RTOS/LAUNCHXL-CC2650: Error "section placement failure"

Frederic Griffe

Part Number: LAUNCHXL-CC2650
Other Parts Discussed in Thread: CC2650, Z-STACK

Tool/software: TI-RTOS

Hello

I am following the CC2650 LaunchPad User's Guide for ZigBee (http://processors.wiki.ti.com/index.php/CC2650_LaunchPad_User's_Guide_for_ZigBee?keyMatch=CC2650%20launchpad%20zigbee&tisearch=Search-EN-Everything

using IAR ARM 8.20.1

When I try to "build All" on "ZstackCore" have the following message :

Error[Lp015]: section placement failure: overcommitted content in [0x0000d000-0x0001cfff]

Any solution ?

over 8 years ago

0 JasonB over 8 years ago

TI__Expert 8950 points

Hi,

Do you have optimization disabled for the ZStackCore project?

0 Frederic Griffe over 8 years ago in reply to JasonB

Expert 1745 points

Hi,

No, optimization is set to high (size)

Frederic

0 Frederic Griffe over 8 years ago in reply to Frederic Griffe

Expert 1745 points

Hi,

I went to Linker Optimization and selected Inline small routines, Merge duplicate sections and Perform C++ Virtual function elimination (but not "even if some... )
And it worked !

Thanks a lot.

Frederic

0 Luu Van Luc over 8 years ago in reply to Frederic Griffe

Prodigy 170 points

Hi,

I am a beginer and I have a same problem. I want to say thank you so much.

And I have a question. I have 2 CC2650LP. It seem that TI just support CC2650 for BLE. And have you finished your Zigbee CC2650 project yet? Have you had any problem with this project.

Sorry my bad English.

Thanks a lot.

Luc

0 Frederic Griffe over 8 years ago in reply to Luu Van Luc

Expert 1745 points

Hello,

I finally decided to go for Bluetooth for the first version of my product.

I will tackle ZigBee at a later stage. I have the same feeling that Ti does not fully support ZigBee (or less than bluetooth).

Kind regards.

Frederic

0 Luu Van Luc over 8 years ago in reply to Frederic Griffe

Prodigy 170 points

Hi,
I have no choice. I have to use Zigbee for my project.
Anyway, thanks you so much,
Best regards,
Luc

0 YiKai Chen over 8 years ago in reply to Luu Van Luc

Guru 735695 points

There is new CC2652 that new Z-Stack can support all ZC, ZR, and ZED configurations. It will be more suitable than CC2650 if you want to develop Zigbee application using CC26xx.

0 Luu Van Luc over 8 years ago in reply to YiKai Chen

Prodigy 170 points

This seem to be a new product from TI.
And I can not find any guide for this product.

0 YiKai Chen over 8 years ago in reply to Luu Van Luc

Guru 735695 points

You can refer to www.ti.com/.../LAUNCHXL-CC26X2R1

0 Luu Van Luc over 8 years ago in reply to YiKai Chen

Prodigy 170 points

Thanks you a lot

0 Luu Van Luc over 8 years ago in reply to Frederic Griffe

Prodigy 170 points

Hi,
I built all and downloaded this project. It is OK, but I had a problem with Zigbee CC2650LP. This application didn't work.
I have a question. You did this project with Zigbee CC2650LP, right. And did it work?
Thanks in advance,
Luc

0 Frederic Griffe over 8 years ago in reply to YiKai Chen

Expert 1745 points

Thanks a lot for the information.

Do you know if the SIMPLELINK-CC26X2-SDK and the SIMPLELINK-ZIGBEE-SDK-PLUGIN V0.95 will run on CCS (as opposed to IAR).

Kind regards.

0 YiKai Chen over 8 years ago in reply to Luu Van Luc

Guru 735695 points

I have some projects using CC2650 running Zigbee end device with Z-Stack Home 1.2.2a without problem. And, Yes, SIMPLELINK-CC26X2-SDK and the SIMPLELINK-ZIGBEE-SDK-PLUGIN V0.95 runs on CCS

0 Luu Van Luc over 8 years ago in reply to YiKai Chen

Prodigy 170 points

Thank you. I know how it didn't work. CC2650 just support for End Device, not Router and Coordinator.
Now I try using Contiki with 6LowPan for CC2650. 6LowPan base on IEEE802.15.4 Standard, so I think it is great.
Do you have any recommenation for me?
Thanks,
Luc

0 YiKai Chen over 8 years ago in reply to Luu Van Luc

Guru 735695 points

Contiki is great but it is open source. It needs you to put a lot of effort to study it and make it work.

0 Luu Van Luc over 8 years ago in reply to YiKai Chen

Prodigy 170 points

Thank you a lot. I try

Zigbee & Thread

Zigbee & Thread forum

RTOS/LAUNCHXL-CC2650: Error "section placement failure"