• CDCLVP111-SP: Question about Thermal Information change in the datasheet

  

  Kazuhiko Hirano

  TI Thinks Resolved

  Part Number: CDCLVP111-SP Tool/software: Hello, Thermal Information was updated at datasheet rev.B from rev.A. Has thermal resistance changed in actual device manufacturing? Or did TI correct the thermal resistance in the RevA Datasheet because the…

  • 22 days ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVP111-SP: Input/Dynamic Capacitance

  

  anonymouse

  Resolved

  Part Number: CDCLVP111-SP Tool/software: Hello, Do we know if there is an input capacitance (Ci) and dynamic capacitance (Cpd) available for the part CDCLVP111-SP? Thank you.

  • Resolved

  • 4 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVP111-SP: Is CDCLVP111-SP input cold spareable?

  

  user463911

  Resolved

  Part Number: CDCLVP111-SP Tool/software: With CDCLVP111-SP un-powered, is the input cold spareable? In this cold-sparing condition, signal integrity does not matter. Please inform whether CDCLVP111-SP input can be driven indefinitely with the drive level…

  • Resolved

  • 8 months ago
  • Clock & timing
  • Clock & timing forum

• RE: CDCLVP111-SP: delay

  

  Michael Srinivasan

  Hi Pascal, I have completed the calculations to find that the CDCLVP111-SP has a maximum tpd shift of 0.767 ps/°C, and an average shift of 0.123 ps/°C. Thanks, Michael

  • 5 months ago
  • Clock & timing
  • Clock & timing forum

• CDCLVP111-SP: Question about Vod(min) spec

  

  Kazuhiko Hirano

  TI Thinks Resolved

  Part Number: CDCLVP111-SP Other Parts Discussed in Thread: CDCLVP111 Tool/software: Hello, CDCLVP111-SP datasheet specifies differential Vod(min) = 350mV. However, CDCLVP111 datasheet specifies differential Vod(min) = 600mV. Why the differential Vod…

  • 9 months ago
  • Clock & timing
  • Clock & timing forum

• CDCLVP111-SP: question about Vdo spec

  

  Kazuhiko Hirano

  TI Thinks Resolved

  Part Number: CDCLVP111-SP Tool/software: Hello, I have a question about the Vdo spec in the datasheet below. From common sense, the differential output voltage swing Vdo definition should be as follows. However, looking at the following E2E thread…

  • 8 months ago
  • Clock & timing
  • Clock & timing forum

• CDCLVP111-SP: Rthjunction_case(bottom)

  

  pascal lassave

  TI Thinks Resolved

  Part Number: CDCLVP111-SP Tool/software: Hi TI Team below is the answer TI sent last fiiday relative to Rth junction case (bottom): (email from Anass Mrabett, TI, France) So we read 34°C/W for Rthjunction case (bottome) while detailed spec (smd…

  • 9 months ago
  • Clock & timing
  • Clock & timing forum

• CDCLVP111-SP: CDCLVP111-SP vs MVFREP radiation tolerances

  

  JUAN MARTINEZ MILLAN

  TI Thinks Resolved

  Part Number: CDCLVP111-SP Tool/software: Does anyone know the difference between a CDCLVP111MVFREP and the CDCLVP111-SP in terms of radiation? would like to know if we can use the same radiation for TID-DD-SEE for the VFEP as for the -SP. thanks in advance…

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVP111-SP: power dissipation in the CDCLVP and in the loads

  

  pascal lassave

  Resolved

  Part Number: CDCLVP111-SP Other Parts Discussed in Thread: CDCLVP111 Tool/software: On the CDCLVP111 SP, can you confirm the output and internal current supply current is 405mA with all outputs (10) terminated to 50 Ohm ? This current value takes into…

  • Resolved

  • 8 months ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCLVP111-SP: Power dissipation at 100MHz x 6

  

  Kazuhiko Hirano

  Resolved

  Part Number: CDCLVP111-SP Hello, My customer plans to use CDCLVP111-SP to distribute 6x 100MHz differential LVPECL output. In this case how much the device internal power dissipation would be at maximum? Best regards, K.Hirano

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.