Our customer purchased a new TMDX654IDKEVM, but it can fail to boot after power up.
If the SD card with the diagnostic applications is used, nothing is printed on the terminal after power up. After being reset by PORz switch, it can boot and all tests in the Power On Self Test pass.
DIAGNOSTIC TEST FRAMEWORK
Version - 01.00.00.02
Build Date - Oct 17 2019, Time - 03:53:34
Command options:
help - displays this help menu again
run - run a diagnostic application
status - prints the test status
Running Power On Self Tests...
Press 'b' to Skip the Test
1
Parsing bootEepromCompliance_TEST
Running bootEepromCompliance_TEST
*********************************************
* Boot EEPROM Test *
*********************************************
Running Boot EEPROM test
Detecting the Boot EEPROM device...
Boot EEPROM device detection successful
Boot EEPROM boundary verification test...
Verifying the Boot EEPROM first page...
Verifying the Boot EEPROM last page...
Boot EEPROM boundary verification test successful
Boot EEPROM test Passed
Finished running bootEepromCompliance_TEST, result passed!
Parsing memCompliance_TEST
Running memCompliance_TEST
*********************************************
* DDR Memory Test *
*********************************************
Testing writing and reading memory
board_external_memory_test: Start address (0x80000000), end address (0xffffffff)
Address Bus Test Started
Writing to test area...
Writing Memory 0x80000000
Writing Memory 0x80000004
Writing Memory 0x80000008
Writing Memory 0x80000010
Writing Memory 0x80000020
Writing Memory 0x80000040
Writing Memory 0x80000080
Writing Memory 0x80000100
Writing Memory 0x80000200
Writing Memory 0x80000400
Writing Memory 0x80000800
Writing Memory 0x80001000
Writing Memory 0x80002000
Writing Memory 0x80004000
Writing Memory 0x80008000
Writing Memory 0x80010000
Writing Memory 0x80020000
Writing Memory 0x80040000
Writing Memory 0x80080000
Writing Memory 0x80100000
Writing Memory 0x80200000
Writing Memory 0x80400000
Writing Memory 0x80800000
Writing Memory 0x81000000
Writing Memory 0x82000000
Writing Memory 0x84000000
Writing Memory 0x88000000
Writing Memory 0x90000000
Writing Memory 0xa0000000
Writing Memory 0xc0000000
Write finished!
Checking values...
Reading Memory 0x80000000
Reading Memory 0x80000004
Reading Memory 0x80000008
Reading Memory 0x80000010
Reading Memory 0x80000020
Reading Memory 0x80000040
Reading Memory 0x80000080
Reading Memory 0x80000100
Reading Memory 0x80000200
Reading Memory 0x80000400
Reading Memory 0x80000800
Reading Memory 0x80001000
Reading Memory 0x80002000
Reading Memory 0x80004000
Reading Memory 0x80008000
Reading Memory 0x80010000
Reading Memory 0x80020000
Reading Memory 0x80040000
Reading Memory 0x80080000
Reading Memory 0x80100000
Reading Memory 0x80200000
Reading Memory 0x80400000
Reading Memory 0x80800000
Reading Memory 0x81000000
Reading Memory 0x82000000
Reading Memory 0x84000000
Reading Memory 0x88000000
Reading Memory 0x90000000
Reading Memory 0xa0000000
Reading Memory 0xc0000000
Board memory test passed!
Memory test passed!
Finished running memCompliance_TEST, result passed!
Parsing emmcCompliance_TEST
Running emmcCompliance_TEST
*********************************************
* eMMC Test *
*********************************************
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode8 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode4 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode2 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode1 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Finished running emmcCompliance_TEST, result passed!
Parsing norflashCompliance_TEST
Running norflashCompliance_TEST
***************************************
* SPI FlASH Test *
***************************************
Reading Flash Device ID...
Device ID 0 - 0x20
Device ID 1 - 0xba
Device ID 2 - 0x18
Flash Device ID Match!
Flash Device ID Read Passed!
Verifying Sector - 0
Data Read matches with Data written
SPI Flash Test Passed!
SPI NOR Flash Test Passed
Finished running norflashCompliance_TEST, result passed!
Parsing ospiCompliance_TEST
Running ospiCompliance_TEST
*********************************************
* OSPI FLASH Test *
*********************************************
OSPI NOR device ID: 0x5b1a, manufacturer ID: 0x2c
Verifying the OSPI Flash first page...
OSPI NOR Flash first page verification Successful
OSPI NOR Flash verification Successful
OSPI Flash Test Passed!
Finished running ospiCompliance_TEST, result passed!
Parsing ledCompliance_TEST
Running ledCompliance_TEST
*********************************************
* LED Test *
*********************************************
Testing LED
Blinking LEDs...
Received: y
Test PASSED!
LED Test Passed
Finished running ledCompliance_TEST, result passed!
Parsing bootSwitchCompliance_TEST
Running bootSwitchCompliance_TEST
*********************************************
* Boot Switch Test *
*********************************************
Boot Switch SW3 Value - OFF ON ON OFF OFF OFF OFF OFF OFF OFF
Boot Switch SW2 Value - OFF OFF ON OFF OFF OFF OFF OFF OFF
Boot Switch SW4 Value - ON ON
Test Passed
Finished running bootSwitchCompliance_TEST, result passed!
Parsing eepromCompliance_TEST
Running eepromCompliance_TEST
*********************************************
* EEPROM Test *
*********************************************
CP Board:
Displaying Header Fields
========================
Header ID: 0xee3355aa
Displaying Board Info Fields
============================
Board Name: AM6-COMPROCEVM
Design Revision: E3
PROC Number: 0062
Variant: 01
PCB Revision: E3
Schematic and BOM Revision: E3
Software Revision: 01
Vendor ID: 01
Build Week: 40
Build Year: 19
Board ID: 4P0081
Serial Number: 0140
Displaying DDR Fields
=====================
DDR Control Word: 5850
Displaying MAC Info Fields
==========================
MAC Control Word: 08
MAC ADDR0: 70-ff-76-1d-5c-52
MAC ADDR1: 70-ff-76-1d-5c-53
Application Card:
Displaying Header Fields
========================
Header ID: 0xee3355aa
Displaying Board Info Fields
============================
Board Name: AM6-IDKAPPEVM
Design Revision: E4
PROC Number: 0064
Variant: 01
PCB Revision: E4
Schematic and BOM Revision: E4
Software Revision: 01
Vendor ID: 01
Build Week: 38
Build Year: 19
Board ID: 4P0082
Serial Number: 0076
Displaying MAC Info Fields
==========================
MAC Control Word: 18
MAC ADDR0: 70-ff-76-1d-5e-5e
MAC ADDR1: 70-ff-76-1d-5e-5f
MAC ADDR2: 70-ff-76-1d-5e-60
MAC ADDR3: 70-ff-76-1d-5e-61
SERDES Personality Card:
Displaying Header Fields
========================
Header ID: 0xee3355aa
Displaying Board Info Fields
============================
Board Name: SER-PCIE2LEVM
Design Revision: E3
PROC Number: 0067
Variant: 01
PCB Revision: E3
Schematic and BOM Revision: E3
Software Revision: 01
Vendor ID: 01
Build Week: 39
Build Year: 19
Board ID: 4P0088
Serial Number: 0167
EEPROM Test Passed
Finished running eepromCompliance_TEST, result passed!
Power On Self Test Result
All Tests Passed
[Diag Menu]: run
Diagnostic Test Status:
--------------------------------------------------------------
ID Name Pass # of times Ran
0 Auto Run All Compliance Tests
1 bootEepromStress_TEST No 0
2 bootEeprom_TEST No 0
3 bootSwitch_TEST No 0
4 button_TEST No 0
5 currentMonitorStress_TEST No 0
6 currentMonitor_TEST No 0
7 eeprom_TEST No 0
8 emacStress_TEST No 0
9 emac_TEST No 0
10 emmcStress_TEST No 0
11 emmc_TEST No 0
12 extRtcStress_TEST No 0
13 extRtc_TEST No 0
14 icssgEmacStress_TEST No 0
15 icssgEmac_TEST No 0
16 icssgLedStress_TEST No 0
17 icssgLed_TEST No 0
18 ledIndustrialStress_TEST No 0
19 ledIndustrial_TEST No 0
20 ledStress_TEST No 0
21 led_TEST No 0
22 mcanStress_TEST No 0
23 mcan_TEST No 0
24 memStress_TEST No 0
25 mem_TEST No 0
26 mmcsdStress_TEST No 0
27 mmcsd_TEST No 0
28 norflashStress_TEST No 0
29 norflash_TEST No 0
30 ospiStress_TEST No 0
31 ospi_TEST No 0
32 pcie_TEST No 0
33 rotarySwitch_TEST No 0
34 rs485_TEST No 0
35 temperatureStress_TEST No 0
36 temperature_TEST No 0
37 uart_TEST No 0
38 usbDevice_TEST No 0
39 usbHostStress_TEST No 0
40 usbHost_TEST No 0
Select test number (1 - 40): 0
Diagnostic Test Status:
--------------------------------------------------------------
ID Name Pass # of times Ran
1 bootEepromCompliance_TEST No 0
2 bootSwitchCompliance_TEST No 0
3 buttonCompliance_TEST No 0
4 currentMonitorCompliance_TEST No 0
5 eepromCompliance_TEST No 0
6 emacCompliance_TEST No 0
7 emmcCompliance_TEST No 0
8 extRtcCompliance_TEST No 0
9 icssgEmacCompliance_TEST No 0
10 icssgLedCompliance_TEST No 0
11 ledCompliance_TEST No 0
12 ledIndustrialCompliance_TEST No 0
13 mcanCompliance_TEST No 0
14 memCompliance_TEST No 0
15 mmcsdCompliance_TEST No 0
16 norflashCompliance_TEST No 0
17 ospiCompliance_TEST No 0
18 pcieEPCompliance_TEST No 0
19 pcieRCCompliance_TEST No 0
20 rotarySwitchCompliance_TEST No 0
21 rs485uartCompliance_TEST No 0
22 temperatureCompliance_TEST No 0
23 uartCompliance_TEST No 0
24 usbHostCompliance_TEST No 0
Enter the number of iterations : 0
Running Compliance Test...
Enter 'b' in Serial Console to Terminate the Test
Parsing bootEepromCompliance_TEST
Running bootEepromCompliance_TEST
*********************************************
* Boot EEPROM Test *
*********************************************
Running Boot EEPROM test
Detecting the Boot EEPROM device...
Boot EEPROM device detection successful
Boot EEPROM boundary verification test...
Verifying the Boot EEPROM first page...
Verifying the Boot EEPROM last page...
Boot EEPROM boundary verification test successful
Boot EEPROM test Passed
Finished running bootEepromCompliance_TEST, result passed!
Parsing bootSwitchCompliance_TEST
Running bootSwitchCompliance_TEST
*********************************************
* Boot Switch Test *
*********************************************
Boot Switch SW3 Value - OFF ON ON OFF OFF OFF OFF OFF OFF OFF
Boot Switch SW2 Value - OFF OFF ON OFF OFF OFF OFF OFF OFF
Boot Switch SW4 Value - ON ON
Test Passed
Finished running bootSwitchCompliance_TEST, result passed!
Parsing buttonCompliance_TEST
Running buttonCompliance_TEST
*********************************************
* Button Test *
*********************************************
Running button test...
Button SW 5 Button SW 5 Value - 1
Button SW 6 Button SW 6 Value - 1
Test PASSED!
Finished running buttonCompliance_TEST, result passed!
Parsing currentMonitorCompliance_TEST
Running currentMonitorCompliance_TEST
**********************************************
* Current Monitor Test *
**********************************************
Verifying Device VDD_CORE at Address - 0x40
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 4mV
Reading the Bus Voltage register...
Bus Voltage = 1001mV
Reading the Power register...
