• 

  Steve Sutherland

  • 5 months ago
  • Data converters
  • Data converters forum

  ADS8344: timing related noise

  Part Number: ADS8344 I am reading 4 channels at a time from the ADS8344EBG4 in 24-bit mode, with no power-down between cycles, using an external clock ( 1.5 MHz ) In this mode I send ( 13 * 8 ) clocks to the device, with nCS framing all of the clocks...
• 

  Akhilesh K

  • 1 month ago
  • Data converters
  • Data converters forum

  RE: DAC8554: Linux driver for DAC8554

  Hi, Sorry to say, we don't have any Linux driver for DAC devices. I cant comment on the ADS8344 device. Regards, AK
• 

  KELVIN.LEE

  • 6 months ago
  • Data converters
  • Data converters forum

  ADS8344EVM: How to config Power Supplies Settings and Pins on ADS8344 EVM ?

  • Resolved

  Part Number: ADS8344EVM Hello I'm trying to connect ADS8344 EVM with ATMEGA128. But I'm not sure
• 

  Randhir Kalsi

  • over 1 year ago
  • Data converters
  • Data converters forum

  ADS8344: Is datasheet packaging information correct?

  • Resolved

  Part Number: ADS8344 Hello team, Hope you are doing. Have a customer who is requesting
• 

  user5264061

  • over 2 years ago
  • Data converters
  • Data converters forum

  RE: ADS8344: I use the ADS8344, and the input connect with a Operational amplifier . The Operational amplifier design as a voltage follow. But the ADC value read by ADS8344 Is wrong. If the ADS8344 input don't connect with Operational ampifier, the...

  Thanks for your reply, I add a 0.1uf cap to the ADS8344's ADC input, and the value of ADC is accurate.
• 

  Cynthia

  • over 3 years ago
  • Data converters
  • Data converters forum

  RE: ADS8344: Avoid floating signals on unused analog inputs

  Hello Andrew, If certain channels are not being used on the ADS8344 , then through the digital communicaiotns, they can not be converted. You can use the Control Byte, shown in table 3 of the datasheet , to be sure that the unused channel is not sampled...
• 

  Don Schelle

  • over 3 years ago
  • Data converters
  • Data converters forum

  ADS8344: SPI Protocol Question

  Part Number: ADS8344 Hello, I'm debugging a problem and need a little help understanding the ADS8344 SPI bus. Figure 4 (page 13 of the datasheet), indicates two things: DCLK must be low during the falling edge of the chip-select (CS#) event...
• 

  Art Kay

  • over 3 years ago
  • Data converters
  • Data converters forum

  RE: ADS8344: Reach Certificate for ADS8344NB

  Andrea, You can download the reach or RoHS compliance directly from the TI.com. The attachment below shows how. Thanks, How to Find Reach and RoHS forms on TI.pptx
• 

  farzin dinyarian

  • over 4 years ago
  • Data converters
  • Data converters forum

  ADS8344 16-Bit, 8-Channel Serial Output Sampling Analog-to-Digital Converter

  TI Thinks Resolved

  Hello, I am using Atmel SAME70Q21 MCU SPI interface to write into ADS8344, I have the following questions that I was wondering if you could please help me. 1) Do you have any code samples for this configuration? Atmel SAME70+ADS8344? 2) Should I...
• 

  stephen postlethwaite

  • over 3 years ago
  • Data converters
  • Data converters forum

  ADS8344: Lockup after esd spike

  Part Number: ADS8344 Hi, a customer has reported a strange issue with the ADS8344 after the product has been subjected to an ESD spike. he's what happens 1: Initially, ADC working normally 2: ESD spike applied to products external analogue...

Didn't find what you are looking for? Post a new question.

• Ask a new question