Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.
Part Number: CDCM6208 Hello,
Which are the differences between CDCE6208V1 and CDCM6208V1F?
On the other hand, is it necessary to sypply the not used outputs? Is it necessary to add external components in not used outputs?
About the power supply for VCO…
Part Number: CDCM6208V1F Other Parts Discussed in Thread: TICSPRO-SW , , LMK03318
Hi Team,
Is following setting possible when using TICSPRO-SW to configure CDCM6208V1FRGZR?
IN : 50MHz(PRI_REF or SEC_REF) OUT : all of outputs is 322.265625 MHz(LVDS)
Beat…
Part Number: CDCM6208V1F Hi team,
When they read the register value of CDCM6208V1HRGZR on their board, the regsiter is 0x0102. BIT 8 is "1", though it should be ignored according to the datasheet, but is it OK to read "1" as BIT 8? …
Part Number: CDCM6208V1F Other Parts Discussed in Thread: CDCM6208V1 , CDCM6208 Hi Team,
CDCM6208V1/2 fVCO is (V1| 2.39~2.55GHz) and (V2|2.94~3.13GHz).
if we send wrong divider setting and then make CDCM6208V1/2 fVCO out of range, how CDCM6208V1/V2 behaves…
Part Number: CDCM6208V1F Other Parts Discussed in Thread: CDCM6208V1 Hi Team,
Can we re-use CDCM6208V1 crystal design to CDCM6208V2 crystal design?
Crystal design is matched to CDCM6208V1 and PCB. When we just replace CDCM6208V1 with CDCM6208V2, i'd like…
Part Number: CDCM6208V1F What is the difference between them, if any?
We designed with CDCM6208V1RGZT. Is the CDCM6208V1FRGZT a drop-in replacement?
What is the meaning of the "pin mode variant F"?
Thanks in advance.
Part Number: CDCM6208V1F Other Parts Discussed in Thread: CDCM6208 Hello,
I am using CDCM6208V1HRGZR part number (above its mentioned as F as it did not accept the H one).
My configurations are-
1. DVDD and VDD_Yx. All supplies connected to 3V3, including…
Part Number: CDCM6208V1F
Hi all Would you mind if we ask CDCM6208V1F? Our customer will use CDCM6208V1F with Y0 and Y6 only. And the customer would like to reduce power consumption. <Question1> Is it possible to power off VDD_Y2_Y3, VDD_Y4, VDD_Y5, …
Part Number: CDCM6208V1F Other Parts Discussed in Thread: CDCM6208 I have a CDCM6208 configured to produce 100MHz on Y0 (LVDS) and 500MHz on Y6 (LVDS). The 100MHz is working, but there is no evidence that the 500MHz is. I suspect it is not, because it…
Part Number: CDCM6208V1F I want get 1.8v-LVCMOS and 3.3v-LVCMOS at the same time .I wander if i give 1.8v to DVDD,then i give 1.8v and 3.3v to different VDD_Yx_Yy. Does this setting can realize?
or the DVDD MUST ≥ VDD_Yx_Yy？
