CC1352P7: Big problem programming BeaglePlay with TI XDS110

Tim Cruise

Part Number: CC1352P7
Other Parts Discussed in Thread: UNIFLASH, CC1352P

Dear TI Engineers,

I own a BeaglePlay Board which was planned to become the core border router of my TI Wi-SUN instruments.

https://www.beagleboard.org/boards/beagleplay

Your colleague guided me on how to programme its on board CC1352P7 with XDS110.
https://e2e.ti.com/support/wireless-connectivity/sub-1-ghz-group/sub-1-ghz/f/sub-1-ghz-forum/1343680/how-to-program-and-debug-beagleplay/5123297

However, after I have bought the non-sense TageConnect Cable and its retainer, it turns out that this non-sense cable is incompatible with my TI XDS110 programmer/debugger! Please see the attachments.

Please help me to connect the 2 incompatible sockets. How shall I match the 2 sockets` holes? The only tools I have are breadboard and breadboard flying cables!

over 1 year ago

0 Arthur R☑️ over 1 year ago

TI__Mastermind 25785 points

Hi Tim,

You can follow the method outlined here: https://e2e.ti.com/support/wireless-connectivity/sub-1-ghz-group/sub-1-ghz/f/sub-1-ghz-forum/887212/faq-launchxl-cc1352p-debugger-firmware-upgrade-failure/3281522#3281522

It also uses breadboard flying cables.

Regards,

Arthur

0 Tim Cruise over 1 year ago in reply to Arthur R☑️

Intellectual 978 points

Hello Arthur,

Is this the correct mapping between TagConnect 2050 and XDS110 (yellow box)?

However, when I programmed the BeaglePlay onboard CC1352P7 with CCS or UniFlash, both complained that CC1352P7 could not be reset.

Please advice.

0 Tim Cruise over 1 year ago in reply to Arthur R☑️

Intellectual 978 points

CCS log when I ran verification:

0 Arthur R☑️ over 1 year ago in reply to Tim Cruise

TI__Mastermind 25785 points

Hi Tim,

The pinout I used on the IDC connector is the following, as per your diagram:

1: 3V3 3:GND 5: empty 7: empty 9: empty

2: TMS 4: TCK 6: TDO 8: TDI 10: TDO

Regards,

Arthur

0 Tim Cruise over 1 year ago in reply to Arthur R☑️

Intellectual 978 points

Hello Arthur,

Where is the Reset pin?!?

+1 Arthur R☑️ over 1 year ago in reply to Tim Cruise

TI__Mastermind 25785 points

Hi Tim,

Sorry, the RST pin is actually on pin 10, like so:

1: 3V3 3:GND 5: empty 7: empty 9: empty

2: TMS 4: TCK 6: TDO 8: TDI 10: RST

Regards,

Arthur

0 Tim Cruise over 1 year ago in reply to Arthur R☑️

Intellectual 978 points

Yes, this is the correct pin mapping. I can program the CC1352P now. Thanks.

There are still 2 more questions:

Solved. I also found this on regular CC1352 Launchpad.
On the demo Wi-SUN network monitor dashboard, how do we customise the browser tab title as shown in the white lined box?

+1 Arthur R☑️ over 1 year ago in reply to Tim Cruise

TI__Mastermind 25785 points

Hi Tim,

To change the title, you have to modify line 18 of index.html.

Regards,

Arthur

0 Tim Cruise over 1 year ago in reply to Arthur R☑️

Intellectual 978 points

Yes, it works correctly. Thanks.

Sub-1 GHz

Sub-1 GHz forum

CC1352P7: Big problem programming BeaglePlay with TI XDS110