
capture start
 -------------------------------------------------------
 System init!!! !!!
 -------------------------------------------------------
 -------------------------------------------------------
 capture params init !!!
 ---------------------------------------------------------------------- CHANNEL DETAILS-------------
Capture Channels => 1
-------------------------------------------
 0: SYSTEM: System Common Init in progress !!!
 0: SYSTEM: IPC init in progress !!!
 12: SYSTEM: Opening MsgQ Heap [IPC_MSGQ_MSG_HEAP] ...
 13: SYSTEM: Creating MsgQ [HOST_MSGQ] ...
 15: SYSTEM: Creating MsgQ [HOST_ACK_MSGQ] ...
 16: SYSTEM: Opening MsgQ [DSP_MSGQ] ...
 16: SYSTEM: Opening MsgQ [VIDEO-M3_MSGQ] ...
 17: SYSTEM: Opening MsgQ [VPSS-M3_MSGQ] ...
 18: SYSTEM: Notify register to [DSP] line 0, event 15 ... 
 18: SYSTEM: Notify register to [VIDEO-M3] line 0, event 15 ... 
 18: SYSTEM: Notify register to [VPSS-M3] line 0, event 15 ... 
 19: SYSTEM: IPC init DONE !!!
 20: SYSTEM: Creating ListMP [HOST_IPC_OUT_28] in region 0 ...
 22: SYSTEM: Creating ListMP [HOST_IPC_IN_28] in region 0 ...
 23: SYSTEM: ListElem Shared Addr = 0x2b1ab280
 24: SYSTEM: Creating ListMP [HOST_IPC_OUT_29] in region 0 ...
 26: SYSTEM: Creating ListMP [HOST_IPC_IN_29] in region 0 ...
 27: SYSTEM: ListElem Shared Addr = 0x2b1c7e00
 29: SYSTEM: Creating ListMP [HOST_IPC_OUT_23] in region 0 ...
 31: SYSTEM: Creating ListMP [HOST_IPC_IN_23] in region 0 ...
 32: SYSTEM: ListElem Shared Addr = 0x2b1e4980
 33: SYSTEM: Creating ListMP [HOST_IPC_OUT_24] in region 0 ...
 35: SYSTEM: Creating ListMP [HOST_IPC_IN_24] in region 0 ...
 36: SYSTEM: ListElem Shared Addr = 0x2b204380
 37: SYSTEM: Creating ListMP [HOST_IPC_OUT_25] in region 0 ...
 39: SYSTEM: Creating ListMP [HOST_IPC_IN_25] in region 0 ...
 41: SYSTEM: ListElem Shared Addr = 0x2b223d80
 57: SYSTEM: System Common Init Done !!!

 -------------------------------------------------------
 vsys init!!!
 -------------------------------------------------------
 -------------------------------------------------------
 capture init !!!
 -------------------------------------------------------
Enable RAW Frame Write

 
 Enable file write (YES - y / NO - n) : y
 
 File write ENABLED !!!
 
 
 Enter file write path : /opt
 
 Selected file write path [/opt] 
 
 
 Select FRAME File Write CH ID [0 .. 0] : 0
 
 Selected CH ID = 0 
 
start write file !!!!! 
creat thread!! 
 7870: MCFW  : CPU Revision [ES2.0] !!! 
 7870: MCFW  : Detected [(null)] Board !!! 
 7870: MCFW  : Base Board Revision [DVR] !!! 
 7870: MCFW  : Daughter Card Revision [DVR] !!! 
#############################capture Inst vipInstId = 0
############################### copy parameters to allocate driver handle
$$$$$$$$$$$$$$$$$$$$$$$$$$ The handle is not null
 VCAP: TVP5158-0 (0x5c): Device not found !!!