Power = 34024mW
Reading the Current register...
Current = 2051mA
Verifying Device VDD_MCU at Address - 0x41
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 4mV
Reading the Bus Voltage register...
Bus Voltage = 1002mV
Reading the Power register...
Power = 21625mW
Reading the Current register...
Current = 431mA
Verifying Device VDD_MPU at Address - 0x42
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 0mV
Reading the Bus Voltage register...
Bus Voltage = 1001mV
Reading the Power register...
Power = 14266mW
Reading the Current register...
Current = 194mA
Verifying Device SoC_DVDD3V3 at Address - 0x43
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 0mV
Reading the Bus Voltage register...
Bus Voltage = 3351mV
Reading the Power register...
Power = 6675mW
Reading the Current register...
Current = 48mA
Verifying Device SoC_DVDD1V8 at Address - 0x44
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 0mV
Reading the Bus Voltage register...
Bus Voltage = 1796mV
Reading the Power register...
Power = 3509mW
Reading the Current register...
Current = 28mA
Verifying Device SoC_AVDD1V8 at Address - 0x45
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 3mV
Reading the Bus Voltage register...
Bus Voltage = 1792mV
Reading the Power register...
Power = 16896mW
Reading the Current register...
Current = 75mA
Verifying Device SoC_VDDS_DDR at Address - 0x46
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 1mV
Reading the Bus Voltage register...
Bus Voltage = 1200mV
Reading the Power register...
Power = 3097mW
Reading the Current register...
Current = 147mA
Verifying Device VDD_DDR at Address - 0x47
Setting the configuration register...
Setting the calibration register...
Reading the Shunt Voltage register...
Shunt Voltage = 1mV
Reading the Bus Voltage register...
Bus Voltage = 1200mV
Reading the Power register...
Power = 8103mW
Reading the Current register...
Current = 119mA
Current Monitor Test Passed
Finished running currentMonitorCompliance_TEST, result passed!
Parsing eepromCompliance_TEST
Running eepromCompliance_TEST
*********************************************
* EEPROM Test *
*********************************************
CP Board:
Displaying Header Fields
========================
Header ID: 0xee3355aa
Displaying Board Info Fields
============================
Board Name: AM6-COMPROCEVM
Design Revision: E3
PROC Number: 0062
Variant: 01
PCB Revision: E3
Schematic and BOM Revision: E3
Software Revision: 01
Vendor ID: 01
Build Week: 40
Build Year: 19
Board ID: 4P0081
Serial Number: 0140
Displaying DDR Fields
=====================
DDR Control Word: 5850
Displaying MAC Info Fields
==========================
MAC Control Word: 08
MAC ADDR0: 70-ff-76-1d-5c-52
MAC ADDR1: 70-ff-76-1d-5c-53
Application Card:
Displaying Header Fields
========================
Header ID: 0xee3355aa
Displaying Board Info Fields
============================
Board Name: AM6-IDKAPPEVM
Design Revision: E4
PROC Number: 0064
Variant: 01
PCB Revision: E4
Schematic and BOM Revision: E4
Software Revision: 01
Vendor ID: 01
Build Week: 38
Build Year: 19
Board ID: 4P0082
Serial Number: 0076
Displaying MAC Info Fields
==========================
MAC Control Word: 18
MAC ADDR0: 70-ff-76-1d-5e-5e
MAC ADDR1: 70-ff-76-1d-5e-5f
MAC ADDR2: 70-ff-76-1d-5e-60
MAC ADDR3: 70-ff-76-1d-5e-61
SERDES Personality Card:
Displaying Header Fields
========================
Header ID: 0xee3355aa
Displaying Board Info Fields
============================
Board Name: SER-PCIE2LEVM
Design Revision: E3
PROC Number: 0067
Variant: 01
PCB Revision: E3
Schematic and BOM Revision: E3
Software Revision: 01
Vendor ID: 01
Build Week: 39
Build Year: 19
Board ID: 4P0088
Serial Number: 0167
EEPROM Test Passed
Finished running eepromCompliance_TEST, result passed!
Parsing emacCompliance_TEST
Running emacCompliance_TEST
************************************************
* ETHERNET LOOPBACK Test *
************************************************
Reading Ethernet PHY Register Dump...
Register Dump for PHY Addr - 0x0000
PHY Register 0x0000 - 0x1140
PHY Register 0x0001 - 0x7949
PHY Register 0x0002 - 0x2000
PHY Register 0x0003 - 0xa231
PHY Register 0x0004 - 0x01e1
PHY Register 0x0005 - 0x0000
PHY Register 0x0006 - 0x0064
PHY Register 0x0007 - 0x2001
PHY Register 0x0008 - 0x0000
PHY Register 0x0009 - 0x0300
PHY Register 0x000a - 0x0000
PHY Register 0x000b - 0x0000
PHY Register 0x000c - 0x0000
PHY Register 0x000d - 0x401f
PHY Register 0x000e - 0x0007
PHY Register 0x000f - 0x3000
PHY Register(STRAP1) 0x006e - 0x0000
Default PHY Register(STRAP2) Data mismatch
PHY Register(STRAP2) 0x006f - 0x0100
RGMII Control Register (RGMIICTL) Value - 0x00d1
--- RGMII_RX_CLK_DELAY - 0x0001
--- RGMII_TX_CLK_DELAY - 0x0000
RGMII Delay Control Register (RGMIIDCTL) Value - 0x0007
Strapping Registers data mismatch
EMAC loopback test application initialization
main: emac_open success
Configuring Phy
Waiting for Link Status
LINK Timeout!
EMAC Test Failed!!
Finished running emacCompliance_TEST, result failed!
Parsing emmcCompliance_TEST
Running emmcCompliance_TEST
*********************************************
* eMMC Test *
*********************************************
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode8 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode4 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode2 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Setting EMMC Support Mode1 configuration...
Getting eMMC parameters
eMMC: BlockCount = 0x1da4000
PASS: Read/Write Success for this block-0x300000
PASS: eMMC Read/Write Success for this pattern
Finished running emmcCompliance_TEST, result passed!
Parsing extRtcCompliance_TEST
Running extRtcCompliance_TEST
*********************************************
* RTC Test *
*********************************************
Running RTC Test...
Setting Time...
Setting Date...
Reading Time...
Reading Date...
Displaying time: 11:59:53 PM
Displaying Day: Sunday
Displaying Date: 31/12/18
RTC test passed...
RTC Test Passed
Finished running extRtcCompliance_TEST, result passed!
Parsing icssgEmacCompliance_TEST
Running icssgEmacCompliance_TEST
Interposer card is NOT present
***************************************
* ICSSG EMAC TEST *
***************************************
Performing UDMA driver init...
Reading Ethernet PHY Register Dump...
Register Dump for PHY Addr - 0x0000
PHY Register 0x0000 - 0x1140
PHY Register 0x0001 - 0x7949
PHY Register 0x0002 - 0x2000
PHY Register 0x0003 - 0xa231
PHY Register 0x0004 - 0x01e1
PHY Register 0x0005 - 0x0000
PHY Register 0x0006 - 0x0064
PHY Register 0x0007 - 0x2001
PHY Register 0x0008 - 0x0000
PHY Register 0x0009 - 0x1b00
PHY Register 0x000a - 0x0000
PHY Register 0x000b - 0x0000
PHY Register 0x000c - 0x0000
PHY Register 0x000d - 0x401f
PHY Register 0x000e - 0x00d9
PHY Register 0x000f - 0x3000
PHY Configuration Register(CFG4) 0x0031 - 0x0302
PHY Register(STRAP1) 0x006e - 0x0000
PHY Register(STRAP2) 0x006f - 0x0500
RGMII Control Register (RGMIICTL) Value - 0x00d9
--- RGMII_RX_CLK_DELAY - 0x0001
--- RGMII_TX_CLK_DELAY - 0x0000
RGMII Delay Control Register (RGMIIDCTL) Value - 0x0007
If the SD card with Linux is used, it can boot, but repeats the reset because it fails to initialize the DDR4 memory. After being reset by PORz switch, it boots without problems.
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
read_dqs_training:ERROR: Read DQS Gate training failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
read_dqs_training:ERROR: Read DQS Gate training failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
read_dqs_training:ERROR: Read DQS Gate training failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
rest_training: ERROR: Write Leveling adjustment failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
rest_training: ERROR: Write Leveling adjustment failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
rest_training: ERROR: Write Leveling adjustment failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
Trying to boot from MMC2
Starting ATF on ARM64 core...
NOTICE: BL31: v2.1(release):ti2019.01-rc2
NOTICE: BL31: Built : 04:28:26, Jul 7 2019
I/TC:
I/TC: OP-TEE version: 3.2.0-583-g251f7c6-dev #1 Sun Jul 7 04:40:43 UTC 2019 aarch64
I/TC: Initialized
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:09:26 +0000)
detected AM6-IDKAPPEVM
detected SER-PCIE2LEVM
Trying to boot from MMC2
U-Boot 2019.01-g8b90adfb16 (Jul 07 2019 - 05:09:26 +0000)
Model: Texas Instruments AM654 Base Board
DRAM: 4 GiB
MMC: sdhci@4f80000: 0, sdhci@04FA0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
detected AM6-IDKAPPEVM
detected SER-PCIE2LEVM
Net: eth2: pruss0_eth
Warning: cpsw_nuss@046000000 using MAC address from ROM
, eth0: cpsw_nuss@046000000, eth1: pruss2_eth
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
SD/MMC found on device 1
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc1 ...
Running uenvcmd ...
1 bytes read in 2 ms (0 Bytes/s)
Already setup.
12632072 bytes read in 1062 ms (11.3 MiB/s)
71809 bytes read in 11 ms (6.2 MiB/s)
11402 bytes read in 3 ms (3.6 MiB/s)
2084 bytes read in 2 ms (1017.6 KiB/s)
## Flattened Device Tree blob at 82000000
Booting using the fdt blob at 0x82000000
Loading Device Tree to 00000000fddb7000, end 00000000fdecbfff ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 4.19.38-g4dae378bbe (oe-user@oe-host) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #1 SMP PREEMPT Sun Jul 7 03:42:51 UTC 2019
[ 0.000000] Machine model: Texas Instruments AM654 Base Board
[ 0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '')
[ 0.000000] bootconsole [ns16550a0] enabled
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009b000000, size 1 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@9b000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009b100000, size 15 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-memory@9b100000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009c000000, size 1 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@9c000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009c100000, size 7 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-memory@9c100000, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 512 MiB at 0x00000000c0000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x3e4 with crng_init=0
[ 0.000000] percpu: Embedded 2 pages/cpu s48536 r8192 d74344 u131072
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64704
[ 0.000000] Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),128k(ospi.env),128k(ospi.env.backup),1m(ospi.sysfw),-@8m(ospi.rootfs) root=PARTUUID=5d2ac6ad-02 rw rootfstype=ext4 rootwait
[ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes)
[ 0.000000] software IO TLB: mapped [mem 0xf9db0000-0xfddb0000] (64MB)
[ 0.000000] Memory: 3529856K/4145152K available (8062K kernel code, 752K rwdata, 2880K rodata, 576K init, 614K bss, 91008K reserved, 524288K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] ITS [mem 0x01820000-0x0182ffff]
[ 0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS
[ 0.000000] ITS@0x0000000001820000: allocated 1048576 Devices @8c0800000 (flat, esz 8, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x00000008c00c0000
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001880000
[ 0.000000] CPU0: using LPI pending table @0x00000008c00d0000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns
[ 0.000005] sched_clock: 56 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns
[ 0.008698] Console: colour dummy device 80x25
[ 0.013293] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=800000)
[ 0.023981] pid_max: default: 32768 minimum: 301
[ 0.028806] Security Framework initialized
[ 0.033067] Mount-cache hash table entries: 8192 (order: 0, 65536 bytes)
[ 0.039948] Mountpoint-cache hash table entries: 8192 (order: 0, 65536 bytes)
[ 0.071385] ASID allocator initialised with 32768 entries
[ 0.084953] rcu: Hierarchical SRCU implementation.
