Search tips
Showing 10 results View by: Thread Post Sort by

  • ADC34J43: What is the default values of registers after RESET?

    TI Thinks Resolved
    Part Number: ADC34J43 Hi experts, The datasheet says the device should be hardware reset to its default values after power up. However the datasheet does not introduce what is the default values after reset. How can I get this information? Thank you…
    • Answered

  • RE: ADC34J43: Data converters forum

    Resolved
    Thanks. I tried the GUI tool for the EVM. And finally figure out that PLatinum isn't 'smart' enough to get solutions I need, I must manually change some settings to get correct frequency output.
    • Answered

  • RE: ADC34J43: SYSREFP, SYSREFM, SYNCP~, SYNCM~ interface to LVDS

    Resolved
    Thanks for your help. I'll try that. Actually, I have tried to find a chip can translate standard LVDS to SLVDS, but with no luck.

  • ADC34J43: JESD204

    TI Thinks Resolved
    Part Number: ADC34J43 Other Parts Discussed in Thread: ADC3443 Hello, In the ADC34J43 version, there is a digital gain option to set the FS swing between 1Vptp and 2Vptp with the registers at the addresses 02h to 05h. If I'm selecting 1Vptp (digital…
    • Answered

  • ADC34J43EVM: SPI communication to the ADC34J43 EVM

    Resolved
    Part Number: ADC34J43EVM Other Parts Discussed in Thread: ADC34J43 Hello, A question please, about the SPI communication to the ADC34J43 EVM: I wish to configure the ADC from an external FPGA, assembled on a different board. I saw that there is…
    • Resolved
    • Answered

  • LMK04832: Termination about LCPECL

    Resolved
    Part Number: LMK04832 Other Parts Discussed in Thread: ADC34J43 , ADC34J43EVM I'm designning a board based on lmk04832 and adc34j43, taking ADC34J43EVM as reference. And I feel the termination schema is like a black box, especially for LCPECL output.…
    • Resolved

  • ADC3443: FS

    TI Thinks Resolved
    Part Number: ADC3443 Other Parts Discussed in Thread: ADC34J43 , Hello Can I use the registers of the digital gain (addresses 02h to 05h from the ADC34J43) for the ADC3443 (no JESD version) if I want to change the FS between 1 Vptp and 2Vptp ? and how…
    • Answered

  • RE: ADC34J42EVM: Need ADC34J42 EVM with configuration file having 50 MSPS sampling rate.

    Resolved
    Hi Dan, For replies marked in bold underlined to the following queries below I still have doubts. 2) By specifications of ADC 34J42 EVM it's maximum Sampling rate is 50 MSPS according to Introduction part in page 3 in the user guide in the following…

  • RE: Seeking advice to digitize 256+ outputs on .5mm- pitch at 40MSPS+ with 14bit+ SNR on Imager Chips.

    Hi Mike, Without reading into too much of the details, have you taken a look at the ADC34J43? Quad channel 14-bit in a small 7x7mm package. Very low power, so thermal design shouldn't be an issue with such high density. The JESD204B output interface is…

  • RE: TSW1400EVM: TSW1400EVM, ADC3423

    slau579d.pdf Leejh, Connect a 80Msps clock (or lower) to SMA J9 with a power of at least 10dBm. See section 1.4 and figure 7 of the attached ADC3423EVM User's Guide. Regards, Jim

Didn't find what you are looking for? Post a new question.