TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文

Filter by Reset

All
Forums (856)
  • Power management (846)
  • Amplifiers (2)
  • Interface (2)
  • Sensors (2)
  • MSP low-power microcontr... (1)
  • Code Composer Studio™︎ (1)
  • Arm-based microcontrolle... (1)
  • Simulation, hardware & system... (1)
  • View all
Technical Articles (0)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To
Please correct dates.


Search tips
Showing 856 results View by: Thread Post Sort by
  • RE: BQ40Z50: Looking for Battery monitoring and protection system for Non rechargeable 4x AA alkaline batteries in series

    Onyx Ahiakwo
    Onyx Ahiakwo
    Bhupendar, No the bq40z50 will not work for you. it is designed for secondary cells and there is no gauge in the market that will by pass a bad cell if a fault is detected with one of them. Alkaline batteries are non-rechargeable cells so if you are…
    • over 8 years ago
    • Power management
    • Power management forum
  • BQ78Z100: Device Type between two bq78z100 ICs does not match - why?

    Mark Pearson
    Mark Pearson
    TI Thinks Resolved
    Part Number: BQ78Z100 Other Parts Discussed in Thread: BQ34Z100 , BQ35100 , BQSTUDIO My customer has been having issues in communicating with the bq78z100 on his board: The two bytes for device type on the EVM are the third and fourth byte of the response…
    • over 6 years ago
    • Power management
    • Power management forum
  • Answered
  • LM66100: Reverse polarity protection with TVS diode and polyswitch

    Stefano Infante
    Stefano Infante
    Resolved
    Part Number: LM66100 Other Parts Discussed in Thread: BQ35100 , ESDS312 , ESDS314 , ESDS302 , ESD351 , TPS62840 Hello, I am designing a new battery powered circuit and I need some protections on the battery connection. The battery will be a 3.6V primary…
    • Resolved
    • over 5 years ago
    • Power management
    • Power management forum
  • Answered
  • RE: BQ34Z100-G1: Reading Multiple Data with I2C

    Bryan Kahler
    Bryan Kahler
    Resolved
    Hi Kipton, If the data is located next to each other, they could be read at the same time with a block read. Extended commands are read similarly to standard commands. The fastest way to dump data from the bq34z100-g1 while executing firmware is…
    • over 6 years ago
    • Power management
    • Power management forum
  • Answered
  • RE: BQ35100EVM-795: Unable to set EOS mode via bqStudio Advanced Comm

    Rob Fetchin
    Rob Fetchin
    Resolved
    I found a solution. Batt's comment about the checksum caused me to reread 11.17 MACDataSum(): 0x60 and 11.18 MACDataLen(): 0x61 in the Technical Reference Manual . Here's the key line: "Subcommands that require block data are not executed until MACDataSum…
    • over 6 years ago
    • Power management
    • Power management forum
  • RE: BQ35100EVM-795: Interface connection from PC USB - EV2300 - bq35100evm-795 board

    answer
    answer
    Hi I have successfully to connect the bq35100 evm with ev2400 and win7 64bit system. please check you hardware settings: make sure to connnect a battery of power supply to the BAT+ and BAT- connector of bq35100 evm (for example 3V) try to use…
    • over 8 years ago
    • Power management
    • Power management forum
  • RE: Part suggestion

    Haidar Hamoo
    Haidar Hamoo
    Hi Rolan, Thank you for considering TI devices in your design, please check our primary lithium battery fuel gauge and battery end-of-service monitor bq35100, additionally, we had some of our customers successfully used bq34z100-G1 in their primary…
    • over 8 years ago
    • Power management
    • Power management forum
  • UCC12050EVM-022: 13 Ways To Contact How can i talk to someone at Price-line®︎: A Step By Step Guide

    Peter Look
    Peter Look
    TI Thinks Resolved
    Part Number: UCC12050EVM-022 Tool/software: To contact a live representative at Priceline ®, call their 24/7 customer service hotline at +1-8-1-5-3-7-3-1-9-9-5 or 1-800- Priceline ®. You can also use their website's live chat or email for assistance.…
    • 2 months ago
    • Amplifiers
    • Amplifiers forum
  • UCC12040: 13 Ways To Contact How can i talk to someone at Travelo-city®︎: A Step By Step Guide

    Peter Look
    Peter Look
    TI Thinks Resolved
    Part Number: UCC12040 Tool/software: To contact a live representative at Travelocity ® , call their 24/7 customer service hotline at +1-8-1-5-3-7-3-1-9-9-5 or 1-800- Travelocity ® . You can also use their website's live chat or email for assistance. Whether…
    • 2 months ago
    • Power management
    • Power management forum
  • RE: BQ27750EVM-837: integrate into application for monitoring

    Vos
    Vos
    Anja, Connecting the device to just monitor voltage and current is easy. When you say you want to monitor relative state of charge this is where the learning and configuration is needed. Relative State of charge is a complicated thing. It is very dependent…
    • over 7 years ago
    • Power management
    • Power management forum
<
« 79 80 81 82 83 »
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question