Search tips
Showing 3,488 results View by: Thread Post Sort by

  • RE: TMS320F28388D: AC adapter for EVMs

    Cody - Thanks for the reply. I have purchased a power supply with a 5.5 x 2.5 mm barrel connector, and have confirmed that it does fit.
    • Answered

  • TDA4VM: How to use active DP to HDMI adapter on TDA4 EVM board with PSDK 7.3?

    Resolved
    Part Number: TDA4VM I tried to remove the following part in board-support/linux-5.4.106xxx/arch/arm64/boot/dts/ti/k3-j721e-vision-apps.dtso - &main_i2c1 { - status = "disabled"; - }; And run 'make linux-dtbs' in /opt/ti-processor-sdk-linux…
    • Resolved
    • Answered

  • How to adapt ethFW for J7200 EVM to customized hardware?

    Resolved
    Release 07_03_00_07 is default to use UART2. I plan to change it to MCU_UART0. It is fails on J7200 EVM. Nothing shows from MCU UART. But I could change it to UART0. The same binary could not run on our hardware. Even nothing shows from UART0. Are there…
    • Resolved
    • Answered

  • DRV8350H-EVM: I have referenced the DRV8350 EVM and have a new design , now it indicated my HALL SENSOR error.

    Resolved
    Part Number: DRV8350H-EVM Other Parts Discussed in Thread: DRV8350 , DRV5021 , MSP430F5529 I have referenced the DRV8350 EVM and have a new design , now it indicated my HALL SENSOR error. I have used the oscilloscope and measured the Connection end of Hall…
    • Resolved
    • Answered

  • DRV8353RS-EVM: What happens if I connect and run 60 degree HALL sensor placed motor ?

    Resolved
    Part Number: DRV8353RS-EVM Other Parts Discussed in Thread: DRV8353 Hi, Please let me know, will DRV8353 chip fails if I connect and run 60 degree placed (instead of 120 deg) HALL sensor motor From datasheet I could see DRV8353 supports 120 deg HALL placement…
    • Resolved
    • Answered

  • BQ24192: USB-to-GPIO interface adapter needed for EVM?

    Resolved
    Part Number: BQ24192 Other Parts Discussed in Thread: USB-TO-GPIO , Good morning team, I have a question about the BQ24192EVM-021 board. My customer is trying to read/write to the registers via the USB-mini port, but it doesn't seem to recognize the device…
    • Resolved
    • Answered

  • RE: PGA460PSM-EVM: Energia code library guides adaptation to ESP32 in Arduino IDE

    Resolved
    Hi Gabriel , When you attempted to capture the echo data dump, did you ensure the DATADUMP_EN in the EE_CNTRL register bit was set to '1'? By default, this value always starts-up as '0' which prevents the echo data dump results from updating. Only either…
    • Answered

  • DRV8353RS-EVM: Lab 11e: Hall sensor start-up with transition to FAST

    Resolved
    Part Number: DRV8353RS-EVM Other Parts Discussed in Thread: MOTORWARE , , DRV8353 I do not see a project Lab 11e for this kit in the Motorware files. How do I make one? I did all other labs that TI supplied to me for DRV8353RS-EVM. Now I need to spin a motor…
    • Resolved
    • Answered

  • DIP-ADAPTER-EVM: Schematics available?

    Resolved
    Part Number: DIP-ADAPTER-EVM Hello Team, it may sound trivial but can you share the schematics or layout, please? How are e.g. the SOT23-5 pins connected to the DIP-8 pins? 1->1, 2->2, 3->3, 4->4, 5->5 or 1->1, 2->2, 3->3, 4->6, 5->8?…
    • Resolved
    • Answered

  • Different USB Interface Adapter EVM response time

    Resolved
    Other Parts Discussed in Thread: USB-TO-GPIO Hi Expert, The customer purchased many TI USB Interface Adapter for factory firmware programing needed . But they found the response time is different from brought from 2017 and brought from 2019. The customer…
    • Resolved

Didn't find what you are looking for? Post a new question.