• 

  Joseph Borrelli

  • 10 months ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1108: Power up timing of this device

  Part Number: CDCLVC1108 I need to know how long it takes the CDCLVC1108 to reach normal operating mode from the application of valid +3.3Vdc power?
• 

  Frank Xiao

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1108: 12 channel 25M clk buffer

  TI Thinks Resolved

  Part Number: CDCLVC1108 Hi team, My customer is looking for 12channel clk buffer, the input is 3.3v TTL 25Mhz, the output is LVDS or HCSL. The line length is 50cm. Do you have some suggestions? Thanks.
• 

  Michael T Schneider

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1108: handle input clock signals without Main 3.3 V power applied

  • Resolved

  Part Number: CDCLVC1108 quick question. Can this part can handle input clock signals without Main
• 

  AnBer

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

  RE: CDCLVC1108: Additional thermal data?

  Hi Lane, If a complete model is not available could you please provide the "Operating junction temperature" and "Theta_JC_bot" ? "Operating junction temperature" is the " Recommended Continuous Operating Junction Temperature"...
• 

  Ohad Fundoianu

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1108: No maximum values for input voltages are mentions in Recommended operating conditions

  TI Thinks Resolved

  Part Number: CDCLVC1108 Hi, I donot understand these details in that datashhet of CDCLVC1102-12 : 1. There is no max value for High Level Input voltage (see *1) 2. What is Vth and why do the units of Vth and Vih are in mv ? (see *2)
• 

  Kai Hsiao

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1108: I2S Clock buffer

  TI Thinks Resolved

  Part Number: CDCLVC1108 HI Sir Do we have any solution could be used for I2S application or CDCLVC1108 can be used Our request is 1 to 8 (due to I2S have 3 signal ,so if have 3 to 24 ,it will be better) Thanks
• 

  NObody

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1108: this device can use low freq. and

  Part Number: CDCLVC1108 Sorry to bother, as the title, if customer want to use this device to fan out 120Hz clock, is it ok?? Anther questions, I saw "TI recommends placing the series resistor close to the driver to minimize signal reflection...
• 

  Mark Guastaferro

  • over 3 years ago
  • Clock & timing
  • Clock & timing forum

  CDCLVC1108 output termination advice

  TI Thinks Resolved

  Using the CDCLVC1108 to drive 8 output clocks to similar devices. F = 40 MHz. VDD = 3.3V, but receiving devices require clock signal between 1VPP and 2VPP. Trace length is about 100mm (50 ohm). Looking for a low power method to terminate CDCLC1108 outputs...
• 

  Burak b

  • over 4 years ago
  • Logic
  • Logic forum

  TXB0106PWR output problem

  Hello, I am using TXB0106PWR level translator in my circuit and i have a problem about translating to 5V from 3.3 V; I use TXB0106PWR in my circuit as below: I drive input port A (3.3 V) , but I can not get 5V at the outputs (B); when I look...
• 

  Lane Boyd

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

  RE: CDCV304: Do we have General purpose 1:8 clock buffer (8 outputs)

  Hi Shai, I recommend the CDCLVC1108. Kind regards, Lane

Didn't find what you are looking for? Post a new question.

• Ask a new question