[ 0.098034] Platform MSI: gic-its@18200000 domain created
[ 0.103879] PCI/MSI: /interconnect@100000/interrupt-controller@1800000/gic-its@18200000 domain created
[ 0.121447] smp: Bringing up secondary CPUs ...
[ 0.158571] Detected VIPT I-cache on CPU1
[ 0.158610] GICv3: CPU1: found redistributor 1 region 0:0x00000000018a0000
[ 0.158666] CPU1: using LPI pending table @0x00000008c0330000
[ 0.158713] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.220252] Detected VIPT I-cache on CPU2
[ 0.220294] GICv3: CPU2: found redistributor 100 region 0:0x00000000018c0000
[ 0.220358] CPU2: using LPI pending table @0x00000008c03c0000
[ 0.220406] CPU2: Booted secondary processor 0x0000000100 [0x410fd034]
[ 0.252664] Detected VIPT I-cache on CPU3
[ 0.252694] GICv3: CPU3: found redistributor 101 region 0:0x00000000018e0000
[ 0.252750] CPU3: using LPI pending table @0x00000008c0450000
[ 0.252787] CPU3: Booted secondary processor 0x0000000101 [0x410fd034]
[ 0.252927] smp: Brought up 1 node, 4 CPUs
[ 0.328557] SMP: Total of 4 processors activated.
[ 0.333380] CPU features: detected: GIC system register CPU interface
[ 0.339991] CPU features: detected: 32-bit EL0 Support
[ 0.367819] CPU: All CPU(s) started at EL2
[ 0.372039] alternatives: patching kernel code
[ 0.378055] devtmpfs: initialized
[ 0.393211] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.403215] futex hash table entries: 1024 (order: 0, 65536 bytes)
[ 0.410953] pinctrl core: initialized pinctrl subsystem
[ 0.416947] NET: Registered protocol family 16
[ 0.422731] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
[ 0.430321] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.443710] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.452543] davinci_gpio 42110000.wkup_gpio0: IRQ not populated, err = -517
[ 0.466827] davinci_gpio 600000.main_gpio0: IRQ not populated, err = -517
[ 0.474034] davinci_gpio 601000.main_gpio1: IRQ not populated, err = -517
[ 0.492117] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.498996] HugeTLB registered 512 MiB page size, pre-allocated 0 pages
[ 0.507812] cryptd: max_cpu_qlen set to 1000
[ 0.514003] media: Linux media interface: v0.10
[ 0.518684] videodev: Linux video capture interface: v2.00
[ 0.524342] pps_core: LinuxPPS API ver. 1 registered
[ 0.529425] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.538786] PTP clock support registered
[ 0.542827] EDAC MC: Ver: 3.0.0
[ 0.547350] Advanced Linux Sound Architecture Driver Initialized.
[ 0.554534] clocksource: Switched to clocksource arch_sys_counter
[ 0.560991] VFS: Disk quotas dquot_6.6.0
[ 0.565101] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes)
[ 0.579401] NET: Registered protocol family 2
[ 0.584559] tcp_listen_portaddr_hash hash table entries: 4096 (order: 0, 65536 bytes)
[ 0.592711] TCP established hash table entries: 32768 (order: 2, 262144 bytes)
[ 0.600404] TCP bind hash table entries: 32768 (order: 3, 524288 bytes)
[ 0.607757] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.614624] UDP hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.620889] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.627771] NET: Registered protocol family 1
[ 0.632838] RPC: Registered named UNIX socket transport module.
[ 0.638917] RPC: Registered udp transport module.
[ 0.643735] RPC: Registered tcp transport module.
[ 0.648551] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.656304] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.669630] Initialise system trusted keyrings
[ 0.674404] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[ 0.686270] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.693084] NFS: Registering the id_resolver key type
[ 0.698290] Key type id_resolver registered
[ 0.702575] Key type id_legacy registered
[ 0.706695] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.713722] 9p: Installing v9fs 9p2000 file system support
[ 0.724163] Key type asymmetric registered
[ 0.728376] Asymmetric key parser 'x509' registered
[ 0.733436] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 0.741115] io scheduler noop registered
[ 0.745140] io scheduler deadline registered
[ 0.749669] io scheduler cfq registered (default)
[ 0.754496] io scheduler mq-deadline registered
[ 0.759152] io scheduler kyber registered
[ 0.765018] pinctrl-single 4301c000.pinmux: 70 pins, size 280
[ 0.771600] pinctrl-single 11c000.pinmux: 185 pins, size 740
[ 0.777546] pinctrl-single 11c2e8.pinmux: 9 pins, size 36
[ 0.784280] pinctrl-single a40000.timesync_router: 512 pins, size 2048
[ 0.799736] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled
[ 0.822940] brd: module loaded
[ 0.833392] loop: module loaded
[ 0.838986] libphy: Fixed MDIO Bus: probed
[ 0.843750] tun: Universal TUN/TAP device driver, 1.6
[ 0.849722] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 0.857750] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 0.863865] sky2: driver version 1.30
[ 0.869092] VFIO - User Level meta-driver version: 0.3
[ 0.875296] i2c /dev entries driver
[ 0.880324] sdhci: Secure Digital Host Controller Interface driver
[ 0.886664] sdhci: Copyright(c) Pierre Ossman
[ 0.891597] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.898763] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.905016] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: invalid resource
[ 0.915869] optee: probing for conduit method from DT.
I/TC: Dynamic shared memory is disabled
[ 0.921163] optee: revision 3.4 (251f7c63)
[ 0.925102] optee: initialized driver
[ 0.934489] NET: Registered protocol family 17
[ 0.939127] 9pnet: Installing 9P2000 support
[ 0.943568] Key type dns_resolver registered
[ 0.948579] registered taskstats version 1
[ 0.952784] Loading compiled-in X.509 certificates
[ 0.958756] davinci_gpio 42110000.wkup_gpio0: IRQ not populated, err = -517
[ 0.966332] davinci_gpio 600000.main_gpio0: IRQ not populated, err = -517
[ 0.973542] davinci_gpio 601000.main_gpio1: IRQ not populated, err = -517
[ 0.990720] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: invalid resource
[ 1.000723] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
[ 1.034061] random: fast init done
[ 1.536881] davinci_gpio 42110000.wkup_gpio0: IRQ not populated, err = -517
[ 1.544432] davinci_gpio 600000.main_gpio0: IRQ not populated, err = -517
[ 1.551632] davinci_gpio 601000.main_gpio1: IRQ not populated, err = -517
[ 1.560032] omap_i2c 42120000.i2c: bus 0 rev0.12 at 400 kHz
[ 1.566505] omap_i2c 40b00000.i2c: bus 1 rev0.12 at 100 kHz
[ 1.595957] omap_i2c 2000000.i2c: bus 2 rev0.12 at 400 kHz
[ 1.602315] omap_i2c 2010000.i2c: bus 3 rev0.12 at 400 kHz
[ 1.608638] omap_i2c 2020000.i2c: bus 4 rev0.12 at 400 kHz
[ 1.614936] omap_i2c 2030000.i2c: bus 5 rev0.12 at 100 kHz
[ 1.629264] keystone-pcie 5500000.pcie: Linked as a consumer to phy-900000.serdes.0
[ 1.637145] keystone-pcie 5500000.pcie: Linked as a consumer to phy-910000.serdes.1
[ 1.650432] keystone-pcie 5500000.pcie: host bridge /interconnect@100000/pcie@5500000 ranges:
[ 1.659193] keystone-pcie 5500000.pcie: IO 0x10020000..0x1002ffff -> 0x00000000
[ 1.666959] keystone-pcie 5500000.pcie: MEM 0x10030000..0x17ffffff -> 0x10030000
[ 2.675033] keystone-pcie 5500000.pcie: Phy link never came up
[ 2.681137] keystone-pcie 5500000.pcie: PCI host bridge to bus 0000:00
[ 2.687832] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.693453] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.699786] pci_bus 0000:00: root bus resource [mem 0x10030000-0x17ffffff]
[ 2.715732] pci 0000:00:00.0: BAR 6: assigned [mem 0x10030000-0x1003ffff pref]
[ 2.723141] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.729574] k3-ringacc 2b800000.ringacc: Ring Accelerator probed rings:286, gp-rings[96,160] sci-dev-id:195
[ 2.739573] k3-ringacc 2b800000.ringacc: dma-ring-reset-quirk: enabled
[ 2.746261] k3-ringacc 2b800000.ringacc: RA Proxy rev. 66344100, num_proxies:64
[ 2.754122] k3-ringacc 3c000000.ringacc: Ring Accelerator probed rings:818, gp-rings[304,464] sci-dev-id:187
[ 2.764201] k3-ringacc 3c000000.ringacc: dma-ring-reset-quirk: enabled
[ 2.770888] k3-ringacc 3c000000.ringacc: RA Proxy rev. 66344100, num_proxies:64
[ 2.778688] omap8250 40a00000.serial: PM domain ti_sci_pd will not be powered off
[ 2.786771] 40a00000.serial: ttyS1 at MMIO 0x40a00000 (irq = 8, base_baud = 6000000) is a 8250
[ 2.796485] 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 22, base_baud = 3000000) is a 8250
[ 2.805262] console [ttyS2] enabled
[ 2.805262] console [ttyS2] enabled
[ 2.812317] bootconsole [ns16550a0] disabled
[ 2.812317] bootconsole [ns16550a0] disabled
[ 2.821698] 2810000.serial: ttyS3 at MMIO 0x2810000 (irq = 23, base_baud = 3000000) is a 8250
[ 2.830980] 2820000.serial: ttyS4 at MMIO 0x2820000 (irq = 24, base_baud = 3000000) is a 8250
[ 2.841989] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes)
[ 2.848199] 7 cmdlinepart partitions found on MTD device 47040000.spi.0
[ 2.854816] Creating 7 MTD partitions on "47040000.spi.0":
[ 2.860306] 0x000000000000-0x000000080000 : "ospi.tiboot3"
[ 2.866652] 0x000000080000-0x000000280000 : "ospi.tispl"
[ 2.872679] 0x000000280000-0x000000680000 : "ospi.u-boot"
[ 2.878746] 0x000000680000-0x0000006a0000 : "ospi.env"
[ 2.884567] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup"
[ 2.890940] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw"
[ 2.896867] 0x000000800000-0x000004000000 : "ospi.rootfs"
[ 3.010892] cadence-qspi 47040000.spi: Cadence QSPI NOR probe failed -517
[ 3.026126] am65-cpsw-nuss 46000000.ethernet: rx-flow-id-base is not set -22
[ 3.033294] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA07100, cpsw version 0x6BA80100 Ports: 2
[ 3.044831] UDMA has not been proped
[ 3.048424] am65-cpsw-nuss 46000000.ethernet: Failed to request tx dma channel -517
[ 3.058722] am65-cpts 310d0000.cpts: CPTS ver 0x4e8a2109, freq:200000000, add_val:4 pps:0
[ 3.067470] thermal thermal_zone1: failed to read out thermal zone (-22)
[ 3.074197] thermal thermal_zone2: failed to read out thermal zone (-22)
[ 3.081632] OF: /interconnect@100000/interconnect@28380000/rti@40610000: arguments longer than property
[ 3.091042] keystone-wdt 40610000.rti: heartbeat 60 sec
[ 3.097194] mmc0: Unknown controller version (4). You may experience problems.
[ 3.135534] mmc0: SDHCI controller on 4f80000.sdhci [4f80000.sdhci] using ADMA 64-bit
[ 3.144141] mmc1: Unknown controller version (4). You may experience problems.
