Frequent Questions

  • [FAQ] AM625: How to configure Timer in Interrupt mode

    Part Number: AM625 Other Parts Discussed in Thread: SYSCONFIG Lets have a look at the implementation of application using a TIMER module(DM TIMER) in Interupt mode of operation. The application code can be used as it is or as a baseline for configuring…

  • [FAQ] AM62D-Q1 Custom board hardware design – AUDIO-AM62D-EVM Audio Functionality Implementation Related Queries and Design Notes

    Part Number: AM62D-Q1 Other Parts Discussed in Thread: AUDIO-AM62D-EVM Hi TI experts, I am planning to reuse the AM62D-Q1 AUDIO-AM62D-EVM schematics for my custom board design. I see the below schematic sections (pages) added to the AUDIO-AM62D-EVM…

  • [FAQ] TDA4VH-Q1: How to configure the SerDes lane for PCIe, USB, Ethernet, and Display in Linux?

    Part Number: TDA4VH-Q1 The high speed interfaces on the TDA4x share the SerDes lanes. The lanes can be muxed for different interfaces, but how can I configure them within Linux?

  • [FAQ] AM2754-Q1: Working Configurations for 8S-8S-8S on S28HS512T Serial NOR OSPI Flash

    Part Number: AM2754-Q1 Other Parts Discussed in Thread: SYSCONFIG In the MCU+ SDK 11.02 offering, the examples of OSPI and Flash are configured to work at the highest protocol that is 8D-8D-8D. In case for profiling purpose, an engineer wants to run…

  • [FAQ] TDA4VH-Q1: How to reset C7x and load binary faster via CCS

    Part Number: TDA4VH-Q1 Hi, After reset of C7x, i am trying to load newer C7x binary, but the second load takes a lot of time. Could you please help me to solve this issue.

  • [FAQ] AM64/AM243: Facing an issue with CCS when trying to flash an image using SBL JTAG UNIFLASH

    Part Number: AM6442 Other Parts Discussed in Thread: UNIFLASH I am trying to flash an image for AM64/AM243 device by loading SBL JTAG UNIFLASH from CCS version 20. *.* , after following the steps mentioned in the MCU+SDK documentation: https://software…

  • [FAQ] BQ25630EVM: .BQZ file for BQ25630 Evaluation Module

    Part Number: BQ25630EVM Other Parts Discussed in Thread: BQ25630 , BQSTUDIO , Please see attached for the BQ25630 BQZ file to be used with BQSTUDIO software. To use the GUI you will need to download Battery management studio software from TI.com,…

  • [FAQ] printf demo for MSPM0 device

    Other Parts Discussed in Thread: LP-MSPM0G3507 printf_to_uart_LP_MSPM0G3507_nortos_ticlang.zip Default UART pin is PA10 and PA11, and it's based on LP-MSPM0G3507 default. Please check corresponding Launchpad's User guide schematic before test. There…

  • [FAQ] TVS2210: TVS2210 Device Part Marking

    Part Number: TVS2210 The device I received is marked as 'TV' but that is not listed as an option in the datasheet.

  • [FAQ] BQ2518xEVM: Where is the .bqz file? Can the EVM be used with the EV2400 and bqStudio?

    Part Number: BQ25188EVM Other Parts Discussed in Thread: BQSTUDIO , EV2400 , BQ25188 , BQ25186 , BQ21088 The BQ2518x EVM can be used with the EV2400 and bqStudio. Connect the SDA, SCL, and GND pins on the EVM to the corresponding pins on the EV2400…

View FAQ threads