LAUNCHXL-CC1310: CC1310

Mirko Pribisic

Part Number: LAUNCHXL-CC1310
Other Parts Discussed in Thread: TIDA-01066, CC1310, , SIMPLELINK-CC13X0-SDK, CC1350

I see TI does not have TIDA-01066 evaluation board on sale for low power door / window switch. Can we emulate TIDA-01066 with CC1310 LunchPad boards.

I assume this would be master slave communication.

over 7 years ago

0 YiKai Chen over 7 years ago

Guru 735515 points

Yes, it's designed for LAUNCHXL-CC1310.

0 Mirko Pribisic over 7 years ago in reply to YiKai Chen

Intellectual 280 points

I would like to get 4 lunch pads. One of them I would dedicate as master and get information from the other 3 by periodical request. Power consumption of the master is not an issue but 3 slaves must have very low current draw and run on small battery. At the same time I need to send battery status to master as well.

Is this feasible with lunch pad configuration? Could you point me to some examples?

0 YiKai Chen over 7 years ago in reply to Mirko Pribisic

Guru 735515 points

Yes, it's feasible. You can try collector and sensor examples in TI 15.4 Stack which is included in TI CC13x0 SDK ( you can download it from www.ti.com/.../simplelink-cc13x0-sdk )

0 Mirko Pribisic over 7 years ago in reply to YiKai Chen

Intellectual 280 points

How I can paired collector and sensor nodes ? Is there max. number of sensors to add to network? Is this connection secured - encrypted, rolling code like Microchip KeeyLock or similar?

0 YiKai Chen over 7 years ago in reply to Mirko Pribisic

Guru 735515 points

You have to enable permit join on collector to allow sensor node join. A collector would allow 50 sensor nodes to join when security is enable.

0 Mirko Pribisic over 7 years ago in reply to YiKai Chen

Intellectual 280 points

Does any document exist with detail description of joining collector, security enable and type of security?

0 YiKai Chen over 7 years ago in reply to Mirko Pribisic

Guru 735515 points

If you download and install SIMPLELINK-CC13X0-SDK v1.30, you can refer to ti154stack-software-developers-guide under C:\ti\simplelink_cc13x0_sdk_1_30_00_06\docs\ti154stack

0 Mirko Pribisic over 7 years ago in reply to YiKai Chen

Intellectual 280 points

I try to test Concentrator and Node on my two CC1310 lunch pads with Display but it show error during flashing.
Error connecting to the target:
(Error -241 @ 0x0)
A router subpath could not be accessed.
A security error has probably occurred.
Make sure your device is unlocked.
(Emulation package 6.0.628.1)
Sources: rfWsnDmConcentrator_CC1350_LAUNCHXL_tirtos_ccs & rfWsnDmNode_CC1350_LAUNCHXL_tirtos_ccs
Any idea how to fix this?

0 YiKai Chen over 7 years ago in reply to Mirko Pribisic

Guru 735515 points

Make sure you don't have Flash Programmer 2 and SmartRF Studio opened at the same time. If it still shows error-241, try to restart your windows system and test again.

0 Mirko Pribisic over 7 years ago in reply to YiKai Chen

Intellectual 280 points

I Set up TI wireless network- Sensor & Collector. It works. I monitor nodes connected on Lunch pad with display which is collector. Only one problem I observed: Each time when I powered down one sensor node and powered back again it assign new node address but old one is still on display. Question is: How I can differentiate nodes per their addresses?
Because each ite some node loses power and get back again will have different address so I would not know which of my sensors are off or on wha what data I receive? Any way I can make this differentiation. Ideally I want one sensor - one address assigned forever ?

0 YiKai Chen over 7 years ago in reply to Mirko Pribisic

Guru 735515 points

If you enable NV_RESTORE in your sensor/collector node, the short address shouldn't change everytime you do power cycle.

0 Mirko Pribisic over 7 years ago in reply to YiKai Chen

Intellectual 280 points

Does this mean the sensor node address is saved to data Flash during first time joining the network?

0 YiKai Chen over 7 years ago in reply to Mirko Pribisic

Guru 735515 points

Yes.

Sub-1 GHz

Sub-1 GHz forum

LAUNCHXL-CC1310: CC1310