How to know endevice join to router or router join to coordinate

user4308805

Other Parts Discussed in Thread: CC2530, Z-STACK

Dear Sir,

I'm use Z-Stack Home 1.2.2.42930 for CC2530, I configured Samplight example for coordinate and SampleSwitch example for router. Router device Joined to Coordinate and it display debug rounter' ShortAddress.

1./ I want know when new device join to coordinate to enable join or disable join to zigbee network. and how to reject this new device?

2./ How to clear network information, that save before?

Thank you,

over 10 years ago

0 YiKai Chen over 10 years ago

Guru 735685 points

Don't understand you question well. What do you mean to know when new device join to coordinate to enable join or disable join to zigbee network?

0 user4308805 over 10 years ago in reply to YiKai Chen

Intellectual 360 points

Yes, are you for me some ideas?

0 user4308805 over 10 years ago in reply to YiKai Chen

Intellectual 360 points

Yes, Please help me

0 YiKai Chen over 10 years ago in reply to user4308805

Guru 735685 points

I would like to help to but i don't understand your question. Can you describe it more clearly?

0 user4308805 over 10 years ago in reply to YiKai Chen

Intellectual 360 points

Dear YK Chen,
My question is how to know a new device request join to a Router or Coordinate.
Thank you,

0 YiKai Chen over 10 years ago in reply to user4308805

Guru 735685 points

When a device joins Zigbee network, it would broadcast end node announcement. You can register for it using ZDO_RegisterForZDOMsg(task_id, Device_annce) in zclXXX_Init and receive Device_annce in zclXXX_ProcessZDOMsgs().

0 user4308805 over 10 years ago in reply to YiKai Chen

Intellectual 360 points

Thank you for you answer, I don't clear. Can you tell me detail on SampLight (coordinate) and SampleSwitch (router) example of Home 1.2.2.42930. The first turn on SampLigh, then turn on SampleSwitch. where SampleLigh code to know SampleSwitch join to Sampleligh to enable, or disable it/

0 YiKai Chen over 10 years ago in reply to user4308805

Guru 735685 points

If your SampleLight is coordinator, you should put my suggested code in it.

0 user4308805 over 10 years ago in reply to YiKai Chen

Intellectual 360 points

Maybe you misunderstand me, I mean how to know MAC (IEEE) of End device to disable join or enable join this device. And function that allows join the network, functions does not allow join the network.
I studied this issue should be more embarrassed, thank you much

0 YiKai Chen over 10 years ago in reply to user4308805

Guru 735685 points

When ZC receives end node announcement, there is short and IEEE address inside it. You can use it to send leave request to ask unwanted end device to leave current Zigbee network.

0 user4308805 over 10 years ago in reply to YiKai Chen

Intellectual 360 points

Dear YK Chen, I tried go to ZDO_RegisterForZDOMsg and command this function . however ED join also to net work. Can you tell me, when start ZC not enable join any device, and only join when a switch is press?

0 YiKai Chen over 10 years ago in reply to user4308805

Guru 735685 points

You can use API NLME_PermitJoiningRequest() to do it. NLME_PermitJoiningRequest(0) means disable permit join to all device and NLME_PermitJoiningRequest(0xFF) means enable permit join.

0 Peter Yin over 10 years ago in reply to user4308805

Expert 1315 points

i think you can see this function: ZDSecMgrDeviceValidateRM, you can implement whitelist or blacklist based your prefer.

if "zgSecurePermitJoin" is false, all device is disable to join,

Zigbee & Thread

Zigbee & Thread forum

How to know endevice join to router or router join to coordinate