[ 3.181274] mmc1: SDHCI controller on 4fa0000.sdhci [4fa0000.sdhci] using ADMA 64-bit
[ 3.190485] mmc0: new HS200 MMC card at address 0001
[ 3.196594] mmcblk0: mmc0:0001 S0J56X 14.8 GiB
[ 3.202149] mmcblk0boot0: mmc0:0001 S0J56X partition 1 31.5 MiB
[ 3.211962] mmcblk0boot1: mmc0:0001 S0J56X partition 2 31.5 MiB
[ 3.220833] mmcblk0rpmb: mmc0:0001 S0J56X partition 3 4.00 MiB, chardev (243:0)
[ 3.254636] mmc1: Problem switching card into high-speed mode!
[ 3.262165] omap-mailbox 31f80000.mailbox: omap mailbox rev 0x66fc5900
[ 3.268878] mmc1: new SDHC card at address 0001
[ 3.273643] omap-mailbox 31f81000.mailbox: omap mailbox rev 0x66fc5900
[ 3.281344] mmcblk1: mmc1:0001 SD32G 29.0 GiB
[ 3.286797] ti-udma 285c0000.udmap: Channels: 96 (tchan: 48, echan: 0, rchan: 48, rflow: 96)
[ 3.295327] mmcblk1: p1 p2
[ 3.305180] ti-udma 31150000.udmap: Channels: 267 (tchan: 120, echan: 32, rchan: 150, rflow: 300)
[ 3.330155] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes)
[ 3.336373] 7 cmdlinepart partitions found on MTD device 47040000.spi.0
[ 3.342987] Creating 7 MTD partitions on "47040000.spi.0":
[ 3.348478] 0x000000000000-0x000000080000 : "ospi.tiboot3"
[ 3.354831] 0x000000080000-0x000000280000 : "ospi.tispl"
[ 3.360786] 0x000000280000-0x000000680000 : "ospi.u-boot"
[ 3.366812] 0x000000680000-0x0000006a0000 : "ospi.env"
[ 3.372623] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup"
[ 3.379031] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw"
[ 3.384973] 0x000000800000-0x000004000000 : "ospi.rootfs"
[ 3.398072] m25p80 spi7.0: n25q128a13 (16384 Kbytes)
[ 3.404331] am65-cpsw-nuss 46000000.ethernet: rx-flow-id-base is not set -22
[ 3.411495] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA07100, cpsw version 0x6BA80100 Ports: 2
[ 3.431744] am65-cpsw-nuss 46000000.ethernet: set new flow-id-base 48
[ 3.445159] pps pps0: new PPS source ptp1
[ 3.449416] am65-cpsw-nuss 46000000.ethernet: CPTS ver 0x4e8a2109, freq:200000000, add_val:4 pps:1
[ 3.458412] am65-cpsw-nuss 46000000.ethernet: initialized cpsw ale version 0.4
[ 3.465634] am65-cpsw-nuss 46000000.ethernet: ALE Table size 64
[ 3.510551] am65-cpsw-nuss 46000000.ethernet: davinci mdio revision 9.7, bus freq 1000000
[ 3.518728] libphy: 46000000.ethernet: probed
[ 3.526466] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 3.533482] hctosys: unable to open rtc device (rtc0)
[ 3.635821] ALSA device list:
[ 3.638807] No soundcards found.
[ 3.824205] EXT4-fs (mmcblk1p2): 2 orphan inodes deleted
[ 3.829570] EXT4-fs (mmcblk1p2): recovery complete
[ 3.862472] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.870627] VFS: Mounted root (ext4 filesystem) on device 179:98.
[ 3.891838] devtmpfs: mounted
[ 3.895116] Freeing unused kernel memory: 576K
[ 3.899605] Run /sbin/init as init process
[ 4.575035] systemd[1]: System time before build time, advancing clock.
[ 4.765774] NET: Registered protocol family 10
[ 4.771371] Segment Routing with IPv6
[ 4.840300] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
[ 4.862060] systemd[1]: Detected architecture arm64.
Welcome to Arago 2019.05!
[ 4.904061] systemd[1]: Set hostname to <am65xx-evm>.
[ 5.224733] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 5.241797] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 5.572522] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.579590] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 5.602704] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.612085] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 5.630677] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.637571] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 5.654649] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 5.670829] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Listening on Journal Socket.
Starting Create list of required st�cce nodes for the current kernel...
[ OK ] Started Hardware RNG Entropy Gatherer Daemon.
Starting Remount Root and Kernel File Systems...
Starting Load Kernel Modules...
[ 5.802285] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
Mounting Huge Pages File System...
Mounting Kernel Debug File System...
[ 5.827867] cryptodev: loading out-of-tree module taints kernel.
[ OK ] Listening on udev Kernel Socket.
[ 5.843172] cryptodev: driver 1.9 loaded.
[ OK ] Created slice User and Session Slice.
[ OK ] Reached target Slices.
Starting Journal Service...
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Reached target Paths.
Mounting POSIX Message Queue File System...
[ OK ] Reached target Swap.
Mounting Temporary Directory (/tmp)...
[ OK ] Listening on Process Core Dump Socket.
[ OK ] Listening on udev Control Socket.
Starting udev Coldplug all Devices...
[ OK ] Started Journal Service.
[ OK ] Started Create list of required sta�cvice nodes for the current kernel.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started Load Kernel Modules.
[ OK ] Mounted Huge Pages File System.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Temporary Directory (/tmp).
Mounting Kernel Configuration File System...
Starting Apply Kernel Variables...
Starting Create Static Device Nodes in /dev...
Starting Flush Journal to Persistent Storage...
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started Apply Kernel Variables.
[ 6.291374] systemd-journald[165]: Received request to flush runtime journal from PID 1
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile...
[ OK ] Reached target Containers.
Mounting /media/ram...
Starting udev Kernel Device Manager...
[ OK ] Mounted /var/volatile.
[ OK ] Mounted /media/ram.
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
Starting Load/Save Random Seed...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Update UTMP about System Boot/Shutdown.
Starting Network Service...
[ OK ] Started udev Coldplug all Devices.
[ 6.893859] input: gpio-decoder as /devices/platform/gpio-decoder/input/input1
[ OK ] Started Network Service.
Starting Network Name Resolution...
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Time Synchronized.
[ OK ] Reached target System Initialization.
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Listening on D-Bus System Message Bus Socket.
Starting Reboot and dump vmcore via kexec...
[ OK ] Started Daily rotation of log files.
[ OK ] Reached target Timers.
[ OK ] Listening on dropbear.socket.[ 7.194781] omap_rng 4e10000.trng: Random Number Generator ver. 230b34c
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting RPC Bind Service...
[ OK ] Started D-Bus System Message Bus.
[ 7.339638] CAN device driver interface
Starting TI IPC Daemon...
[ 7.344305] [drm] Initialized pvr 1.17.4948957 20110701 for 7000000.gpu on minor 0
Starting Login Service...
[ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf.
Starting Print notice about GPLv3 packages...
[ OK ] Started irqbalance daemon.
Starting rng-tools.service...
[ 7.457515] m_can 40528000.mcan: m_can device registered (irq=17, version=32)
[ 7.479128] m_can 40568000.mcan: m_can device registered (irq=19, version=32)
[ OK ] Started Periodic Command Scheduler.
[ OK ] Started Job spooling tools.
[ OK ] Started Network Name Resolution.
[ OK ] Found device /dev/ttyS2.
[ 7.587840] k3_r5_rproc interconnect@100000:interconnect@28380000:r5fss@41000000: creating child devices for R5F cores
[ OK ] [ 7.602752] platform 41000000.r5f: assigned reserved memory node r5f-dma-memory@9c000000
Started TI IPC Daemon.
[ 7.612634] remoteproc remoteproc0: 41000000.r5f is available
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Reached target Network.
Starting Simple Network Management Protocol (SNMP) Daemon....
Starting Lightning Fast Webserver With Light System Requirements...
Starting Permit User Sessions...
[ 8.141130] random: crng init done
[ 8.144722] random: 7 urandom warning(s) missed due to ratelimiting
[ 8.166484] TI DP83867 k3-cpsw-mdio:00: attached PHY driver [TI DP83867] (mii_bus:phy_addr=k3-cpsw-mdio:00, irq=POLL)
[ 8.178408] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.474572] davinci_mdio b032400.mdio: davinci mdio revision 1.7, bus freq 1000000
[ 8.482184] libphy: b032400.mdio: probed
[ 8.486771] remoteproc remoteproc0: powering up 41000000.r5f
[ 8.492544] remoteproc remoteproc0: Booting fw image am65x-mcu-r5f0_0-fw, size 4050720
[ 8.511728] platform 41000000.r5f: booting R5F core using boot addr = 0x0
[ 8.512383] davinci_mdio b032400.mdio: phy[0]: device b032400.mdio:00, driver TI DP83867
[ 8.519810] remoteproc remoteproc0: registered virtio0 (type 7)
[ 8.527093] davinci_mdio b032400.mdio: phy[3]: device b032400.mdio:03, driver TI DP83867
[ 8.536265] remoteproc remoteproc0: remote processor 41000000.r5f is now up
[ 8.590708] davinci_mdio b132400.mdio: davinci mdio revision 1.7, bus freq 1000000
[ 8.598823] libphy: b132400.mdio: probed
[ 8.627140] davinci_mdio b132400.mdio: phy[0]: device b132400.mdio:00, driver TI DP83867
[ 8.638665] davinci_mdio b132400.mdio: phy[3]: device b132400.mdio:03, driver TI DP83867
[ 8.730897] davinci_mdio b232400.mdio: davinci mdio revision 1.7, bus freq 1000000
[ 8.741863] libphy: b232400.mdio: probed
[ 8.772986] davinci_mdio b232400.mdio: phy[0]: device b232400.mdio:00, driver TI DP83867
[ 8.786079] davinci_mdio b232400.mdio: phy[3]: device b232400.mdio:03, driver TI DP83867
[ 8.825901] remoteproc remoteproc1: b034000.pru is available
[ 8.838703] pru-rproc b034000.pru: PRU rproc node pru@b034000 probed successfully
[ 8.856329] remoteproc remoteproc2: b004000.rtu is available
[ 8.864371] pru-rproc b004000.rtu: PRU rproc node rtu@b004000 probed successfully
[ 8.879450] remoteproc remoteproc3: b038000.pru is available
[ 8.890371] pru-rproc b038000.pru: PRU rproc node pru@b038000 probed successfully
[ 8.901594] remoteproc remoteproc4: b006000.rtu is available
[ 8.914291] pru-rproc b006000.rtu: PRU rproc node rtu@b006000 probed successfully
[ 8.934070] remoteproc remoteproc5: b134000.pru is available
[ 8.942970] pru-rproc b134000.pru: PRU rproc node pru@b134000 probed successfully
[ 8.953268] remoteproc remoteproc6: b104000.rtu is available
[ 8.973331] pru-rproc b104000.rtu: PRU rproc node rtu@b104000 probed successfully
[ 8.983702] remoteproc remoteproc7: b138000.pru is available
[ 9.000344] pru-rproc b138000.pru: PRU rproc node pru@b138000 probed successfully
[ 9.008837] remoteproc remoteproc8: b106000.rtu is available
[ 9.015295] pru-rproc b106000.rtu: PRU rproc node rtu@b106000 probed successfully
[ 9.024930] remoteproc remoteproc9: b234000.pru is available
[ 9.030929] pru-rproc b234000.pru: PRU rproc node pru@b234000 probed successfully
[ 9.039396] remoteproc remoteproc10: b204000.rtu is available
[ 9.051191] pru-rproc b204000.rtu: PRU rproc node rtu@b204000 probed successfully
[ 9.061085] remoteproc remoteproc11: b238000.pru is available
[ 9.067236] pru-rproc b238000.pru: PRU rproc node pru@b238000 probed successfully
[ 9.085033] remoteproc remoteproc12: b206000.rtu is available
[ 9.091154] pru-rproc b206000.rtu: PRU rproc node rtu@b206000 probed successfully
[ 9.187974] am65-cpsw-nuss 46000000.ethernet eth0: Link is Down
[ 9.290881] icssg-prueth pruss1_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0
[ OK ] Started Reboot and dump vmcore via kexec.
