Search tips
Showing 18 results View by: Thread Post Sort by
    Answered

  • AMC1350-Q1: AMC1350-Q1 output value

    Resolved
    Part Number: AMC1350-Q1 Tool/software: Hi According to simulation ,I'm getting required differential output voltage 1.2V. But my doubt is ,if we consider separate output voltage OUTP and OUTN (as per graph shown below) it is sine wave starting from…
    • Resolved

  • AMC1350-Q1: Footprint not clear, also need alternative component

    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 , AMC3330 Hi, I have recently created a design using the AMC1350QDWVRQ1. On the component datasheet and therefore on numerous comparison/supplier websites the component is listed as having…

  • AMC1350-Q1: Driving SAR ADC 16bits/1MSps with the AMC1350

    TI Thinks Resolved
    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 , THS4551 , ADS8411 Hi, I am trying to drive an SAR ADC with the AMC1350 without success. The ADC ref is AD4005 (16-Bit, 2 MSPS/1 MSPS, Precision, Differential SAR ADCs). The observed measured…
    • Answered

  • AMC1350-Q1: OUTN Direct input to MCU

    Resolved
    Part Number: AMC1350-Q1 Hi team, I have a question. When we want to connect OUTN to MCU directly, should we pull up this line with 10kOhm to VDD2? Best regards, Shoji
    • Resolved

  • AMC1350-Q1: Needed design support for high accurate low error input attenuation stage for this amplifier

    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 I am looking for a technical support where the solution should matches with the requirements of my design. To give you my design heads-up, I am using TI’s Precision Reinforced Isolation…
    • Answered

  • AMC1350-Q1: AMC1350 output RC filter and stability

    Resolved
    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 , , TINA-TI Hello, I am planning to connect a RC filter on the output of AMC1350. The spec says that if R=0 the max. "OUTP to OUTN" cap is 250pF. How can I determined the maximum capacitor…
    • Resolved

  • AMC1350-Q1: RCR filter a mandatory

    TI Thinks Resolved
    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 , INA149 , ISO224 I am using AMC1350 to meaure 3-phase voltages. The differential signal is converted to single ended further and scaled to connect to an ADC. In this thread discussed, u discussed…
    • Answered

  • AMC1350-Q1: Can AMC1350 sample negative voltage?

    Resolved
    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 Hi Expert, Q1:Can AMC1350 sample negative voltage.For example,INN connect to GND1,INP is -3V. From above typical application,we can see when INP-INN is -5V,the absolute voltage of INP is…
    • Resolved

  • AMC1350-Q1: three phase Ac voltage sensing

    TI Thinks Resolved
    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 , AMC1200 AMC1350_sim_no_diff.TSC 1. The above circuit is used in AC voltage sensing. The output is finally fed to the controller. Please do share review comments and precautions to be taken…
    • Answered

  • AMC1350-Q1: DC voltage measurement with resistive divider

    Resolved
    Part Number: AMC1350-Q1 Other Parts Discussed in Thread: AMC1350 , AMC3330 , ISO224 , AMC1351 Hi, I'm trying to perform a DC voltage measurement with the AMC1350, but I'm having some difficulties: I have a resistive divider to measure a DC voltage…
    • Resolved

Didn't find what you are looking for? Post a new question.