TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 24 results View by: Thread Post Sort by
  • DAC904: DAC904 CLK Pin requirements

    Qiang Ren
    Qiang Ren
    TI Thinks Resolved
    Part Number: DAC904 Team, We want to check with you about the DAC904’s CLK input design requirements. If we use 122.88Mhz LVPECL’s single end as input, is that okay? Thanks Qiang
    • over 1 year ago
    • Data converters
    • Data converters forum
  • Answered
  • DAC904: The choose of I/V opa of DAC904

    Hanlin Wei
    Hanlin Wei
    Resolved
    Part Number: DAC904 Other Parts Discussed in Thread: OPA891 Tool/software: In my system, the DAC904 output 50kHz~100kHz square wave to control Photo Phase Modulator. The I/V opa using so far is tow-stages OPA891, power supplying ±5V. I am not sure…
    • Resolved
    • 9 months ago
    • Data converters
    • Data converters forum
  • DAC904: output current when just power-up

    Chi Zhang2
    Chi Zhang2
    TI Thinks Resolved
    Part Number: DAC904 Hi Expert, my customer is using DAC904E in fixed network, there is one question needing your help. when power up the power supply rail, VA to 3.3V, VD to 5V. other pin is floating or not connected. we find the output current will…
    • over 2 years ago
    • Data converters
    • Data converters forum
  • Answered
  • DAC904: Power-down characteristics

    Jejomar Ildefonso
    Jejomar Ildefonso
    Resolved
    Part Number: DAC904 Hi Team, Can you give us more information on the output states of DAC904 when it enters power-down mode? The datasheet unfortunately lacks further characterizations. Asking this as our customer has the DAC with an amplifier set-up…
    • Resolved
    • over 4 years ago
    • Data converters
    • Data converters forum
  • Answered
  • DAC904: 25Ohm Impedance Match configuration in datasheet

    Harson
    Harson
    Resolved
    Part Number: DAC904 Hi, Team My customer is designing DAC904, they have a question about the datasheet Page 11( figure 4). It is designed to be a 25Ohm symmetric load at IOUT & ~IOUT. From ~IOUT terminal it's 26.1Ohm//(402+200Ohm), from IOUT Terminal…
    • Resolved
    • over 5 years ago
    • Data converters
    • Data converters forum
  • DAC904: DAC904 OK with 3.3V +VD, 5.0V +VA? performance?

    Eric Smith2
    Eric Smith2
    Part Number: DAC904 Other Parts Discussed in Thread: THS5671A Using the DAC904 with 3.3V +VD and 5.0V +VA doesn't exceed the absolute maximum ratings (+VA to +VD in range -6V to +6V), but will doing so result in satisfactory operation, i.e., performance…
    • over 8 years ago
    • Data converters
    • Data converters forum
  • Answered
  • DAC904: power-up sequence

    K.Yaita
    K.Yaita
    Resolved
    Part Number: DAC904 Hi Team, My customer considers to use DAC904 with VA=5V, VD=3.3V. Is there recommended power-up sequence between supplying VA and VD? Best Regards, Yaita
    • Resolved
    • over 6 years ago
    • Data converters
    • Data converters forum
  • DAC904: E

    YIFEI ZHAO
    YIFEI ZHAO
    Part Number: DAC904 Hi, I am using DAC904E to generate signal for active noise cancellation. A Xillinx Spartan 6 FPGA is interfaced to DAC904E. The DAC904E is configured the same as the "TYPICAL CONNECTION CIRCUIT" on page 4 of the datasheet. A low…
    • over 7 years ago
    • Data converters
    • Data converters forum
  • DAC904: high DC voltage generation

    Vijay bansal
    Vijay bansal
    Part Number: DAC904 Other Parts Discussed in Thread: DAC5682Z I want to generate a high DC voltage of 10 volt with power supply of 24 volt. i want to use this DAC to generate the voltage . can you suggest amplifier which can be used after the DAC904…
    • over 8 years ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • Output Status of DAC904 during power down.

    Osamu Uchino
    Osamu Uchino
    Resolved
    Other Parts Discussed in Thread: DAC904 We are going to use DAC904 in a new project. I have a question about the output of this DAC904 at the time of the power down. During power down, what kind of state is the output  ? Is it high impedance ? if device…
    • Resolved
    • over 10 years ago
    • Data converters
    • Data converters forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question