IWR1642BOOST: Intelligent fall detection using ti mmwave sensors

Abdellah Bouchama

Part Number: IWR1642BOOST
Other Parts Discussed in Thread: IWR1443, IWR6843ISK-ODS

Hello everyone,

I'm trying to reach the lab mentioned here but it seems that it's not reachable.

Could you please indicate for me if there is any older/newer version of this lab with link.

PS : I've already seen the people counting demo and also fall detection lab but if you look very well in the the first lab i mentioned you will notice that it's different (it look for me that it is more accurate) :

Range indication on the ground representation.
No boxes plotted around the point-cloud

Thank you in advance.

Abdellah.

over 3 years ago

+1 Alec May over 3 years ago

TI__Genius 17265 points

Hi,

That experiment can be found at the following link:
https://dev.ti.com/tirex/explore/node?a=VLyFKFf__4.5.1&node=AFmsC4Pjv3N8OtdrcDLsEg__VLyFKFf__4.5.1

Best Regards,
Alec

0 Abdellah Bouchama over 3 years ago in reply to Alec May

Prodigy 160 points

Hi Alec,

Thank you again for your answer it was the exact lab i was looking for.

I'm still having some questions if you can answer please :

I can't access the link for the lab0025 (point cloud) referenced in the lab you mentioned (can you please send me a link for the industrial toolbox containing the lab0025 so that i can get the good firmware)
In the fall detection lab it was mentioned that it is compatible with the IWR6843ISK-ODS, can i run it with the IWR1443 because i think they do have the same configuration?

Thank you Alec so much i really appreciate your help.

Regards.

Abdellah.

+1 Alec May over 3 years ago in reply to Abdellah Bouchama

TI__Genius 17265 points

Hi,

Since this thread has been marked resolved, I will ask that any further questions are asked in a new thread. However, see the following replies

Lab0025: https://dev.ti.com/tirex/explore/node?node=APz8.I6J1HfQwW3H2CVjmA__VLyFKFf__3.6.2

I can not guarantee that this will work on IWR1443 (since the 6843ODS has a different antenna pattern, is a different frequency band, and is lacking a DSP). However, I believe that Lab0025 is just the out of box demo for the ODS board, so you may be able to use the out of box demo for 1443 with the visualizer in that experiment mentioned previously, but since this was not supported, you will need to perform the testing on your own.

Best Regards,
Alec

0 Abdellah Bouchama over 3 years ago in reply to Alec May

Prodigy 160 points

Okey,

Thank you so much Alec for your help. i'm very grateful and appreciate your permanent assistance.

Have a good day.

0 Abdellah Bouchama over 3 years ago in reply to Alec May

Prodigy 160 points

Hello Alec,

I'd ask for one last question please :

The lab you mentioned is a part of the industrial toolbox 3.6.2, the issue is that this version of toolbox is no more accessible. and for my case i need it to get the firmware (.bin) file (or recompile the project) that i should found on :

	`<mmwave_industrial_toolbox_install_dir>\labs\lab0025_ods_point_cloud_demo_68xx\prebuilt_binaries\ods_point_cloud_demo_68xx.bin`

I'm wondering if you have any idea on how to access this version of the industrial toolbox directory, or any link for the firmware download.

Have a good day,

Abdellah.

0 Abdellah Bouchama over 3 years ago in reply to Abdellah Bouchama

Prodigy 160 points

Or how to download the DSS MSS for recompiling it ( i don't have the download button only open on cloud CCS and it does not open the files !!)

+1 Alec May over 3 years ago in reply to Abdellah Bouchama

TI__Genius 17265 points

Hi,

You will need to download the entire toolbox 3.6.2 and import the project locally. You can see instructions on how to do this in the readme in the Industrial Toolbox (in 4.11.0, not sure if the readme existed in 3.6.2)

Best Regards,
Alec

0 Abdellah Bouchama over 3 years ago in reply to Alec May

Prodigy 160 points

Thank you Alec.

Sensors

Sensors forum

IWR1642BOOST: Intelligent fall detection using ti mmwave sensors