[ OK ] Started RPC Bind Service.
[ OK ] Started rng-tools.service.
[ OK ] Started Lightning Fast Webserver With Light System Requirements.
[ OK ] Started Permit User Sessions.
[ 9.440658] icssg-prueth pruss0_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0
[ 9.538746] icssg-prueth pruss2_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0
[ 9.550725] NET: Registered protocol family 15
[ 9.617299] dwc3 4010000.usb: Failed to get clk 'ref': -2
[ 9.629043] dwc3 4030000.usb: Failed to get clk 'ref': -2
[ 9.655092] OF: graph: no port node found in /interconnect@100000/phy@4110000
[ 9.782951] virtio_rpmsg_bus virtio0: rpmsg host is online
[ 9.784004] virtio_rpmsg_bus virtio0: creating channel rpmsg-proto addr 0x3d
[ 9.811483] Initializing XFRM netlink socket
[ 10.059457] NET: Registered protocol family 45
[ 10.130093] icssg-prueth pruss0_eth eth3: flow id base = 150
[ 10.141069] icssg-prueth pruss0_eth eth3: mgm flow id base = 154
[ 10.153704] remoteproc remoteproc1: powering up b034000.pru
[ 10.177218] usbcore: registered new interface driver usbfs
[ 10.183136] usbcore: registered new interface driver hub
[ 10.188723] usbcore: registered new device driver usb
[ 10.216580] remoteproc remoteproc1: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 14868
[ 10.226014] remoteproc remoteproc1: remote processor b034000.pru is now up
[ 10.232989] remoteproc remoteproc2: powering up b004000.rtu
[ 10.260443] remoteproc remoteproc2: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15488
[ 10.269519] remoteproc remoteproc2: remote processor b004000.rtu is now up
[ 10.277610] net eth3: started
[ 10.281330] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 10.316672] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 10.323086] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1
[ 10.331456] xhci-hcd xhci-hcd.2.auto: hcc params 0x0298fe6d hci version 0x110 quirks 0x0000000000010010
[ 10.341420] xhci-hcd xhci-hcd.2.auto: irq 309, io mem 0x04010000
[ 10.347449] icssg-prueth pruss2_eth eth5: flow id base = 157
[ 10.353741] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 10.362081] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.369402] usb usb1: Product: xHCI Host Controller
[ 10.374341] usb usb1: Manufacturer: Linux 4.19.38-g4dae378bbe xhci-hcd
[ 10.380954] usb usb1: SerialNumber: xhci-hcd.2.auto
[ 10.386681] hub 1-0:1.0: USB hub found
[ 10.390644] hub 1-0:1.0: 1 port detected
[ 10.395668] icssg-prueth pruss2_eth eth5: mgm flow id base = 161
[ 10.396335] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 10.404459] remoteproc remoteproc9: powering up b234000.pru
[ 10.407753] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2
[ 10.413283] remoteproc remoteproc9: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 14868
[ 10.421484] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 10.429898] remoteproc remoteproc9: remote processor b234000.pru is now up
[ 10.436812] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 10.443210] remoteproc remoteproc10: powering up b204000.rtu
[ 10.451562] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[ 10.457119] remoteproc remoteproc10: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15488
[ 10.465323] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.474440] remoteproc remoteproc10: remote processor b204000.rtu is now up
[ 10.481604] usb usb2: Product: xHCI Host Controller
[ 10.481617] usb usb2: Manufacturer: Linux 4.19.38-g4dae378bbe xhci-hcd
[ 10.490040] net eth5: started
[ 10.493535] usb usb2: SerialNumber: xhci-hcd.2.auto
[ 10.495138] hub 2-0:1.0: USB hub found
[ 10.500355] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
[ 10.503153] hub 2-0:1.0: 1 port detected
[ 10.513816] icssg-prueth pruss1_eth eth2: flow id base = 164
[ 10.534776] icssg-prueth pruss1_eth eth2: mgm flow id base = 168
[ 10.544271] remoteproc remoteproc7: powering up b138000.pru
[ 10.571391] remoteproc remoteproc7: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 14868
[ 10.580443] remoteproc remoteproc7: remote processor b138000.pru is now up
[ 10.588988] remoteproc remoteproc8: powering up b106000.rtu
[ OK ] Started Login Service.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS2.
[ OK ] Reached targ[ 10.616283] remoteproc remoteproc8: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15488
et Login Prompts.
[ 10.628978] remoteproc remoteproc8: remote processor b106000.rtu is now up
Starting Synchronize System and HW clocks...
[ 10.638687] net eth2: started
Starting rc.pvr.service...[ 10.645621] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 10.663185] icssg-prueth pruss2_eth eth6: flow id base = 171
[ 10.673368] icssg-prueth pruss2_eth eth6: mgm flow id base = 175
[ 10.683206] remoteproc remoteproc11: powering up b238000.pru
[ OK ] [ 10.689577] remoteproc remoteproc11: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 14868
Started NFS status monitor for NFSv2/3 locking..
[ 10.700196] remoteproc remoteproc11: remote processor b238000.pru is now up
[FAILED] Failed to start Synchronize System and HW c[ 10.712461] remoteproc remoteproc12: powering up b206000.rtu
locks.
[ 10.723354] remoteproc remoteproc12: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15488
[ 10.737809] remoteproc remoteproc12: remote processor b206000.rtu is now up
[ 10.746442] net eth6: started
[ 10.749684] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready
[ 10.764224] icssg-prueth pruss1_eth eth1: flow id base = 178
[ 10.774394] icssg-prueth pruss1_eth eth1: mgm flow id base = 182
[ 10.784253] remoteproc remoteproc5: powering up b134000.pru
[ 10.790597] remoteproc remoteproc5: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 14868
[ 10.799654] remoteproc remoteproc5: remote processor b134000.pru is now up
[ 10.806614] remoteproc remoteproc6: powering up b104000.rtu
[ 10.812292] remoteproc remoteproc6: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15488
[ 10.821449] remoteproc remoteproc6: remote processor b104000.rtu is now up
[ 10.829479] net eth1: started
[ 10.832696] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 10.844169] icssg-prueth pruss0_eth eth4: flow id base = 185
[ 10.853940] icssg-prueth pruss0_eth eth4: mgm flow id base = 189
[ 10.864209] remoteproc remoteproc3: powering up b038000.pru
[ 10.870358] remoteproc remoteproc3: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 14868
[ 10.879434] remoteproc remoteproc3: remote processor b038000.pru is now up
[ 10.886447] remoteproc remoteproc4: powering up b006000.rtu
[ 10.892545] remoteproc remoteproc4: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15488
[ 10.901582] remoteproc remoteproc4: remote processor b006000.rtu is now up
[ 10.909788] net eth4: started
[ 10.913010] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
[ 11.044795] PVR_K: UM DDK-(4948957) and KM DDK-(4948957) match. [ OK ]
[ OK ] Started rc.pvr.service.
Starting weston.service...
[ OK ] Started weston.service.
Starting Matrix GUI...
Starting telnetd.service...
[ OK ] Started telnetd.service.
Starting thttpd.service...
[ OK ] Started Matrix GUI.
[ OK ] Started thttpd.service.
Starting thermal-zone-init.service...
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ OK ] Started thermal-zone-init.service.
[ OK ] Found device /dev/mmcblk1p1.
Starting File System Check on /dev/mmcblk1p1...
[ OK ] Started Simple Network Management Protocol (SNMP) Daemon..
[ OK ] Started File System Check on /dev/mmcblk1p1.
Mounting /run/media/mmcblk1p1...
[ OK ] Mounted /run/media/mmcblk1p1.
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org am65xx-evm ttyS2
Arago 2019.05 am65xx-evm ttyS2
am65xx-evm login: ***************************************************************
***************************************************************
NOTICE: This file system contains the following GPLv3 packages:
autoconf
bash
bc
binutils
cifs-utils
cpio
cpp-symlinks
cpp
dosfstools
elfutils
g++-symlinks
g++
gawk
gcc-symlinks
gcc
gdb
gdbserver
gettext
glmark2
gstreamer1.0-libav
gzip
hidapi
libbfd
libdw1
libelf1
libgdbm-compat4
libgdbm6
libgettextlib
libgettextsrc
libgmp10
libidn2-0
libmpc3
libmpfr6
libreadline7
libunistring2
m4
make
nettle
parted
pdm-anomaly-detection
which
If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution. This can be done using
the opkg remove command. i.e.:
opkg remove <package>
Where <package> is the name printed in the list above
NOTE: If the package is a dependency of another package you
will be notified of the dependent packages. You should
use the --force-removal-of-dependent-packages option to
also remove the dependent packages as well
***************************************************************
***************************************************************
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
read_dqs_training:ERROR: Read DQS Gate training failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
read_dqs_training:ERROR: Read DQS Gate training failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
read_dqs_training:ERROR: Read DQS Gate training failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
rest_training: ERROR: Write Leveling adjustment failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
rest_training: ERROR: Write Leveling adjustment failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
rest_training: ERROR: Write Leveling adjustment failed
DRAM init failed: -22
resetting ...
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:46:46 +0000)
SYSFW ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
Trying to boot from MMC2
Starting ATF on ARM64 core...
NOTICE: BL31: v2.1(release):ti2019.01-rc2
NOTICE: BL31: Built : 04:28:26, Jul 7 2019
I/TC:
I/TC: OP-TEE version: 3.2.0-583-g251f7c6-dev #1 Sun Jul 7 04:40:43 UTC 2019 aarch64
I/TC: Initialized
U-Boot SPL 2019.01-g8b90adfb16 (Jul 07 2019 - 05:09:26 +0000)
detected AM6-IDKAPPEVM
detected SER-PCIE2LEVM
Trying to boot from MMC2
U-Boot 2019.01-g8b90adfb16 (Jul 07 2019 - 05:09:26 +0000)
Model: Texas Instruments AM654 Base Board
DRAM: 4 GiB
MMC: sdhci@4f80000: 0, sdhci@04FA0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
detected AM6-IDKAPPEVM
detected SER-PCIE2LEVM
Net: eth2: pruss0_eth
Warning: cpsw_nuss@046000000 using MAC address from ROM
, eth0: cpsw_nuss@046000000, eth1: pruss2_eth
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
SD/MMC found on device 1
** Unable to read file boot.scr **
1490 bytes read in 3 ms (484.4 KiB/s)
Loaded env from uEnv.txt
Importing environment from mmc1 ...
Running uenvcmd ...
1 bytes read in 1 ms (1000 Bytes/s)
Already setup.
