TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Enterprise Automation Integration
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 45 results View by: Thread Post Sort by
    Answered
  • DP83848M: PFB PIN connection

    Shunsuke Yamamoto
    Shunsuke Yamamoto
    Resolved
    Part Number: DP83848M Hi teams, On the datasheet of DP83848M, Connecting to PIN 19 (PFBOUT), PIN16 (PFBIN1) and PIN30 (PFBIN2) is recommended. On the other hand, on the figure 19 of EN55011, these pins are not shorted. Which one is correct? Best regards…
    • Resolved
    • 6 months ago
    • Interface
    • Interface forum
  • RE: AM5718: DP83848M 10Base-T on autonego

    jian35385
    jian35385
    Toshio, is there anyway you can test the the following: 1. test if eth0 works with the 100Base-T hub in half-duplex mode 2. read the actual status of the MDIO register on the PHY to understand what mode the PHY is in. The ethtool report may not be correct…
    • 6 months ago
    • Processors
    • Processors forum
  • Answered
  • DP83848M: Replacing with DP83848J

    Jejomar Ildefonso
    Jejomar Ildefonso
    Resolved
    Part Number: DP83848M Other Parts Discussed in Thread: DP83848J , Hi Team, Our customer is currently using DP83848M but they don't use the CLK_OUT pin 21. For procurement reasons would it possible for them to use the J version (DP83848J) instead of the…
    • Resolved
    • 8 months ago
    • Interface
    • Interface forum
  • DP83848M: Design Review Support needed for DP83848MPHPEP

    chethan md
    chethan md
    Part Number: DP83848M Hi I am using the part DP83848MPHPEP in my design and need the design review support. The config I am using the device is in RMII mode. Attaching the schematics. Thanks. Eth_tranceiver_DP83848MPHPEP_review_TI.pdf
    • 10 months ago
    • Interface
    • Interface forum
  • DP83848M: Using the DP83848MPHPEP in RMII mode, and need the Evaluation board schematic in RMII configuration

    chethan md
    chethan md
    TI Thinks Resolved
    Part Number: DP83848M Hi, Myself Chethan from Celliber technologies, Bangalore. I am using DP83848MPHPEP part in my design and using the part in RMII mode to interface to a Marvel Ethernet switch. I am looking for the EVB schematic w.r.t the above mentioned…
    • 11 months ago
    • Interface
    • Interface forum
  • Answered
  • AM5718: PHY: DP83848M connected to PRUSS1

    Masuchi Toshio
    Masuchi Toshio
    Resolved
    Part Number: AM5718 Other Parts Discussed in Thread: TMDXIDK5718 , TLK105L , DP83848C Hi, I'm using SDK-LINUX-AM57X 06_03_00_106 on our custom board. Our board has 3 ethernet ports . It is similer to TMDXIDK5718. But it doesn't have 2 Gigabit (1000Mb…
    • Resolved
    • over 1 year ago
    • Processors
    • Processors forum
  • Answered
  • RE: AM5718: PHY: DP83848M connected to PRUSS2

    Masuchi Toshio
    Masuchi Toshio
    Resolved
    Hi Jian, You are right. Our board was incorrect.PHY address was different from software settings. Thanks, Toshio
    • over 1 year ago
    • Processors
    • Processors forum
  • Answered
  • DP83848M: additional precautions for PoE needed?

    Lo2
    Lo2
    Resolved
    Part Number: DP83848M Other Parts Discussed in Thread: TPD4E05U06 Hello, we're using the DP83848M in a PoE powered device. It's connected to a PoE capable transfomer like this: The raw PoE power is then further processed by a bridge rectifier…
    • Resolved
    • over 1 year ago
    • Interface
    • Interface forum
  • DP83848M: DP83848M: DUT test mode entering method

    Roy Lin1
    Roy Lin1
    TI Thinks Resolved
    Part Number: DP83848M Hi support team, Our customer has some questions. Could you provide the 10 / 100 BaseT test mode SOP for DP83848? It means that the console command to let the PHY send the continuous pattern for 10/100 BaseT, and let scope test the…
    • over 2 years ago
    • Interface
    • Interface forum
  • DP83848M: Crystal Drive Level

    Bernd Sprenger
    Bernd Sprenger
    TI Thinks Resolved
    Part Number: DP83848M Other Parts Discussed in Thread: TIDA-00207 Hello, I am using the DP83488 in a design and I am currently selecting the crystal. In order to verify that the selected crystal operates in its permitable power range, I need to calculate…
    • over 1 year ago
    • Interface
    • Interface forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2023 Texas Instruments Incorporated. All rights reserved.