 Audio Channels are not supported
$$$$$$$$$$$$$$$$$$$$$$$$$$ The handle is not null
$$$$$$$$$$$$$$$$$$$$$$$$$$ The handle is not null

 -------------------------------------------------------
 ##################### capLink will create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 
 Opened file [/opt/VID_CH00.yuv] for writing CH0
open the file
 [host] MCFW_IPCFRAMES:VcapVenc_ipcFramesSendRecvFxn:Entered... [m3vpss ]  26506: CAPTURE: Create in progress !!!
 [m3vpss ] $$$$$$$$$$$$$$$$$$$$$$$$$$$$ This is not 5158!!! 
 [m3vpss ] $$$$$$$$$$$$$$$$$$$$$$$$$$$$ This is not 5158, FVID2_SF_PROGRESSIVE, inWidth= 1920
 [m3vpss ] $$$$$$$$$$$$$$$$$$$$$$$$$$$$ This is not 5158, FVID2_DF_RGB24_888,VPS_CAPT_VIDEO_IF_MODE_24BIT 
 [m3vpss ]  26536: CAPTURE: VIP0 PortA capture mode is [24-bit, Non-mux Discrete Sync - ACTVID_VBLK] !!! 
 [m3vpss ] &&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& pInst ID = 0!!!! 
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->videoCaptureMode = 5
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->videoIfMode = 2
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->inDataFormat = 4103
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->periodicCallbackEnable = 1
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->numCh = 1
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->numStream = 1
 [m3vpss ] %%%%%%%%%%%%%%%%%%%%%% pVipCreateArgs->inScanFormat = 1

 -------------------------------------------------------
 capLink create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 
 [m3vpss ]  UTILS: DMA: Allocated CH (TCC) = 58 (58)
 [m3vpss ] CAPTURE::HEAPID:0    USED:416
 [m3vpss ] CAPTURE::HEAPID:4    USED:53913600
 [m3vpss ]  26762: CAPTURE: Create Done !!!
 [m3vpss ]  26763: NSF: Create in progress !!!

 -------------------------------------------------------
 nsfLink create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 

 -------------------------------------------------------
 ipcFrameOutVpssToHost Link create!!!
 -------------------------------------------------------%%%%%%%%%%%%%%%%%%% Start create Link!!! 

 [host] IpcFramesInLink_tskMain:Entered
 [host]  8216: IPC_FRAMES_IN   : Create in progress !!!

 [host]  8216: SYSTEM: Opening ListMP [VPSS-M3_IPC_OUT_24] ...
 8218: SYSTEM: Opening ListMP [VPSS-M3_IPC_IN_24] ...

 [host]  8221: IPC_FRAMES_IN   : Create Done !!!

 -------------------------------------------------------
 ipcFrameInHost Link create!!!
 -------------------------------------------------------$$$$$$$$$$$$$$$$$$$$$$$$$$ The handle is not null
 [m3vpss ] NSF::HEAPID:0        USED:128
 [m3vpss ] NSF::HEAPID:1        USED:4928
 [m3vpss ] NSF::HEAPID:4        USED:18800640
 [m3vpss ]  26848: NSF: Create Done !!!
 [m3vpss ]  26849: IPC_FRAMES_OUT   : Create in progress !!!
 [m3vpss ]  26851: IPC_FRAMES_OUT   : Create Done !!!
 [m3vpss ]  26858: CAPTURE: Start in progress !!!
 [m3vpss ]  26858: CAPTURE: Start Done !!!

