TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 11 results View by: Thread Post Sort by
    Answered
  • ADC101C021: How to working on fSCL = 3.4MHz?

    Andy Lin
    Andy Lin
    Resolved
    Part Number: ADC101C021 Tool/software: Dear TI team: About ADC101C021 If I want to working on fSCL = 3.4MHz, do I need to set up something? (ex:fIN?) And if necessary, how to set it? Thanks~ Best Regards, Andy
    • Resolved
    • 4 months ago
    • Data converters
    • Data converters forum
  • Answered
  • ADC101C021: Pull-up resistor voltage

    cafain
    cafain
    Resolved
    Part Number: ADC101C021 Tool/software: Hi, Staff When the VA of the ADC101C021 is 3.3V, is it possible to use the Alert pin with the pull-up resistor voltage pulled up to 5V? In this case, is it okay to set the pull-up resistance value so that it does…
    • Resolved
    • 8 months ago
    • Data converters
    • Data converters forum
  • Answered
  • ADC101C021: ALERT pull up voltage

    Hirotsugu Kobayashi
    Hirotsugu Kobayashi
    Resolved
    Part Number: ADC101C021 Tool/software: Hi team, Is it possible to pull up the ALERT terminal to a voltage higher than VA? I am considering VA=3.3V, pull-up voltage=5V.
    • Resolved
    • 8 months ago
    • Data converters
    • Data converters forum
  • Answered
  • ADC101C021: is pinout right?

    murat turgut
    murat turgut
    Resolved
    Part Number: ADC101C021 I am trying to use adc101c021 at my board. on the datasheet, pin id 1 is Va and this pin showed as voltage in. pin id 3 is Vin and this pin showed as analog in put. however when I connect power supply (3.3 volt) to the…
    • Resolved
    • over 2 years ago
    • Data converters
    • Data converters forum
  • ADC101C021: Vin voltage Drop

    Anthony Yoo68
    Anthony Yoo68
    TI Thinks Resolved
    Part Number: ADC101C021 Hello My customer designed the key input circuit with adc101c021 as the attached figure. However, with the "Steering_key" line open, the Vin voltage is dropped to about 0.8V. Does this adc not use Vin port in a pull-up configuration…
    • over 6 years ago
    • Data converters
    • Data converters forum
  • Answered
  • RE: ADS1015: PGA

    Joseph Wu
    Joseph Wu
    Resolved
    Moez, I'm not very familiar with the ADC101C021. However, this device does appear to support the HS-mode I2C communication. Because it doesn't list the I2C general call, I would guess that the device does not respond to that reserved address. …
    • over 5 years ago
    • Data converters
    • Data converters forum
  • Answered
  • RE: 10 bit SAR ADC supporting more than 10 I2C slave address?

    Keith Nicholas
    Keith Nicholas
    Resolved
    Hello Hisao-san, The only devices that I could find that support more than 10 I2C addresses are the ADS1119 (16b) and ADS1219 (24b). Either of these devices will support up to 16 I2C addresses. The ADC101C021 is a 10b converter and supports up to…
    • over 5 years ago
    • Data converters
    • Data converters forum
  • Answered
  • RE: INA220 / measure the AC current

    Jason Bridgmon
    Jason Bridgmon
    Resolved
    Ryuji Asaka, This INA199A1 and ADC101C021 solution seems reasonable. I read up on the ADC101C021 and I see that it requires a stable Va because the power supply is also the reference to the device. In addition to that, the I2C bus is supposed to be…
    • over 11 years ago
    • Amplifiers
    • Amplifiers forum
  • ADC121C021 holds SDA line low

    nigel gordon
    nigel gordon
    TI Thinks Resolved
    Other Parts Discussed in Thread: ADC101C021 , ADC081C021 , ADC121C021 , USB2ANY , ADC121C021EVM When ADDR0 or ADDDR1 is floating in order to sit at one of the tri level addresses it eventually holds SDA low if continually reading the ADC register. Reading…
    • over 9 years ago
    • Data converters
    • Data converters forum
  • Answered
  • RE: AMC1200: Have trouble with two reference designs

    Damith Pavithra
    Damith Pavithra
    Resolved
    It is in the 19th page of this pdf under the title "2.2.3 Isolated Voltage Measurement Using AMC1200" I plan to use the charger for the High side power. tiduby7a.pdf
    • over 6 years ago
    • Amplifiers
    • Amplifiers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question