Search tips
Showing 76 results View by: Thread Post Sort by

  • AMC1300: Power supply requirment

    TI Thinks Resolved
    Part Number: AMC1300 Hii I want to use the AMC1300 iso-opamp for one of my application. I have seen the datasheet that in section 7.8 safety limit value supply current required is 0.266A or 0.406A. Can I know what it means. Do the primary power supply...

  • RE: AMC1300: Isolation Amplifiers

    Hi Alex, Thanks for the clarification. Regards Manoj.R

  • AMC1300: Magnetic Field Affection

    TI Thinks Resolved
    Part Number: AMC1300 Hi Team, I have question about the magnetic field affection of AMC1300. We can see too much error. The error is over the expectation which are like shunt resistor variant, temperature affection etc... Do you know any reasons...

  • AMC1300: AMC1300 has Single Protection in UL1577

    • Resolved
    Part Number: AMC1300 Hi all Would you mind if we ask UL1577? AMC1300 has Single Protection

  • AMC1300: Minimum distance between two AMC1300

    • Resolved
    Part Number: AMC1300 hi, we are designing voltage (4 ch) and current (4 ch) sense board using

  • RE: AMC1300: Noise reduction in AMC1300

    Hi Rajasekaran, You may want to consider adding a differential cap between OUTH and OUTL after the resistor to form a differential RC filter, but that is all I can suggest. If you have specific questions about the AMC1300 I am happy to help.

  • AMC1300: Parallel operation of the AMC1300 for current measurement.

    Part Number: AMC1300 Dear sir, we are trying to measure the current (4 ch) & voltage (4 ch) using AMC1300. All channels are connected in parallel. All the 8 qty of AMC1300 high side are supplied by 5V source PS1. All the 8 qty of AMC1300 low...

  • AMC1300: Design Support Request

    • Resolved
    Part Number: AMC1300 Hello, Could you please support my customer? 1. He didn't observe expected

  • RE: AMC1100: Single Ended Output

    Hi Akash, yes, with the help of a differential amplifier as shown in figure 52 of datasheet of AMC1300: Kai

  • AMC1300: AMC1300 Filter

    Part Number: AMC1300 HI Sir I use the AMC1300 for current monitor,shunt is 0.01 ohm I can see the amc1300 output 0.02A when no current flow below figure is my circuit,do you have any suggestion for filter design before the AMC1300? Thanks

Didn't find what you are looking for? Post a new question.


All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI worldwide | Contact us | myTI login | Corporate citizenship

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2020 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy policy | Terms of use