 -------------------------------------------------------
 capture start !!!
 [m3vpss ]  
 [m3vpss ]  *** Capture Driver Advanced Statistics *** 
 [m3vpss ]  
 [m3vpss ]  VIP Parser Reset Count : 0
 [m3vpss ]  
 [m3vpss ]      |   Total    Even     Odd  Total  Even   Odd  Min /  Max  Min /  Max Dropped Fid Repeat Frame Error Y/C
 [m3vpss ]  CH  |  Fields  Fields  Fields    FPS   FPS   FPS       Width      Height  Fields      Count (Desc Error Y/C)
 [m3vpss ]  ------------------------------------------------------------------------------------------------------------
 [m3vpss ]  
 [m3vpss ]  VIP Capture Port 0 | DescMissMatch1 = 0, DescMissMatch2 = 0 , DescMissMatch3 = 0 
 [m3vpss ]  
 [m3vpss ]  *** Capture List Manager Advanced Statistics *** 
 [m3vpss ]  
 [m3vpss ]  List Post Count        : 1 
 [m3vpss ]  List Stall Count       : 0 
 [m3vpss ]  List Post Time (ms)    : Max = 0, Min = 0, Avg = 0, Total = 0 
 [m3vpss ]  INTC Timeout Count     : (0, 0) (Min timeout value = 993, 1000) 
 [m3vpss ]  Descriptor miss found count : 0 
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  VIP and VPDMA registers, 
 [m3vpss ]  VIP0 : FIQ_STATUS  : 0x4810551c = 0x00000000
 [m3vpss ]  VIP1 : FIQ_STATUS  : 0x48105a1c = 0x00000000
 [m3vpss ]  VPDMA: LIST_BUSY   : 0x4810d00c = 0x00000000
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  26967: CAPTURE: Fields = 0 (fps = 0, CPU Load = 0)
 [m3vpss ]  26968: CAPTURE: Num Resets = 0 (Avg 0 ms per reset)
 [m3vpss ]  26968: SYSTEM  : FREE SPACE : System Heap      = 7104 B, Mbx = 10239 msgs) 
 [m3vpss ]  26968: SYSTEM  : FREE SPACE : SR0 Heap         = 12076032 B (11 MB) 
 [m3vpss ]  26968: SYSTEM  : FREE SPACE : Frame Buffer     = 167293824 B (159 MB) 
 [m3vpss ]  26968: SYSTEM  : FREE SPACE : Bitstream Buffer = 219676544 B (209 MB) 
 [m3vpss ]  26968: SYSTEM  : FREE SPACE : Tiler Buffer     = 256 B (0 MB)  - TILER OFF 
 [m3vpss ]  
 [m3vpss ]  *** [NSF0] NSF Statistics *** 
 [m3vpss ]  
 [m3vpss ]  Elasped Time           : 0 secs
 [m3vpss ]  Total Fields Processed : 0 
 [m3vpss ]  Total Fields FPS       : 0 FPS
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  CH  | In Recv In Reject In Process Out User Out 
 [m3vpss ]  Num | FPS     FPS       FPS        FPS Skip FPS 
 [m3vpss ]  ------------------------------------------------
 [m3vpss ]    0 |       0         0          0   0        0
 [m3vpss ]  
 [m3vpss ]  
 [m3vpss ]  34971: LOAD: CPU: 5.5% HWI: 0.1%, SWI:0.5% 
 [m3vpss ]  
 [m3vpss ]  34971: LOAD: TSK: CAPTURE             : 3.1% 
 [m3vpss ]  34971: LOAD: TSK: NSF0                : 1.0% 
 [m3vpss ]  34971: LOAD: TSK: MISC                : 0.8% 
 [m3vpss ]  
 [m3video]  
 [m3video]  35472: LOAD: CPU: 0.4% HWI: 0.1%, SWI:0.1% 
 [m3video]  
 [m3video]  35472: LOAD: TSK: MISC                : 0.2% 
 [m3video]  
 [m3vpss ]  
 [m3vpss ]  *** CAPTURE Statistics *** 
 [m3vpss ] 36473: CAPTURE: Queued to driver = 12, Dequeued from driver = 0
 [m3vpss ] CAPTURE [0] Buf Q Status
 [m3vpss ] Empty Q -> count 0, wrPtr 0, rdPtr 0
 [m3vpss ] Full Q -> count 0, wrPtr 0, rdPtr 0
 [m3vpss ]  
 [m3vpss ]  *** [NSF0] NSF Statistics *** 
 [m3vpss ] 36473: NSF: Rcvd from prev = 0, Returned to prev = 0
 [m3vpss ] NSF Out [0] Buf Q Status
 [m3vpss ] Empty Q -> count 0, wrPtr 0, rdPtr 0
 [m3vpss ] Full Q -> count 0, wrPtr 0, rdPtr 0
 -------------------------------------------------------
 -------------------------------------------------------
 VcapVenc_resetStatistics !!!
 -------------------------------------------------------capture has started

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

Hi, if gVcapModuleContext.vcapConfig.enableConfigExtVideoDecoder = TRUE , there printed some other information:

VCAP: TVP5158-0 (0x5c): Device not found !!!

Audio Channels are not supported

0 Badri Narayanan over 13 years ago in reply to Shary Li

TI__Guru 59700 points

How are you configuring your external video decoder in your app ?

Below is what several customers have done to integrate their own video decoders successfully in dvr rdk:

1. Define their own device type for the external video decoder.

2. IMplement the APIs to configure the external video decoder .(Use TVP5158 for reference)

3. In the usecase file set correct parameters for external video decoder and create it

- Set the corresponding parameters for CaptureLink create parameters realted to VIP configuration and then create captureLink.

