IAR EW801

Hugo Caldas

Other Parts Discussed in Thread: CC2530, Z-STACK, MSP-FET

Hi,

I want to use the Z-stack Smart Energy on the CC2530's Anaren.

To reprogramme the boosterpack I just need to do it once or every time I run a program?

If I download the Evaluation license of IAR Embedded Workbench (http://supp.iar.com/Download/SW/?item=EW8051-EVAL) , will work?

Best Regards

over 11 years ago

0 YiKai Chen over 11 years ago

Guru 735695 points

It depends! If you use ZAP+ZNP, you only have to program once. Different Z-Stack version uses different IAR version so I suggest you to download matched version from www.iar.com/.../ti-wireless

0 Hugo Caldas over 11 years ago in reply to YiKai Chen

Prodigy 80 points

I will use:
MSP-EXP430G2 - www.ti.com/.../launchpads-msp430-msp-exp430g2.html
CC2530 ANAREN - www.anaren.com/.../cc2530-boosterpack-kit

What else I need to use this evaluation workbench (IAR Embedded Workbench for MSP430) and only program once?

0 YiKai Chen over 11 years ago in reply to Hugo Caldas

Guru 735695 points

I think the CC2530 boosterpack already has ZNP FW on it so you don't even have to flash FW to it. If you really want to do that, you still need CC debugger.

0 Hugo Caldas over 11 years ago in reply to YiKai Chen

Prodigy 80 points

The boosterpack "includes AIR-ZNP firmware solution".
So, I need to buy :
2xMSP-EXP430G2 launchpad
2xCC2530 ANAREN modules
1x CCdebugger
and download v4.21 from IAR Embedded Workbench for MSP430 (www.iar.com/.../ti-wireless)
With this , I just need to re programme once and this evaluation license is enough.
An I right ?

Thank you for reply.

0 YiKai Chen over 11 years ago in reply to Hugo Caldas

Guru 735695 points

If you want to program CC2530, you have to buy CC debugger. However, if you need to program MSP430, you have to buy MSP-FET (http://www.ti.com/tool/msp-fet). Evaluation license is only good for 30 days. If it is enough for you to develop, it is fine.

0 Hugo Caldas over 11 years ago in reply to YiKai Chen

Prodigy 80 points

Can you take a look to the boosterpack please: www.anaren.com/.../cc2530-boosterpack-kit
I want to reprogramme the stack. With a CCdebugger , I don't need to reprogramme just one time?
The evaluation license cannot expire and I continue using the stack already reprogrammed?

I committed a mistake:

"The boosterpack "includes AIR-ZNP firmware solution".
So, I need to buy :
2xMSP-EXP430G2 launchpad
2xCC2530 ANAREN modules
1x CCdebugger
and download version 7.51A or later from IAR Embedded Workbench for 8051 (www.iar.com/.../ti-wireless)
With this , I just need to re programme once and this evaluation license is enough.
An I right ?

Thank you for reply."

Now Am I right?

0 Hugo Caldas over 11 years ago in reply to YiKai Chen

Prodigy 80 points

I committed a mistake in the last message:
"
The boosterpack "includes AIR-ZNP firmware solution".
So, I need to buy :
2xMSP-EXP430G2 launchpad
2xCC2530 ANAREN modules
1x CCdebugger
and download v7.51A from IAR Embedded Workbench for 8051 (www.iar.com/.../ti-wireless)
With this , I just need to re programme once and this evaluation license is enough.
An I right ?

Thank you for reply.
"
With a CC debugger and the IAR workbench, I can reprogramme the Stack.
And when the IAR workbench evaluation license is over, can I continue to use the stack already reprogrammed? That's my question.

0 YiKai Chen over 11 years ago in reply to Hugo Caldas

Guru 735695 points

Yes, you can use the stack already programmed. It doesn't matter with IAR license.

Zigbee & Thread

Zigbee & Thread forum

IAR EW801