TMP112: Difference in the mass production inspection process

user6551657

Prodigy 30 points

Part Number: TMP112

Is there a difference in the mass production inspection process between "TMP112AIDRLR" and "TMP112AQDRLRQ1"?

If there is a difference between the two, please tell me what is the difference.

over 4 years ago

0 Jalen Tate89 over 4 years ago

TI__Genius 9675 points

Hi,

I am checking internally and will follow up once I get more information here.

Jalen

0 Jalen Tate89 over 4 years ago in reply to Jalen Tate89

TI__Genius 9675 points

Hi,

There are a few enhancements in production for our auto qualified sensors in comparison to the commercial products. Standard on all products are a solder reflow and x-ray inspection step during the assembly process. In some cases, there are additional test at probe or final test too. This is all to achieve a low DPPM on automotive products.

Jalen

0 user6551657 over 4 years ago in reply to Jalen Tate89

Prodigy 30 points

Thank you for your comment.

Specifically, please tell me what kind of inspection process is added in "TMP112AQDRLRQ1" compared to "TMP112AIDRLR".

0 Jalen Tate89 over 4 years ago in reply to user6551657

TI__Genius 9675 points

Hi,

I'm working to get more details here. I have to get the feedback from members of our development team. Will update you accordingly.

Jalen

0 Jalen Tate89 over 4 years ago in reply to user6551657

TI__Genius 9675 points

I talked with our development team. More detailed answer below:

All qualification plans for the TMP112-Q1 are in compliance with AEC Q100 and AEC Q006. Those test included on the TMP112-Q1 are:

Final test outlier procedures
Auto visual inspection
Design FMEA
Design for test- this is for temperature fail detection/prevention strategies at hot and cold temps
Design for quality

Jalen

0 user6551657 over 4 years ago in reply to Jalen Tate89

Prodigy 30 points

Thank you for your comment.

I would like to know the difference in the inspection process in the mass production process.

What is the specific difference between "TMP112AIDRLR" and "TMP112AQDRLRQ1"?

Isn't "Design FMEA", "Design for test", and "Design for quality" at the design stage?

Please tell me the difference in the mass production inspection process.

Also, is the design different between "TMP112AIDRLR" and "TMP112AQDRLRQ1"?

I'm sorry I can't understand.

0 Jalen Tate89 over 4 years ago in reply to user6551657

TI__Genius 9675 points

Hi,

For the inspection process in mass production the differences are the final test outlier procedures and auto visual inspection. These test are only implemented on the TMP112AQDRLRQ1.

Jalen

0 user6551657 over 4 years ago in reply to Jalen Tate89

Prodigy 30 points

Thank you for your comment.

What value does "the final test outlier procedures" specifically inspect?

+1 Jalen Tate89 over 4 years ago in reply to user6551657

TI__Genius 9675 points

I'm not sure I can provide specifically what is tested, but this is included to ensure datasheet integrity by meeting the specs in the datasheet.

Jalen

0 user6551657 over 4 years ago in reply to Jalen Tate89

Prodigy 30 points

Thank you for your support.
With the support of the Japanese sales office, the solution was resolved.

The TI E2E™ design support forums will undergo maintenance from July 11 to July 13. If you need design support during this time, open a new support request with our customer support center.

Sensors

Sensors forum

TMP112: Difference in the mass production inspection process