12632072 bytes read in 1063 ms (11.3 MiB/s)
71809 bytes read in 10 ms (6.8 MiB/s)
11402 bytes read in 3 ms (3.6 MiB/s)
2084 bytes read in 2 ms (1017.6 KiB/s)
## Flattened Device Tree blob at 82000000
Booting using the fdt blob at 0x82000000
Loading Device Tree to 00000000fddb7000, end 00000000fdecbfff ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 4.19.38-g4dae378bbe (oe-user@oe-host) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #1 SMP PREEMPT Sun Jul 7 03:42:51 UTC 2019
[ 0.000000] Machine model: Texas Instruments AM654 Base Board
[ 0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '')
[ 0.000000] bootconsole [ns16550a0] enabled
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009b000000, size 1 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@9b000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009b100000, size 15 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-memory@9b100000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009c000000, size 1 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@9c000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000009c100000, size 7 MiB
[ 0.000000] OF: reserved mem: initialized node r5f-memory@9c100000, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 512 MiB at 0x00000000c0000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x3e4 with crng_init=0
[ 0.000000] percpu: Embedded 2 pages/cpu s48536 r8192 d74344 u131072
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Speculative Store Bypass Disable mitigation not required
[ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64704
[ 0.000000] Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),128k(ospi.env),128k(ospi.env.backup),1m(ospi.sysfw),-@8m(ospi.rootfs) root=PARTUUID=5d2ac6ad-02 rw rootfstype=ext4 rootwait
[ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes)
[ 0.000000] software IO TLB: mapped [mem 0xf9db0000-0xfddb0000] (64MB)
[ 0.000000] Memory: 3529856K/4145152K available (8062K kernel code, 752K rwdata, 2880K rodata, 576K init, 614K bss, 91008K reserved, 524288K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] ITS [mem 0x01820000-0x0182ffff]
[ 0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS
[ 0.000000] ITS@0x0000000001820000: allocated 1048576 Devices @8c0800000 (flat, esz 8, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x00000008c00c0000
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001880000
[ 0.000000] CPU0: using LPI pending table @0x00000008c00d0000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns
[ 0.000006] sched_clock: 56 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns
[ 0.008702] Console: colour dummy device 80x25
[ 0.013297] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=800000)
[ 0.023986] pid_max: default: 32768 minimum: 301
[ 0.028815] Security Framework initialized
[ 0.033076] Mount-cache hash table entries: 8192 (order: 0, 65536 bytes)
[ 0.039959] Mountpoint-cache hash table entries: 8192 (order: 0, 65536 bytes)
[ 0.071399] ASID allocator initialised with 32768 entries
[ 0.084967] rcu: Hierarchical SRCU implementation.
[ 0.098037] Platform MSI: gic-its@18200000 domain created
[ 0.103862] PCI/MSI: /interconnect@100000/interrupt-controller@1800000/gic-its@18200000 domain created
[ 0.121429] smp: Bringing up secondary CPUs ...
[ 0.158558] Detected VIPT I-cache on CPU1
[ 0.158595] GICv3: CPU1: found redistributor 1 region 0:0x00000000018a0000
[ 0.158652] CPU1: using LPI pending table @0x00000008c0330000
[ 0.158696] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.220242] Detected VIPT I-cache on CPU2
[ 0.220285] GICv3: CPU2: found redistributor 100 region 0:0x00000000018c0000
[ 0.220344] CPU2: using LPI pending table @0x00000008c03c0000
[ 0.220394] CPU2: Booted secondary processor 0x0000000100 [0x410fd034]
[ 0.252652] Detected VIPT I-cache on CPU3
[ 0.252678] GICv3: CPU3: found redistributor 101 region 0:0x00000000018e0000
[ 0.252733] CPU3: using LPI pending table @0x00000008c0450000
[ 0.252764] CPU3: Booted secondary processor 0x0000000101 [0x410fd034]
[ 0.252909] smp: Brought up 1 node, 4 CPUs
[ 0.328547] SMP: Total of 4 processors activated.
[ 0.333368] CPU features: detected: GIC system register CPU interface
[ 0.339979] CPU features: detected: 32-bit EL0 Support
[ 0.367850] CPU: All CPU(s) started at EL2
[ 0.372071] alternatives: patching kernel code
[ 0.378077] devtmpfs: initialized
[ 0.393257] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.403264] futex hash table entries: 1024 (order: 0, 65536 bytes)
[ 0.410949] pinctrl core: initialized pinctrl subsystem
[ 0.416937] NET: Registered protocol family 16
[ 0.422723] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
[ 0.430313] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.443728] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.452588] davinci_gpio 42110000.wkup_gpio0: IRQ not populated, err = -517
[ 0.466874] davinci_gpio 600000.main_gpio0: IRQ not populated, err = -517
[ 0.474082] davinci_gpio 601000.main_gpio1: IRQ not populated, err = -517
[ 0.492141] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.499017] HugeTLB registered 512 MiB page size, pre-allocated 0 pages
[ 0.507787] cryptd: max_cpu_qlen set to 1000
[ 0.513966] media: Linux media interface: v0.10
[ 0.518646] videodev: Linux video capture interface: v2.00
[ 0.524306] pps_core: LinuxPPS API ver. 1 registered
[ 0.529389] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.538751] PTP clock support registered
[ 0.542793] EDAC MC: Ver: 3.0.0
[ 0.547315] Advanced Linux Sound Architecture Driver Initialized.
[ 0.554501] clocksource: Switched to clocksource arch_sys_counter
[ 0.560951] VFS: Disk quotas dquot_6.6.0
[ 0.565061] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes)
[ 0.579349] NET: Registered protocol family 2
[ 0.584558] tcp_listen_portaddr_hash hash table entries: 4096 (order: 0, 65536 bytes)
[ 0.592717] TCP established hash table entries: 32768 (order: 2, 262144 bytes)
[ 0.600413] TCP bind hash table entries: 32768 (order: 3, 524288 bytes)
[ 0.607763] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.614623] UDP hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.620889] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.627767] NET: Registered protocol family 1
[ 0.632853] RPC: Registered named UNIX socket transport module.
[ 0.638932] RPC: Registered udp transport module.
[ 0.643750] RPC: Registered tcp transport module.
[ 0.648566] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.656336] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 0.669466] Initialise system trusted keyrings
[ 0.674296] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[ 0.686209] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.693044] NFS: Registering the id_resolver key type
[ 0.698259] Key type id_resolver registered
[ 0.702546] Key type id_legacy registered
[ 0.706669] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.713705] 9p: Installing v9fs 9p2000 file system support
[ 0.724559] Key type asymmetric registered
[ 0.728782] Asymmetric key parser 'x509' registered
[ 0.733839] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 0.741418] io scheduler noop registered
[ 0.745450] io scheduler deadline registered
[ 0.749962] io scheduler cfq registered (default)
[ 0.754792] io scheduler mq-deadline registered
[ 0.759435] io scheduler kyber registered
[ 0.765294] pinctrl-single 4301c000.pinmux: 70 pins, size 280
[ 0.771893] pinctrl-single 11c000.pinmux: 185 pins, size 740
[ 0.777836] pinctrl-single 11c2e8.pinmux: 9 pins, size 36
[ 0.784590] pinctrl-single a40000.timesync_router: 512 pins, size 2048
[ 0.800240] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled
[ 0.823584] brd: module loaded
[ 0.833961] loop: module loaded
[ 0.839651] libphy: Fixed MDIO Bus: probed
[ 0.844416] tun: Universal TUN/TAP device driver, 1.6
[ 0.850398] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 0.858432] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 0.864544] sky2: driver version 1.30
[ 0.869782] VFIO - User Level meta-driver version: 0.3
[ 0.875922] i2c /dev entries driver
[ 0.880910] sdhci: Secure Digital Host Controller Interface driver
[ 0.887252] sdhci: Copyright(c) Pierre Ossman
[ 0.892242] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.899430] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.905686] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: invalid resource
[ 0.916530] optee: probing for conduit method from DT.
I/TC: Dynamic shared memory is disabled
[ 0.921823] optee: revision 3.4 (251f7c63)
[ 0.925770] optee: initialized driver
[ 0.935167] NET: Registered protocol family 17
[ 0.939797] 9pnet: Installing 9P2000 support
[ 0.944236] Key type dns_resolver registered
[ 0.949260] registered taskstats version 1
[ 0.953469] Loading compiled-in X.509 certificates
[ 0.959423] davinci_gpio 42110000.wkup_gpio0: IRQ not populated, err = -517
[ 0.967014] davinci_gpio 600000.main_gpio0: IRQ not populated, err = -517
[ 0.974214] davinci_gpio 601000.main_gpio1: IRQ not populated, err = -517
[ 0.991367] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: invalid resource
[ 1.001387] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: ABI: 2.6 (firmware rev 0x0013 '19.4.1-v2019.04a (Curious Crow)')
[ 1.034656] random: fast init done
[ 1.539147] davinci_gpio 42110000.wkup_gpio0: IRQ not populated, err = -517
[ 1.546713] davinci_gpio 600000.main_gpio0: IRQ not populated, err = -517
[ 1.553913] davinci_gpio 601000.main_gpio1: IRQ not populated, err = -517
[ 1.562285] omap_i2c 42120000.i2c: bus 0 rev0.12 at 400 kHz
[ 1.568783] omap_i2c 40b00000.i2c: bus 1 rev0.12 at 100 kHz
[ 1.599885] omap_i2c 2000000.i2c: bus 2 rev0.12 at 400 kHz
[ 1.606286] omap_i2c 2010000.i2c: bus 3 rev0.12 at 400 kHz
[ 1.612657] omap_i2c 2020000.i2c: bus 4 rev0.12 at 400 kHz
[ 1.618974] omap_i2c 2030000.i2c: bus 5 rev0.12 at 100 kHz
[ 1.633119] keystone-pcie 5500000.pcie: Linked as a consumer to phy-900000.serdes.0
[ 1.640999] keystone-pcie 5500000.pcie: Linked as a consumer to phy-910000.serdes.1
[ 1.654306] keystone-pcie 5500000.pcie: host bridge /interconnect@100000/pcie@5500000 ranges:
[ 1.663066] keystone-pcie 5500000.pcie: IO 0x10020000..0x1002ffff -> 0x00000000
[ 1.670831] keystone-pcie 5500000.pcie: MEM 0x10030000..0x17ffffff -> 0x10030000
[ 2.678911] keystone-pcie 5500000.pcie: Phy link never came up
[ 2.685017] keystone-pcie 5500000.pcie: PCI host bridge to bus 0000:00
[ 2.691711] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.697334] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 2.703666] pci_bus 0000:00: root bus resource [mem 0x10030000-0x17ffffff]
[ 2.719627] pci 0000:00:00.0: BAR 6: assigned [mem 0x10030000-0x1003ffff pref]
[ 2.727034] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.733455] k3-ringacc 2b800000.ringacc: Ring Accelerator probed rings:286, gp-rings[96,160] sci-dev-id:195
[ 2.743447] k3-ringacc 2b800000.ringacc: dma-ring-reset-quirk: enabled
[ 2.750135] k3-ringacc 2b800000.ringacc: RA Proxy rev. 66344100, num_proxies:64
[ 2.758001] k3-ringacc 3c000000.ringacc: Ring Accelerator probed rings:818, gp-rings[304,464] sci-dev-id:187
[ 2.768083] k3-ringacc 3c000000.ringacc: dma-ring-reset-quirk: enabled
[ 2.774771] k3-ringacc 3c000000.ringacc: RA Proxy rev. 66344100, num_proxies:64
[ 2.782579] omap8250 40a00000.serial: PM domain ti_sci_pd will not be powered off
[ 2.790685] 40a00000.serial: ttyS1 at MMIO 0x40a00000 (irq = 8, base_baud = 6000000) is a 8250
[ 2.800432] 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 22, base_baud = 3000000) is a 8250
[ 2.809215] console [ttyS2] enabled
[ 2.809215] console [ttyS2] enabled
[ 2.816270] bootconsole [ns16550a0] disabled
[ 2.816270] bootconsole [ns16550a0] disabled
[ 2.825657] 2810000.serial: ttyS3 at MMIO 0x2810000 (irq = 23, base_baud = 3000000) is a 8250
[ 2.834947] 2820000.serial: ttyS4 at MMIO 0x2820000 (irq = 24, base_baud = 3000000) is a 8250
[ 2.845954] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes)
[ 2.852166] 7 cmdlinepart partitions found on MTD device 47040000.spi.0
[ 2.858787] Creating 7 MTD partitions on "47040000.spi.0":
[ 2.864276] 0x000000000000-0x000000080000 : "ospi.tiboot3"
[ 2.870638] 0x000000080000-0x000000280000 : "ospi.tispl"
[ 2.876576] 0x000000280000-0x000000680000 : "ospi.u-boot"
[ 2.882615] 0x000000680000-0x0000006a0000 : "ospi.env"
[ 2.888388] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup"
[ 2.894814] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw"
[ 2.900735] 0x000000800000-0x000004000000 : "ospi.rootfs"
[ 3.122746] cadence-qspi 47040000.spi: Cadence QSPI NOR probe failed -517
[ 3.137465] am65-cpsw-nuss 46000000.ethernet: rx-flow-id-base is not set -22
[ 3.144632] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA07100, cpsw version 0x6BA80100 Ports: 2
[ 3.156234] UDMA has not been proped
[ 3.159834] am65-cpsw-nuss 46000000.ethernet: Failed to request tx dma channel -517
[ 3.169986] am65-cpts 310d0000.cpts: CPTS ver 0x4e8a2109, freq:200000000, add_val:4 pps:0
[ 3.178782] thermal thermal_zone1: failed to read out thermal zone (-22)
[ 3.185506] thermal thermal_zone2: failed to read out thermal zone (-22)
[ 3.192953] OF: /interconnect@100000/interconnect@28380000/rti@40610000: arguments longer than property
[ 3.202360] keystone-wdt 40610000.rti: heartbeat 60 sec
[ 3.208512] mmc0: Unknown controller version (4). You may experience problems.
