CC2530: Power conserve problem in end device!

Piaozhun

Expert 2620 points

Part Number: CC2530
Other Parts Discussed in Thread: Z-STACK,

Hi everyone.

I have release smart system with coordinator and end device(use Battery) but they have many issues.

I have some problems are as following:

1. After coordinator is power off and power on , end device can't rejoin to coordinator soon.

2. In 1) , power conserve in end device is high.

I want to lowest power conserve of end device with coordinator's status and coordinator communication with sleeping end device anytime.

Please help me.

Thanks in advance.

Piao

over 7 years ago

0 YiKai Chen over 7 years ago in reply to Piaozhun

Guru 735685 points

When you use Ubiqua Analyzer to open sniffer_log5.psd, you need to select "Zigbee" and "Version 2.17.0 or later"

0 Piaozhun over 7 years ago in reply to YiKai Chen

Expert 2620 points

Yes, I did so.

Then I am using trial version of ubiqua.

is this issue?

0 YiKai Chen over 7 years ago in reply to Piaozhun

Guru 735685 points

I don’t think so.

0 Piaozhun over 7 years ago in reply to YiKai Chen

Expert 2620 points

Hi YiKai Chen Sir.

Sorry disturb to you.

I did put option of project as follwoing.
SECURE=1
TC_LINKKEY_JOIN
NV_INIT
NV_RESTORE
POWER_SAVING
NWK_AUTO_POLL
ZTOOL_P1
xMT_TASK
xMT_APP_FUNC
xMT_SYS_FUNC
xMT_ZDO_FUNC
xMT_ZDO_MGMT
xMT_APP_CNF_FUNC
xLEGACY_LCD_DEBUG
xLCD_SUPPORTED=DEBUG
MULTICAST_ENABLED=FALSE
ZCL_READ
xZCL_WRITE
xZCL_BASIC
ZCL_IDENTIFY
xZCL_SCENES
xZCL_GROUPS
HAL_PA_LNA

I still don't packet to coord.

I can't understnad for this issue.

Please help me.

Piao

0 Piaozhun over 7 years ago in reply to Piaozhun

Expert 2620 points

Hi YK Chen Sir.

I have one question.
I did set "SECURE = 1", How to see "ABCDE" in sniffer log file?

Piao

0 Piaozhun over 7 years ago in reply to YiKai Chen

Expert 2620 points

Hi YK Chen Sir.

I have one question.
I did set "SECURE = 1", How to see "ABCDE" in sniffer log file?

Thanks in advance.

Piao

0 Piaozhun over 7 years ago in reply to YiKai Chen

Expert 2620 points

Hi YK Chen Sir.

I have set "SECURE = 0" and test .

But I have got any packet from coordinator.

I attached sniffer log file.

If you have free time,Please check my sniffer file.

sniffer_log6.psd

Sorry for disturb to you.

Best regards.

Piao

0 YiKai Chen over 7 years ago in reply to Piaozhun

Guru 735685 points

I see your device been left by coordinator in sniffer_log6 so it might be security problem again. Do you add ZigBee Alliance Pre-configured TC Link Key - 'ZigBeeAlliance09' into keychain of Ubiqua Security Options. If not, you have to add it and open sniffer_log5.psd again.

0 Piaozhun over 7 years ago in reply to YiKai Chen

Expert 2620 points

Hi YK Chen Sir.

Thanks for your fully advise.

Piao

Zigbee & Thread

Zigbee & Thread forum

CC2530: Power conserve problem in end device!