Search tips
Showing 21 results View by: Thread Post Sort by

  • adc08060

    Other Parts Discussed in Thread: ADC08060 I use the ADC08060 for my data switch, use the typical circle, even I force the input to VDD or GND ,There is no output datas,not so much changes from the output. Please Tell me why?

  • Increase ADC08060 Analog Bandwidth?

    Other Parts Discussed in Thread: ADC08060 I would like to know more about what limits the ADC08060 ADC's analog bandwidth. Most converters have an analog bandwidth much greater than their sample rate - but not so with the ADC08060. Can I increase the…
    • Answered

  • How does performance of the ADC08060 degrade as the clock is increased beyond 60MHz? The data sheet implies that it operates at least at 70MHz, although it's fully specified only up to 60MHz. Does the ENOB degrade gracefully with increased clock rate

    Resolved
    Other Parts Discussed in Thread: ADC08060 , ADC08100 Could I run for example at 100MHz? 150MHz? Is there perhaps a graph of ENOB vs clock rate? Or does the ADC08060 fail catastrophically beyond 60MHz?
    • Resolved

  • ADC08L060: Clock input voltage/sensitivity for VDR=1.8V?

    TI Thinks Resolved
    Part Number: ADC08L060 Other Parts Discussed in Thread: ADC08060 Tool/software: I plan to interface with a 1.8V FPGA for the 8-bit digital output (VDR=1.8V and VA=3.3V). However, it is not clear if the device can accept a 1.8V input on the clock. Table…
    • Answered

  • ADC08L060: Driving voltages at 1.8V allowed?

    Resolved
    Part Number: ADC08L060 Other Parts Discussed in Thread: ADC08060 , I'd like to use the ADC08L060 and communicate with a 1.8V MCU ideally without level shifters. In the opening description of this part unlike the ADC08060 it says "The digital outputs are…
    • Resolved
    • Answered

  • RE: ADC08100EVM: Schematic and PCB Layout for Eval Module

    Resolved
    Hi David, You can find the design files on the ADC08060 product page in the design & development section. Here is the link: https://www.ti.com/product/ADC08060#design-development . Regards, David Chaparro
    • Answered

  • RE: ADC1173: ADC 8 bit 15Msps parallel int for Induction Motor EE

    Resolved
    Hi Fax The best fit for that need is probably the ADC08060. It is active and the recently updated ADC08060EVM is available for customer evaluation. While the ADC1173 is only rated for -40 to +75 C operation the ADC08060 is rated from -40 to +85C. Best…

  • ADC3244: Using ADC3244 together with STM32F411RET for LIDAR application

    TI Thinks Resolved
    Part Number: ADC3244 Other Parts Discussed in Thread: ADC3643 , ADC3664 , ADS801 , ADC08060 , ADC10065 Hi Team, Our customer will use ADC3244 together with STM32F411RET for LIDAR application. According to the customer, We think that we need to…

  • mid range high speed A/D converters single ended clock tree solutions

    TI Thinks Resolved
    Other Parts Discussed in Thread: ADC08060 , ADS831 Hello What are the solutions for clocking multiple (e.g 4) A/D converters like ads831 or adc08060 with/out phase shift? Thanks.

  • RE: ADC08060EVM: Digital output value won't change

    Hi Toby, Initially, I would leave JP8 and JP9 in their default condition (1-2) since these set the fullscale input range of the ADC. Are you applying an AC or DC signal at the analog input (VIN) in order to change the output codes? This EVM was designed…

Didn't find what you are looking for? Post a new question.