CC1310 with Contiki OS

You can refer to sunmaysky.blogspot.tw/.../contiki-subg-hz-6lowpan-on-cc1350.html

Hello, I have already read this guide and I tested. There I understood very little, for if there is something clearer someone else?

Can you elaborate what's unclear?

I tried it with the link you gave me, and gives me an error after that I put: make TARGET = srf06-cc26xx BOARD = srf06 / cc13xx cc26xx-web-demo.bin

I get this error:
fatal error: board. h:No such file or directory #include "board.h"
compilation terminated
make:***[obj_srf06-cc26xx/er-coap.o] Error 1

What is your compile environment? Do you use Cygwin? Or you use Instant Contiki?

Instant Contiki

Do you refer to www.contiki-os.org/start.html

In place of Z1 that I have to put?

I don't understand your question. Can you elaborate?

I opened the link you gave me; in the example it says the device (make TARGET = Z1) instead of z1 should I put the cc1310. How can I do?

I just test to build it with "make TARGET=srf06-cc26xx BOARD=srf06/cc13xx cc26xx-web-demo.bin" on my Instant Contiki and everything works fine. Do you git pull the latest Contiki source code from github?

Do you change directory to \contiki\examples\cc26xx\cc26xx-web-demo when you build cc26xx-web-demo?

I've changed everything. But I have always the same error. Ie fatal error board.h Contiki-conf.h: 330: 19

Ok I loaded the cc26xx-web-demo.bin. Now I have to do?

You have to setup 6lbr to make CC1310 running cc26xx-web-demo to join.

How?

You can refer to sunmaysky.blogspot.tw/.../setup-6lbr-to-run-6lowpan-with-cc2531.html

It wants to force a raspberry?

What do you mean "It wants to force a raspberry?"

In the guide that you sent me you say connection via USB to your Raspberry Pi 2B. So to set the 6lbr I need a Raspberry?

You can run 6lbr on Raspberry Pi, BeagleBone, or any Linux OS. The processes are similar. You can refer to github.com/.../Other-Linux-Software-Configuration

I followed this your link but after a while they give me error. The alternative is to use the raspberry?

Can you elaborate your problem?

In the first part where I want to start off on the border router he tells me permission denied.
1) Could not open lock file / var / lib / dpkg / lock

Do you try to switch to root and do again?

Come you switch to root mode?

Ok he went. On the second point when I put the link to download the package tells me ERROR 404 not found. I can go on, or is some mistake?

Can you elaborate what step you do to see Error 404 not found?

--2016-11-10 10:19:04-- raw.github.com/.../cetic-6lbr_1.4.0_armhf.deb
Resolving raw.github.com (raw.github.com)... 151.101.60.133
Connecting to raw.github.com (raw.github.com)|151.101.60.133|:443... connected.
HTTP request sent, awaiting response... 301 Moved Permanently
Location: raw.githubusercontent.com/.../cetic-6lbr_1.4.0_armhf.deb [following]
--2016-11-10 10:19:05-- raw.githubusercontent.com/.../cetic-6lbr_1.4.0_armhf.deb
Resolving raw.githubusercontent.com (raw.githubusercontent.com)... 151.101.16.133
Connecting to raw.githubusercontent.com (raw.githubusercontent.com)|151.101.16.133|:443... connected.
HTTP request sent, awaiting response... 404 Not Found
2016-11-10 10:19:05 ERROR 404: Not Found.

user@instant-contiki:~$

I don't know what you are doing. Can you elaborate where you refer to do this?

Try to run Installation from sources instead of Binary package installation.

user@instant-contiki:~$ cd 6lbr
user@instant-contiki:~/6lbr$ git submodule update --init --recursive
user@instant-contiki:~/6lbr$ cd examples/6lbr
user@instant-contiki:~/6lbr/examples/6lbr$ git checkout develop-xxxxx #optional
error: pathspec 'develop-xxxxx' did not match any file(s) known to git.
user@instant-contiki:~/6lbr/examples/6lbr$

I think you can skip the following two steps:


git submodule update --init --recursive
git checkout develop-xxxxx #optional, if you plan to use a develop snapshot</pre>

Ok, I get this error:

user@instant-contiki:~/6lbr/examples/6lbr$ make all #all_native for version < 1.4
rm -rf bin
mkdir -p bin
make TARGET=native clean
make[1]: Entering directory `/home/user/6lbr/examples/6lbr'
rm -f *~ *core core *.srec \
*.lst *.map \
*.cprg *.bin *.data contiki*.a *.firmware core-labels.S *.ihex *.ini \
*.ce *.co
rm -rf *.so obj_native/*.so
rm -rf obj_native
make[1]: Leaving directory `/home/user/6lbr/examples/6lbr'
make TARGET=native bin/cetic_6lbr_smart_bridge
make[1]: Entering directory `/home/user/6lbr/examples/6lbr'
make TARGET=native CETIC_6LBR_SMARTBRIDGE=1 WITH_UDPCLIENT=0
make[2]: Entering directory `/home/user/6lbr/examples/6lbr'
make[2]: Nothing to be done for `cetic-6lbr'.
make[2]: Leaving directory `/home/user/6lbr/examples/6lbr'
mkdir -p bin
mv cetic-6lbr.native bin/cetic_6lbr_smart_bridge
mv: cannot stat ‘cetic-6lbr.native’: No such file or directory
make[1]: *** [bin/cetic_6lbr_smart_bridge] Error 1
make[1]: Leaving directory `/home/user/6lbr/examples/6lbr'
make: *** [all] Error 2
user@instant-contiki:~/6lbr/examples/6lbr$

I suggest you to setup another Linux VM instead of instant Contiki to build 6lbr or buy a raspberry Pi to do it.

I'll try the raspberry. Do you have any guidance? Ah, I wanted to ask you something. How can I install the operating system on the CC1310? Through examples? Thanks for your kindness

Do you use CC1310 LaunchPad?

Yes

There is XDS110 debugger embedded on CC1310 LaunchPad so you can use Flash Programmer to download FW to it.

I've got a raspberry. If you give me a guide where to have each record linking .. I hope to move forward

You can refer to steps in sunmaysky.blogspot.tw/.../setup-6lbr-to-run-6lowpan-with-cc2531.html

Ok thanks now I follow this guide. But you do feel some connection between the smartRF06 and Raspberry?

What do you mean "feel some connection between the smartRF06 and Raspberry?"

In the guide you've passed me, there are types of applications such as:

SSH login to Raspberry Pi. How do I proceed with this step?

try to refer to pimylifeup.com/.../