Have you completed all of the above? From the error it looks like you are setting the device type as TVP 5158 which is wrong. PLs provide the external video decoder data sheet, the code related to video decoder configuration, any changes done to mcfw to integrate the external video decoder and the usecase file with latest captureLink and external video decoder configuration .Without these it is difficult to debug the issue remotely.

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

Hi, I don't want use TVP5158, so I set gVcapModuleContext.vcapConfig.enableConfigExtVideoDecoder = FALSE.

you suggest set to TRUE, and see if there is any change in behavior. So I test, the error is

VCAP: TVP5158-0 (0x5c): Device not found !!!.

But I don't need to use video decoder in 8168, I can't get rid of all setting of video decoder?

Now I get rid of pCaptureInstPrm->videoDecoderId = SYSTEM_DEVICE_VID_DEC_TVP5158_DRV;

and set gVcapModuleContext.vcapConfig.enableConfigExtVideoDecoder = FALSE.

The result is VIP0 A is enable,but

[m3vpss ] *** CAPTURE Statistics ***
[m3vpss ] 36473: CAPTURE: Queued to driver = 12, Dequeued from driver = 0
[m3vpss ] CAPTURE [0] Buf Q Status
[m3vpss ] Empty Q -> count 0, wrPtr 0, rdPtr 0
[m3vpss ] Full Q -> count 0, wrPtr 0, rdPtr 0

So what's wrong?

0 Badri Narayanan over 13 years ago in reply to Shary Li

TI__Guru 59700 points

How is your camera interfaced to 8168 VIP port. What is the format the video signals are sent to 8168 ? I understand you dont require TVP but only now I understand you dont have any video decoder IC at all. If you dont want any video decoder configuration then set

gVcapModuleContext.vcapConfig.enableConfigExtVideoDecoder = FALSE

undefine

//#define SYSTEM_USE_VIDEO_DECODER

The remaining part is VIP configuration.Pls provide details on what format video data is sent to VIP port and we can provide details on VIP configuration.

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

I find just only in system_debug.h, there define SYSTEM_USE_VIDEO_DECODER as following:

#if defined(TI8107_DVR)
#define SYSTEM_USE_VIDEO_DECODER
#endif

Is there another define?

In my board, the cameral will capture data and send to 9388, and the send to VIP0 A. The video format is YUV422 16-bit discrete sync mode, but 8168 not support the format.

so I change pCaptureInstPrm->inDataFormat = SYSTEM_DF_RGB24_888;

the format is not right, but there should be still data, is right?

0 Badri Narayanan over 13 years ago in reply to Shary Li

TI__Guru 59700 points

#if defined(TI8107_DVR)
#define SYSTEM_USE_VIDEO_DECODER
#endif

The above is the only place where this is defined so your setting is correct.

What does 9388 mean. Are you refering to http://www.analog.com/static/imported-files/data_sheets/AD9388A.pdf ?

0 Shary Li over 13 years ago in reply to Badri Narayanan

Intellectual 925 points

Yes, it's AD9388, another colleague works on it. He uses it in another project, it can successfully send data (16 bits discrete sync mode) .

0 Sujith over 13 years ago in reply to Shary Li

TI__Genius 12455 points

Hi,

Could you please check if on the following, assuming that you would be using 16 embedded sync mode of capture.

Ensure link supports 16 bit mode of capture.

In file \dvr_rdk\mcfw\src_bios6\links_m3vpss\capture\captureLink_drv.c
In function CaptureLink_drvCreateInst () ensure

videoCaptureMode = VPS_CAPT_VIDEO_CAPTURE_MODE_SINGLE_CH_NON_MUX_EMBEDDED_SYNC;
videoIfMode = VPS_CAPT_VIDEO_IF_MODE_16BIT;

Check the pin mux for VIP data, ensure that all 16 data lines of VIP1 is selected for VIP.
Please dump the content of memory

After the above listed steps, please dump the contents of memory location 0x48105A00 to 0x48105A10 and share it with us.
We want to check if the VIP had detected the signal.

In case you are using 16 bit discrete sync mode of capture, please check on the following.

Ensure link supports 16 bit mode of capture.

