Search tips
Showing 58 results View by: Thread Post Sort by
    Answered

  • ALM2402F-Q1: ALM2402F-Q1

    Resolved
    Part Number: ALM2402F-Q1 Other Parts Discussed in Thread: ALM2403-Q1 Tool/software: Hello, i'm using the ALM2402F-Q1 to amplify a 0-3V signal at 29kHz to get a 8V signal to a 50ohm load. To this purpose i performed a simulation with Tina using TI device…
    • Resolved

  • ALM2402F-Q1: X-ray inspection

    TI Thinks Resolved
    Part Number: ALM2402F-Q1 Hi team, The customer is using ALM2402FQPWPRQ1. Does this device have any requirements for X-RAY radiation dose or X-RAY irradiation voltage and current parameters? If so, please provide relevant data. Best Regards, Jade…
    • Answered

  • ALM2402F-Q1: Saturation in simulation

    Resolved
    Part Number: ALM2402F-Q1 Other Parts Discussed in Thread: ALM2403-Q1 Tool/software: Hi, I'm using ALM2402F-Q1 for automotive application and Vs set to 12V. During simulation op-amp is saturating at 11V although ALM2402F-Q1 is rail-to-rail op-amp. However…
    • Resolved

  • ALM2402F-Q1: PPAP20250220-038454

    TI Thinks Resolved
    Part Number: ALM2402F-Q1 Tool/software: Hello good morning TI team, could you please provide status about the PPAP : Automotive PPAP request: PPAP20250220-038454 Thanks in advance, Kevin W.

  • ALM2402F-Q1: How to set current limit external of ALM2402F-Q1?

    Part Number: ALM2402F-Q1 Tool/software: Hi Team, Can you please help advise how to configure external current limit by Alm2402? The datasheet said by set up Rlim, but where is this resistor Rlim being placed? Do we have reference if customer required…
    • Answered

  • ALM2402F-Q1: Op amp Second Channel Unused pins floating/ terminated to gnd or configured as unity gain and not connected to load

    Resolved
    Part Number: ALM2402F-Q1 I am using the ALM2402F-Q1 , but I am only using one channel of the opamp. How do I connect the pins that correspond to the second channel? Can I leave the pins IN(2)+, IN(2)-, OUT(2) and VS O(2) floating ? Or would that cause…
    • Resolved
    • Answered

  • ALM2402F-Q1: Switching frequency and decoupling capacitor

    Resolved
    Part Number: ALM2402F-Q1 Other Parts Discussed in Thread: TIDM-02014 , ALM2403-Q1 Tool/software: Hello, TI expert. Our resolver drive circuit consists of RC filter and general-purpose op-amps. When I study TIDM-02014, I am attracted by the protection…
    • Resolved

  • ALM2402F-Q1: Inquiry on Cemc Capacitor Selection and Phase Margin

    TI Thinks Resolved
    Part Number: ALM2402F-Q1 Other Parts Discussed in Thread: ALM2402-Q1 , Tool/software: Hi TI team, We are using one of your component ALM2402FQPWPRQ1 in our product, which drives excitation signals to a vehicle motor. Upon reviewing the datasheet, we…

  • ALM2402F-Q1: ALM2402

    Part Number: ALM2402F-Q1 Other Parts Discussed in Thread: ALM2402-Q1 , Hi, Can i use ALM2402 instead of a Darlington transistor for current amplify? In my old circuit there are 2N6301 and 2N6299 for current amplifing, can i change these transistors…

  • ALM2402F-Q1: Comparison between ALM2402-Q1 and ALM2402F-Q1

    Part Number: ALM2402F-Q1 Other Parts Discussed in Thread: ALM2402-Q1 , Hi team, Due to supply shortage, customer is looking for a replacement solution of ALM2402-Q1. Could you please help provide a comparison table between ALM2402F-Q1 and ALM2402-Q1…

Didn't find what you are looking for? Post a new question.