Answered

• CDCM61002: About LVDS to LVDS Connection

  

  Shiberu Oyama

  Resolved

  Part Number: CDCM61002 In the Data sheet LVDS Termination section,they say "If the supply voltage of the driver and the receiver are different, ac-coupling is required." Why is AC coupling required for LVDS-to-LVDS connections when the driver…

  • Resolved

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

• CDCM61002 Junction temperature

  

  Yadong Duan

  TI Thinks Resolved

  Part Number: CDCM61002RHBR Hi Team, Would you please provide the CDCM61002RHBR the Junction temperature? customer want to thermal simulation. Many thank

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

• CDCM61002: unstable frequency output

  

  Elian Samaan

  Part Number: CDCM61002 Other Parts Discussed in Thread: OMAP-L138 I am using 25MHz quartz crystal and strapped the chip configuration to output 100MHz CLK. The chip works as expected for a while but the issue seems to occur most if I recycle power to the…

  • over 5 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCM61002: Phase Noise at 125MHz and Crystal Power

  

  Howard Anderson

  Resolved

  Part Number: CDCM61002 We are considering use of the CDCM61002 Clock Generator in our design. I have two questions that I hope you can quickly help me with: 1) The LVDS phase noise numbers in the datasheet (page 5) are at 625 MHz. Can you get me phase…

  • Resolved

  • over 5 years ago
  • Clock & timing
  • Clock & timing forum

• CDCM61002: Configuration question

  

  Andrey Ampelonov

  TI Thinks Resolved

  Part Number: CDCM61002 Hello. Is OSC_OUT in this chip really turned off then outputs configured in to LVCMOS mode or not?

  • over 6 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCM61002: CDCM61001

  

  Shyama S

  Resolved

  Part Number: CDCM61002 Hi sir, In CDCM61002 if one clock output is not used can i leave the corresponding two pins open? Will that affect the IC functionality? If it is not to be left open how to engage the two pins(pulled high/pulled low)? Regards, …

  • Resolved

  • over 6 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCM61002: Temperature drift

  

  FRA51029

  Resolved

  Part Number: CDCM61002 Other Parts Discussed in Thread: CDCM61004 , , CDCM9102 Hello, The CDCM61004 has a temperature drift limitation of 100°C (indicated in datasheet since revision H January 2016). The CDCM61002 which is a similar device (but with…

  • Resolved

  • over 7 years ago
  • Clock & timing
  • Clock & timing forum

• TDA4VE-Q1: Heterogenous multiprocessor design - clock generator synchronisation

  

  jars121

  TI Thinks Resolved

  Part Number: TDA4VE-Q1 Other Parts Discussed in Thread: AM2434 , CDCM61002 , CDCM61001 , LMK3H0102 Hi TI, I'm working on a design which requires industrial ethernet (Profinet, EtherCAT, etc.) and real-time processing capabilities, in addition to higher level…

  • over 1 year ago
  • Processors
  • Processors forum

• about CDCM61002 hardware setting

  

  Nat Wong

  Other Parts Discussed in Thread: CDCM61002 Dear Sirs The attachment is my design: But there no signal at clock out. Could you help me to check? CDCM61002.pdf BRS Nat

  • over 9 years ago
  • Clock & timing
  • Clock & timing forum
Answered

• CDCM61002/CDCM61004

  

  itabi

  Resolved

  Hi I have some questions. We will need 3 output of LVCMOS. 1. Is it possible to stop the clock of specific out pin? 2. How to deal with unused out pin (pull-up, pull-down, open) ? Best regards itabi

  • Resolved

  • over 10 years ago
  • Clock & timing
  • Clock & timing forum

Didn't find what you are looking for? Post a new question.