[ 3.246852] mmc0: SDHCI controller on 4f80000.sdhci [4f80000.sdhci] using ADMA 64-bit
[ 3.255477] mmc1: Unknown controller version (4). You may experience problems.
[ 3.292616] mmc1: SDHCI controller on 4fa0000.sdhci [4fa0000.sdhci] using ADMA 64-bit
[ 3.301834] mmc0: new HS200 MMC card at address 0001
[ 3.307926] mmcblk0: mmc0:0001 S0J56X 14.8 GiB
[ 3.313472] mmcblk0boot0: mmc0:0001 S0J56X partition 1 31.5 MiB
[ 3.323216] mmcblk0boot1: mmc0:0001 S0J56X partition 2 31.5 MiB
[ 3.332245] mmcblk0rpmb: mmc0:0001 S0J56X partition 3 4.00 MiB, chardev (243:0)
[ 3.366925] mmc1: Problem switching card into high-speed mode!
[ 3.373955] omap-mailbox 31f80000.mailbox: omap mailbox rev 0x66fc5900
[ 3.380956] omap-mailbox 31f81000.mailbox: omap mailbox rev 0x66fc5900
[ 3.387509] mmc1: new SDHC card at address 0001
[ 3.393092] mmcblk1: mmc1:0001 SD32G 29.0 GiB
[ 3.398952] ti-udma 285c0000.udmap: Channels: 96 (tchan: 48, echan: 0, rchan: 48, rflow: 96)
[ 3.407488] mmcblk1: p1 p2
[ 3.417502] ti-udma 31150000.udmap: Channels: 267 (tchan: 120, echan: 32, rchan: 150, rflow: 300)
[ 3.442382] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes)
[ 3.448604] 7 cmdlinepart partitions found on MTD device 47040000.spi.0
[ 3.455219] Creating 7 MTD partitions on "47040000.spi.0":
[ 3.460708] 0x000000000000-0x000000080000 : "ospi.tiboot3"
[ 3.467102] 0x000000080000-0x000000280000 : "ospi.tispl"
[ 3.473137] 0x000000280000-0x000000680000 : "ospi.u-boot"
[ 3.479173] 0x000000680000-0x0000006a0000 : "ospi.env"
[ 3.484982] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup"
[ 3.491350] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw"
[ 3.497290] 0x000000800000-0x000004000000 : "ospi.rootfs"
[ 3.510397] m25p80 spi7.0: n25q128a13 (16384 Kbytes)
[ 3.516684] am65-cpsw-nuss 46000000.ethernet: rx-flow-id-base is not set -22
[ 3.523857] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA07100, cpsw version 0x6BA80100 Ports: 2
[ 3.544110] am65-cpsw-nuss 46000000.ethernet: set new flow-id-base 48
[ 3.557568] pps pps0: new PPS source ptp1
[ 3.561784] am65-cpsw-nuss 46000000.ethernet: CPTS ver 0x4e8a2109, freq:200000000, add_val:4 pps:1
[ 3.570763] am65-cpsw-nuss 46000000.ethernet: initialized cpsw ale version 0.4
[ 3.577984] am65-cpsw-nuss 46000000.ethernet: ALE Table size 64
[ 3.622516] am65-cpsw-nuss 46000000.ethernet: davinci mdio revision 9.7, bus freq 1000000
[ 3.630693] libphy: 46000000.ethernet: probed
[ 3.638425] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 3.645412] hctosys: unable to open rtc device (rtc0)
[ 3.747810] ALSA device list:
[ 3.750797] No soundcards found.
[ 4.055580] EXT4-fs (mmcblk1p2): 2 orphan inodes deleted
[ 4.060958] EXT4-fs (mmcblk1p2): recovery complete
[ 4.115574] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.123732] VFS: Mounted root (ext4 filesystem) on device 179:98.
[ 4.144773] devtmpfs: mounted
[ 4.148044] Freeing unused kernel memory: 576K
[ 4.152536] Run /sbin/init as init process
[ 4.827991] systemd[1]: System time before build time, advancing clock.
[ 5.047655] NET: Registered protocol family 10
[ 5.053221] Segment Routing with IPv6
[ 5.122143] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
[ 5.143884] systemd[1]: Detected architecture arm64.
Welcome to Arago 2019.05!
[ 5.188059] systemd[1]: Set hostname to <am65xx-evm>.
[ 5.508663] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 5.525723] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 5.856980] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.864016] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 5.886655] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.893520] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 5.910613] random: systemd: uninitialized urandom read (16 bytes read)
[ 5.917586] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 5.934643] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 5.965259] systemd[1]: Listening on Process Core Dump Socket.
[ OK ] Listening on Process Core Dump Socket.
[ OK ] Created slice system-getty.slice.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Listening on Journal Socket.
Mounting Temporary Directory (/tmp)...
Starting Create list of required st�cce nodes for the current kernel...
Starting Remount Root and Kernel File Systems...
[ 6.141882] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)
Starting Load Kernel Modules...
Mounting Kernel Debug File System...
[ 6.178454] cryptodev: loading out-of-tree module taints kernel.
[ OK ] Started Hardware RNG Entropy Gatherer Daemon[ 6.194408] cryptodev: driver 1.9 loaded.
.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Reached target Paths.
Mounting POSIX Message Queue File System...
[ OK ] Created slice User and Session Slice.
[ OK ] Reached target Slices.
[ OK ] Reached target Remote File Systems.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Listening on Journal Socket (/dev/log).
Starting Journal Service...
[ OK ] Listening on udev Control Socket.
Starting udev Coldplug all Devices...
Mounting Huge Pages File System...
[ OK ] Mounted Temporary Directory (/tmp).
[ OK ] Started Create list of required sta�cvice nodes for the current kernel.
[ OK ] Started Journal Service.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started Load Kernel Modules.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Huge Pages File System.
Mounting Kernel Configuration File System...
Starting Apply Kernel Variables...
Starting Flush Journal to Persistent Storage...
Starting Create Static Device Nodes in /dev...
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Started Apply Kernel Variables.
[ 6.663363] systemd-journald[165]: Received request to flush runtime journal from PID 1
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile...
Mounting /media/ram...
[ OK ] Reached target Containers.
[ OK ] Mounted /var/volatile.
[ OK ] Mounted /media/ram.
Starting Load/Save Random Seed...
[ OK ] Reached target Local File Systems.
Starting Create Volatile Files and Directories...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
Starting Network Time Synchronization...
[ OK ] Started udev Kernel Device Manager.
Starting Network Service...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started udev Coldplug all Devices.
[ 7.172973] input: gpio-decoder as /devices/platform/gpio-decoder/input/input1
[ OK ] Started Network Service.
Starting Network Name Resolution...
[ OK ] Found device /dev/ttyS2.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Initialization.
[ 7.432749] omap_rng 4e10000.trng: Random Number Generator ver. 230b34c
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Started Daily Cleanup of Temporary Directories.
Starting Reboot and dump vmcore via kexec...
[ 7.563933] [drm] Initialized pvr 1.17.4948957 20110701 for 7000000.gpu on minor 0
[ 7.594929] CAN device driver interface
[ OK ] Listening on dropbear.socket.
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ 7.691048] m_can 40528000.mcan: m_can device registered (irq=17, version=32)
[ 7.703094] m_can 40568000.mcan: m_can device registered (irq=19, version=32)
[ OK ] Started irqbalance daemon.
Starting rng-tools.service...
[ 7.767105] k3_r5_rproc interconnect@100000:interconnect@28380000:r5fss@41000000: creating child devices for R5F cores
[ OK ] Started Periodic Command Scheduler.
[ 7.795933] platform 41000000.r5f: assigned reserved memory node r5f-dma-memory@9c000000
Starting Login Service...
[ 7.815702] remoteproc remoteproc0: 41000000.r5f is available
[ OK ] Started D-Bus System Message Bus.
Starting TI IPC Daemon...
[ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf.
Starting Print notice about GPLv3 packages...
Starting RPC Bind Service...
[ OK ] Started Job spooling tools.
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Daily rotation of log files.
[ OK ] Reached target Timers.
[ OK ] Started Network Name Resolution.
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Reached target Network.
Starting Lightning Fast Webserver With Light System Requirements...
Starting Simple Network Management Protocol (SNMP) Daemon....
Starting Permit User Sessions...
[ 8.218272] random: crng init done
[ 8.224188] random: 7 urandom warning(s) missed due to ratelimiting
[ 8.382904] TI DP83867 k3-cpsw-mdio:00: attached PHY driver [TI DP83867] (mii_bus:phy_addr=k3-cpsw-mdio:00, irq=POLL)
[ 8.395415] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.580903] remoteproc remoteproc0: powering up 41000000.r5f
[ 8.586655] remoteproc remoteproc0: Booting fw image am65x-mcu-r5f0_0-fw, size 4050720
[ 8.597588] platform 41000000.r5f: booting R5F core using boot addr = 0x0
[ 8.611221] remoteproc remoteproc0: registered virtio0 (type 7)
[ 8.620442] remoteproc remoteproc0: remote processor 41000000.r5f is now up
[ 8.725647] davinci_mdio b032400.mdio: davinci mdio revision 1.7, bus freq 1000000
[ 8.733378] libphy: b032400.mdio: probed
[ 8.770355] davinci_mdio b032400.mdio: phy[0]: device b032400.mdio:00, driver TI DP83867
[ 8.790056] davinci_mdio b032400.mdio: phy[3]: device b032400.mdio:03, driver TI DP83867
[ 8.866761] davinci_mdio b132400.mdio: davinci mdio revision 1.7, bus freq 1000000
[ 8.874613] libphy: b132400.mdio: probed
[ 8.915020] davinci_mdio b132400.mdio: phy[0]: device b132400.mdio:00, driver TI DP83867
[ 8.929830] davinci_mdio b132400.mdio: phy[3]: device b132400.mdio:03, driver TI DP83867
[ 9.026716] davinci_mdio b232400.mdio: davinci mdio revision 1.7, bus freq 1000000
[ 9.035498] libphy: b232400.mdio: probed
[ 9.067195] davinci_mdio b232400.mdio: phy[0]: device b232400.mdio:00, driver TI DP83867
[ 9.081562] davinci_mdio b232400.mdio: phy[3]: device b232400.mdio:03, driver TI DP83867
[ 9.152264] remoteproc remoteproc1: b034000.pru is available
[ 9.166599] pru-rproc b034000.pru: PRU rproc node pru@b034000 probed successfully
[ 9.193246] remoteproc remoteproc2: b004000.rtu is available
[ 9.204734] pru-rproc b004000.rtu: PRU rproc node rtu@b004000 probed successfully
[ 9.236362] remoteproc remoteproc3: b038000.pru is available
[ 9.266866] pru-rproc b038000.pru: PRU rproc node pru@b038000 probed successfully
[ 9.292350] remoteproc remoteproc4: b006000.rtu is available
[ 9.319238] pru-rproc b006000.rtu: PRU rproc node rtu@b006000 probed successfully
[ 9.335609] remoteproc remoteproc5: b134000.pru is available
[ 9.343924] pru-rproc b134000.pru: PRU rproc node pru@b134000 probed successfully
[ 9.352706] remoteproc remoteproc6: b104000.rtu is available
[ 9.362049] pru-rproc b104000.rtu: PRU rproc node rtu@b104000 probed successfully
[ 9.378779] remoteproc remoteproc7: b138000.pru is available
[ 9.395298] pru-rproc b138000.pru: PRU rproc node pru@b138000 probed successfully
[ 9.404334] remoteproc remoteproc8: b106000.rtu is available
[ 9.411769] am65-cpsw-nuss 46000000.ethernet eth0: Link is Down
[ 9.423262] pru-rproc b106000.rtu: PRU rproc node rtu@b106000 probed successfully
[ 9.437863] remoteproc remoteproc9: b234000.pru is available
[ 9.443963] pru-rproc b234000.pru: PRU rproc node pru@b234000 probed successfully
[ 9.455169] remoteproc remoteproc10: b204000.rtu is available
[ 9.461320] pru-rproc b204000.rtu: PRU rproc node rtu@b204000 probed successfully
[ 9.474375] remoteproc remoteproc11: b238000.pru is available
[ 9.480598] pru-rproc b238000.pru: PRU rproc node pru@b238000 probed successfully
[ 9.494206] remoteproc remoteproc12: b206000.rtu is available
[ 9.504410] pru-rproc b206000.rtu: PRU rproc node rtu@b206000 probed successfully
[ 9.617705] icssg-prueth pruss1_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0
[ OK ] Started Login Service.