In file \dvr_rdk\mcfw\src_bios6\links_m3vpss\capture\captureLink_drv.c
In function CaptureLink_drvCreateInst () ensure

videoCaptureMode = VPS_CAPT_VIDEO_CAPTURE_MODE_SINGLE_CH_NON_MUX_DISCRETE_SYNC_ACTVID_VBLK;
Please share the wave form for vSync, hSync DE (Data enable / active video) with respect to pixel clock, based on the wave form we could recommend the mode of discrete sync to be used.
videoIfMode = VPS_CAPT_VIDEO_IF_MODE_16BIT;

Check the pin mux for VIP data, ensure that all 16 data lines, vSync, hSync & DE pins of VIP1 is selected for VIP.
Please dump the content of memory

After the above listed steps, please dump the contents of memory location 0x48105A00 to 0x48105A10 and share it with us.
We want to check if the VIP had detected the signal.

Thanks,

Sujith

0 Shary Li over 13 years ago in reply to Sujith

Intellectual 925 points

Hi, thanks very much for your reply.

I use 16 embedded sync mode of capture. I print some information in \dvr_rdk\mcfw\src_bios6\links_m3vpss\capture\captureLink_drv.c.

And videoCaptureMode = VPS_CAPT_VIDEO_CAPTURE_MODE_SINGLE_CH_NON_MUX_EMBEDDED_SYNC;

videoIfMode = VPS_CAPT_VIDEO_IF_MODE_16BIT;

But the contents of memory location 0x48105A00 to 0x48105A10 is all zero.

I use VIP0 A.But I found 0x48105A00 is for VIP1.

RDK can only support FVID2_DF_YUV422P,FVID2_DF_YUV444P, FVID2_DF_RGB24_888. I want use 16bit, but it can not support 422I_YUYV, so I use YUV422P, is it OK?

0 Sujith over 13 years ago in reply to Shary Li

TI__Genius 12455 points

Hi,

Yes, 0x48105A00 is for VIP 1, could you please dump VIP 0 registers and share it with us?

We will first check if VIP is able to detect the video signals, post that we can check on the data types and others.

Thanks,

Sujith

0 Shary Li over 13 years ago in reply to Sujith

Intellectual 925 points

48105500: 00000001 0000a110 00000000 00000000 ................
48105510: 00000000 00000000 00000000 00030000

0 Brijesh Jadav over 13 years ago in reply to Shary Li

TI__Guru**** 494515 points

Hi,

It looks like there is some issue in your SAV/EAV codes, because VIP says there is a protocol violation.. Could you please check if the SAV/EAV codes inserted are correct and they are inserted in both the channels i.e. luma and chroma..

If this does not work out, is it possible to connect sync signal and configure VIP to work in discrete sync mode..

Thanks,

Brijesh Jadav

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

Hi,

Now I don't need to use 5158. And I want capture 1080P 60, 16bits-422, and SINGLE_CH_NON_MUX_EMBEDDED_SYNC.

I need to change the driver of capture?

0 Brijesh Jadav over 13 years ago in reply to Shary Li

TI__Guru**** 494515 points

No, there is no need to change the driver, driver has been tested with 16 bit embedded sync format with input from TVP7002.

Regards,

Brijesh Jadav

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

Hi, thanks very much for your reply.

Now I din't change the driver, and just configure the capture params.

But it doesn't capture any frame. How should I change the code?

I am very confused. My colleague has test the signal is in VIP0 pins.

0 Brijesh Jadav over 13 years ago in reply to Shary Li

TI__Guru**** 494515 points

Hi Shary,

Could you first check your input is correct? it is sending correct SAV/EAV codes? it is sending SAV/EAV codes on both the channels? H and V bits are toggling correctly in SAV/EAV codes? Once all of these are correct, VIP will receive frames correctly and you will be able to capture frame correctly..

Regards,

Brijesh Jadav

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

Hi, thanks very much for your help.

I want to know, whether if the input is correct, I just need to delete all codes of 5158, and configure the VIP.

Are those is enough? And another thing I should do?

I want to ensure this. Somebody asked me to change the driver, I want to know whether it is necessary.

Can you help me?

0 Shary Li over 13 years ago in reply to Brijesh Jadav

Intellectual 925 points

Hi,

I presumptuously ask Can you share the test code using TVP7002?

Processors

Processors forum

DVR_RDK2.8 Capture