TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 89 results View by: Thread Post Sort by
    Answered
  • INA186: Looking for solutions to detect 10uA current

    Austin Do
    Austin Do
    Resolved
    Part Number: INA186 Other Parts Discussed in Thread: INA149 , AFE3010 , INA229 Hello experts, I'm looking for CS solution to detect 10uA ~20uA current. This is not a main power rail, but 220VAC GND line. The purpose of CS is to detect leakage current…
    • Resolved
    • 3 months ago
    • Amplifiers
    • Amplifiers forum
  • INA186: Output Swing to power rail

    Gabriel Xu
    Gabriel Xu
    TI Thinks Resolved
    Part Number: INA186 Hi team Customer have questions about output swing to power rail spec of INA186. From INA186 datasheet, it indicate that it could output up to VCC-20mV with Vs=1.8V@10Kohm load. However, output voltage swing diagram shown below indicate…
    • 6 months ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA186: behavior when OUT reach to VS

    Koji Ikeda
    Koji Ikeda
    Resolved
    Part Number: INA186 Hello Support team, My customer inquires INA186 usage, could you support how INA186 behave? E.g. in case of INA186 x500 version, if the sense resistor voltage is 8mV and Vs=2.5V, how the output behave? Calculated output is 4V, but…
    • Resolved
    • 7 months ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • RE: INA186-Q1: OUT pin voltage issue

    Jeffrey Chung1
    Jeffrey Chung1
    Resolved
    Hi Peter, This verification has been finished with Rf=10kohm and Cf=10uF that you recommended, and there are no problems on their test until now. Also they are going to do the reliability tests after that. Thank you for your kind explanation. Regards…
    • 7 months ago
    • Amplifiers
    • Amplifiers forum
  • INA186-Q1: Ref pin clarifications

    ArTzy
    ArTzy
    TI Thinks Resolved
    Part Number: INA186-Q1 Other Parts Discussed in Thread: INA186 , INA190 Hi Experts, Good day. The datasheet does not specify the input parameters of pin "REF": input current vs. applied voltage. Driving pin "REF": requirements to the driving…
    • 11 months ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA186: INA186 - Measure Negative Supply

    groger57
    groger57
    Resolved
    Part Number: INA186 Other Parts Discussed in Thread: INA282 , INA286 Hello, I want to use the INA186 to measure a +/-12V boost converter with one INA186 on each rail. Note that the INA186 supply voltages are provided separately by a 3.3V regulator. For…
    • Resolved
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA186: INA186A5IDCKR

    Simon Chang
    Simon Chang
    Resolved
    Part Number: INA186 We use the INA186 in our design and we have some spike on the output of INA186. We check the spike is come from the voltage noise from our system and we add an RC filter on the output of INA186 to fix this issue. B elow is our simplif…
    • Resolved
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
  • INA186-Q1: Amplifiers forum

    kura
    kura
    TI Thinks Resolved
    Part Number: INA186-Q1 To whom it May Concern Thank you for your support. Our customer is using INA186-Q1 in their prototype. Vs:5V common mode voltage:13.5V differential mode:50mV After vibration test and temp cycle test ,They found this part fail. …
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
  • Answered
  • INA186-Q1: Slew Rate Exceeded

    Dajon McGill
    Dajon McGill
    Resolved
    Part Number: INA186-Q1 Other Parts Discussed in Thread: INA240 , INA186 Hey Team, I have a customer that is looking to use the INA186-Q1 in a 0 to 40V PWM application with a slew rate of 9V/us. What issues might arise in this application since the datasheet…
    • Resolved
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
  • INA186: INA186

    Ian Wang
    Ian Wang
    TI Thinks Resolved
    Part Number: INA186 Hi Sir, Do we have products with current monitor + current limit both functions? Thanks, Ian.
    • over 1 year ago
    • Amplifiers
    • Amplifiers forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2021 Texas Instruments Incorporated. All rights reserved.