[ OK ] Started Reboot and dump vmcore via kexec.
[ OK ] Started rng-tools.service.
[ OK ] Started TI IPC Daemon.
[ OK ] Started RPC Bind Service.
[ OK ] Started Lightning Fast Webserver With Light System Requirements.
[ OK ] Started Permit User Sessions.
[ 9.716944] dwc3 4010000.usb: Failed to get clk 'ref': -2
[ 9.730705] dwc3 4030000.usb: Failed to get clk 'ref': -2
[ 9.737626] icssg-prueth pruss0_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0
[ 9.752709] OF: graph: no port node found in /interconnect@100000/phy@4110000
[ 9.753818] virtio_rpmsg_bus virtio0: rpmsg host is online
[ 9.754704] virtio_rpmsg_bus virtio0: creating channel rpmsg-proto addr 0x3d
[ 9.833118] icssg-prueth pruss2_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0
[ 9.997902] NET: Registered protocol family 15
[ 10.066426] NET: Registered protocol family 45
[ 10.184731] usbcore: registered new interface driver usbfs
[ 10.193421] usbcore: registered new interface driver hub
[ 10.202988] Initializing XFRM netlink socket
[ 10.203215] usbcore: registered new device driver usb
[ 10.227104] icssg-prueth pruss1_eth eth2: flow id base = 150
[ 10.249245] icssg-prueth pruss1_eth eth2: mgm flow id base = 154
[ 10.260356] remoteproc remoteproc7: powering up b138000.pru
[ 10.321438] remoteproc remoteproc7: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 14868
[ 10.331949] remoteproc remoteproc7: remote processor b138000.pru is now up
[ 10.338990] remoteproc remoteproc8: powering up b106000.rtu
[ 10.373121] remoteproc remoteproc8: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15488
[ 10.382314] remoteproc remoteproc8: remote processor b106000.rtu is now up
[ 10.391011] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 10.392978] net eth2: started
[ 10.396562] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 1
[ 10.407569] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 10.407893] xhci-hcd xhci-hcd.2.auto: hcc params 0x0298fe6d hci version 0x110 quirks 0x0000000000010010
[ 10.423083] xhci-hcd xhci-hcd.2.auto: irq 309, io mem 0x04010000
[ 10.429792] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 10.438219] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.445590] usb usb1: Product: xHCI Host Controller
[ 10.450539] usb usb1: Manufacturer: Linux 4.19.38-g4dae378bbe xhci-hcd
[ 10.457351] usb usb1: SerialNumber: xhci-hcd.2.auto
[ 10.463164] hub 1-0:1.0: USB hub found
[ 10.467169] hub 1-0:1.0: 1 port detected
[ 10.471362] icssg-prueth pruss1_eth eth1: flow id base = 157
[ 10.471916] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[ 10.482808] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 2
[ 10.490634] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[ 10.497840] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 10.506396] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[ 10.514822] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 10.522247] usb usb2: Product: xHCI Host Controller
[ 10.527193] usb usb2: Manufacturer: Linux 4.19.38-g4dae378bbe xhci-hcd
[ 10.533898] usb usb2: SerialNumber: xhci-hcd.2.auto
[ 10.539696] hub 2-0:1.0: USB hub found
[ 10.543660] hub 2-0:1.0: 1 port detected
[ 10.549222] icssg-prueth pruss1_eth eth1: mgm flow id base = 161
[ 10.566591] remoteproc remoteproc5: powering up b134000.pru
[ 10.585543] remoteproc remoteproc5: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 14868
[ 10.594685] remoteproc remoteproc5: remote processor b134000.pru is now up
[ 10.602163] remoteproc remoteproc6: powering up b104000.rtu
[ 10.633619] remoteproc remoteproc6: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15488
[ 10.642847] remoteproc remoteproc6: remote processor b104000.rtu is now up
[ 10.651011] net eth1: started
[ 10.654188] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 10.668522] icssg-prueth pruss0_eth eth3: flow id base = 164
[ 10.677985] icssg-prueth pruss0_eth eth3: mgm flow id base = 168
[ 10.686865] remoteproc remoteproc1: powering up b034000.pru
[ 10.692632] remoteproc remoteproc1: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 14868
[ 10.701842] remoteproc remoteproc1: remote processor b034000.pru is now up
[ 10.708860] remoteproc remoteproc2: powering up b004000.rtu
[ 10.714638] remoteproc remoteproc2: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15488
[ 10.723683] remoteproc remoteproc2: remote processor b004000.rtu is now up
[ 10.731678] net eth3: started
[ 10.734911] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
[ 10.747206] icssg-prueth pruss2_eth eth5: flow id base = 171
[ 10.764272] icssg-prueth pruss2_eth eth5: mgm flow id base = 175
[ 10.776753] remoteproc remoteproc9: powering up b234000.pru
[ 10.783068] remoteproc remoteproc9: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 14868
[ 10.792286] remoteproc remoteproc9: remote processor b234000.pru is now up
[ 10.799403] remoteproc remoteproc10: powering up b204000.rtu
[ 10.805346] remoteproc remoteproc10: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15488
[ 10.814580] remoteproc remoteproc10: remote processor b204000.rtu is now up
[ 10.822937] net eth5: started
[ 10.826118] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
[ 10.839018] icssg-prueth pruss2_eth eth6: flow id base = 178
[ 10.848243] icssg-prueth pruss2_eth eth6: mgm flow id base = 182
[ 10.857241] remoteproc remoteproc11: powering up b238000.pru
[ 10.863265] remoteproc remoteproc11: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 14868
[ 10.872423] remoteproc remoteproc11: remote processor b238000.pru is now up
[ 10.879455] remoteproc remoteproc12: powering up b206000.rtu
[ 10.885505] remoteproc remoteproc12: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15488
[ 10.894615] remoteproc remoteproc12: remote processor b206000.rtu is now up
[ 10.902780] net eth6: started
[ 10.905958] IPv6: ADDRCONF(NETDEV_UP): eth6: link is not ready
[ 10.918018] icssg-prueth pruss0_eth eth4: flow id base = 185
[ OK ] Started Serial Getty on ttyS2.
[ 10.929404] icssg-prueth pruss0_eth eth4: mgm flow id base = 189
[ OK ] Started Getty on tty1.
[ 10.941636] remoteproc remoteproc3: powering up b038000.pru
[ OK ] Reached target Login Prompts.
[ 10.948903] remoteproc remoteproc3: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 14868
Starting Synchronize System and HW clocks...
[ 10.961928] remoteproc remoteproc3: remote processor b038000.pru is now up
[ 10.973475] remoteproc remoteproc4: powering up b006000.rtu
[ 10.973817] remoteproc remoteproc4: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15488
[ 10.988148] remoteproc remoteproc4: remote processor b006000.rtu is now up
[ OK [ 10.996266] net eth4: started
] Started NFS status monitor for NFSv2/3 locking..
[ 11.000001] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready
Starting rc.pvr.service...
[FAILED] Failed to start Synchronize System and HW clocks.
See 'systemctl status sync-clocks.service' for details.
[ 11.323073] PVR_K: UM DDK-(4948957) and KM DDK-(4948957) match. [ OK ]
[ OK ] Started rc.pvr.service.
Starting weston.service...
[ OK ] Started weston.service.
Starting Matrix GUI...
Starting telnetd.service...
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ OK ] Started telnetd.service.
Starting thttpd.service...
[ OK ] Started Matrix GUI.
[ OK ] Started thttpd.service.
Starting thermal-zone-init.service...
[ OK ] Started thermal-zone-init.service.
[ OK ] Found device /dev/mmcblk1p1.
Starting File System Check on /dev/mmcblk1p1...
[ OK ] Started Simple Network Management Protocol (SNMP) Daemon..
[ OK ] Started File System Check on /dev/mmcblk1p1.
Mounting /run/media/mmcblk1p1...
[ OK ] Mounted /run/media/mmcblk1p1.
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org am65xx-evm ttyS2
Arago 2019.05 am65xx-evm ttyS2
am65xx-evm login: ***************************************************************
***************************************************************
NOTICE: This file system contains the following GPLv3 packages:
autoconf
bash
bc
binutils
cifs-utils
cpio
cpp-symlinks
cpp
dosfstools
elfutils
g++-symlinks
g++
gawk
gcc-symlinks
gcc
gdb
gdbserver
gettext
glmark2
gstreamer1.0-libav
gzip
hidapi
libbfd
libdw1
libelf1
libgdbm-compat4
libgdbm6
libgettextlib
libgettextsrc
libgmp10
libidn2-0
libmpc3
libmpfr6
libreadline7
libunistring2
m4
make
nettle
parted
pdm-anomaly-detection
which
If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution. This can be done using
the opkg remove command. i.e.:
opkg remove <package>
Where <package> is the name printed in the list above
NOTE: If the package is a dependency of another package you
will be notified of the dependent packages. You should
use the --force-removal-of-dependent-packages option to
also remove the dependent packages as well
***************************************************************
***************************************************************
I checked the markings of the DDR4 memories on the customer's TMDX654IDKEVM and found that the part number was different from the part number in the BOM.
TMDX654IDKEVM BOM: MT40A1G8WE-083E:B
The customer's TMDX654IDKEVM: MT40A1G8SA-062E IT:E
https://www.micron.com/support/tools-and-utilities/fbga?fbga=D9WFP#pnlFBGA
By the way, I checked the markings of the DDR4 memories on own TMDX654GPEVM.
TMDX654GPEVM BOM: MT40A1G8WE-083E:B
Own TMDX654GPEVM: MT40A1G8WE-083E:B
https://www.micron.com/support/tools-and-utilities/fbga?fbga=D9TBH#pnlFBGA
Does DDR4 initialization fail due to the replaced DDR4 memories?
Best regards,
Daisuke
