• State TI Thinks Resolved
  • Locked Locked
  • Replies 8 replies
  • Answers 1 answer
  • Subscribers 31 subscribers
  • Views 1437 views
  • Users 0 members are here
Support feedback
Options
Options
Related

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

AWR1642BOOST: pplcount

Konstantis Luskin
Intellectual 400 points
Part Number: AWR1642BOOST
Other Parts Discussed in Thread: AWR1642, IWR1642

Hello, I have a few questions about AWR1642.
1. I want to start an example of counting people, it is written for IWR1642, whether it will work for me.
2.When you run the application pplcount_gui.exe, I write an error-dfeDataOutputMode 1
                                                                                                        Warning: Unexpected Warning: A timeout occurred before the Terminator was reached. 
                                                                                                        Warning: Unexpected Warning: A timeout occurred before the Terminator was reached. 
                                                                                                        Warning: Unsuccessful read: The specified amount of data was not returned within the Timeout period..

The remaining configuration commands are also not executed, which may be the reason.

  • 0
    TI__Guru*** 149044 points
    Hi,

    You should be able to run this example on AWR1642 as well.

    The team working on People Counting Application will be able to get back to you after Memorial Day holiday

    thank you
    Cesar
  • 0
    TI__Mastermind 28055 points

    Hi Konstantis,

    1) You can run this on the AWR1642 - follow the same steps you would for the IWR1642.

    2) This error is caused because the Serial port is timing out, probably due to not being connected.  If you have a AWR1642 ES2.0, make sure you are using Industrail Toolbox 2.3.1, otherwise use 2.3.0. ES2.0 will be labeled, ES1.0 is not labeled. Also make sure you are using the GUI to connect to the device.

    Regards,

    Justin

  • 0
    Intellectual 400 points
    Hi Justin,

    I'm sure that I'm doing everything right. I uploaded the debug card in debug and the commands on the COM port began to be accepted and executed. But the GUI application began to crash after pressing the start button at the console writes the following: " Unsuccessful read: The sptcified amount of data was not returned within the Timeout period"  Index exceeds matrix dimension.Error in main_pplcount_viz(line 513).I'm using indastrial_toolbox 2_3_1.


    Вторник, 29 мая 2018, 18:01 +03:00 от Justin Curewitz <bounce-5118664@mail.e2e.ti.com>:

     

    A Message from the TI E2E™ Community
    Texas Instruments

     

    Justin Curewitz replied to AWR1642BOOST: pplcount.

    Hi Konstantis,

    1) You can run this on the AWR1642 - follow the same steps you would for the IWR1642.

    2) This error is caused because the Serial port is timing out, probably due to not being connected.  If you have a AWR1642 ES2.0, make sure you are using Industrail Toolbox 2.3.1, otherwise use 2.3.0. ES2.0 will be labeled, ES1.0 is not labeled. Also make sure you are using the GUI to connect to the device.

    Regards,

    Justin

     
     

    You received this notification because you subscribed to the forum.  To unsubscribe from only this thread, go here.

    Flag this post as spam/abuse.

    refid:5d9437a4-c9e0-4d5b-9f53-6795fa4e5be4


    С уважением,
    Константин Лыскин
    stremitelnu@mail.ru
  • 0
    Intellectual 400 points
    Justin 

    when I press the start button, I see the following in the SCS console:
    Heap before creating a tracker
    System Heap:size 65536,used 50856,free 14680
    (GtrackModuleInstance  0x8008a00)
    System Heap:size 65536,used 50856,free 14680
    MMWDemoMSS Reseived CLI sensorStart Event
    Error:MMWDemo mmWave open configuration failed(Error code -203554190)


    Вторник, 29 мая 2018, 18:01 +03:00 от Justin Curewitz <bounce-5118664@mail.e2e.ti.com>:

     

    A Message from the TI E2E™ Community
    Texas Instruments

     

    Justin Curewitz replied to AWR1642BOOST: pplcount.

    Hi Konstantis,

    1) You can run this on the AWR1642 - follow the same steps you would for the IWR1642.

    2) This error is caused because the Serial port is timing out, probably due to not being connected.  If you have a AWR1642 ES2.0, make sure you are using Industrail Toolbox 2.3.1, otherwise use 2.3.0. ES2.0 will be labeled, ES1.0 is not labeled. Also make sure you are using the GUI to connect to the device.

    Regards,

    Justin

     
     

    You received this notification because you subscribed to the forum.  To unsubscribe from only this thread, go here.

    Flag this post as spam/abuse.

    refid:5d9437a4-c9e0-4d5b-9f53-6795fa4e5be4


    С уважением,
    Константин Лыскин
    stremitelnu@mail.ru
  • 0
    Intellectual 400 points
    Justin

    when I send the command to configure the radar manually, the error about which I wrote above does not arise.


    Вторник, 29 мая 2018, 18:01 +03:00 от Justin Curewitz <bounce-5118664@mail.e2e.ti.com>:

     

    A Message from the TI E2E™ Community
    Texas Instruments

     

    Justin Curewitz replied to AWR1642BOOST: pplcount.

    Hi Konstantis,

    1) You can run this on the AWR1642 - follow the same steps you would for the IWR1642.

    2) This error is caused because the Serial port is timing out, probably due to not being connected.  If you have a AWR1642 ES2.0, make sure you are using Industrail Toolbox 2.3.1, otherwise use 2.3.0. ES2.0 will be labeled, ES1.0 is not labeled. Also make sure you are using the GUI to connect to the device.

    Regards,

    Justin

     
     

    You received this notification because you subscribed to the forum.  To unsubscribe from only this thread, go here.

    Flag this post as spam/abuse.

    refid:5d9437a4-c9e0-4d5b-9f53-6795fa4e5be4


    С уважением,
    Константин Лыскин
    stremitelnu@mail.ru
  • 0 in reply to Konstantis Luskin
    TI__Mastermind 28055 points
    Hi Konstantis,

    I think you may be using the wrong Industrial Toolbox. If your IWR1642 does not say ES2.0 on it, you need to use Industrial ToolBox version 2.3.0.

    Regards,
    Justin
  • 0 in reply to Justin Curewitz
    Prodigy 120 points
    Hello,

    I am running into the same exact problem as described by Konstantis. My board is Rev. A, and it doesn't have the ES2.0 sticker on it. I use the Toolbox version 2.3.0 as suggested, but got the same problem. I have also tried different demo , such as Lab 5 - high accuracy -16xx, and it also stuck in "waiting for data" status. Any suggestion? Is it possible that the board is defective (just received it 3 days ago), but there is no indication that the board's malfunctioned.

    Thanks,
    Yohannes
  • 0 in reply to Yohannes Solichien
    TI__Mastermind 28055 points
    Hi Yohannes,

    Make sure that when running the demo, only SOP2 is connected. Assure that the UART COM port and DATA COM port are properly selected. You should try running the out of box demo. There is a precompiled binary available in the SDK. Find it at <SDK_INSTALL_PATH>\packages\ti\demo\xwr16xx\mmw\

    Regards,
    Justin